Full Setup Start To Finish Oxidean Animal Twin Cat - Rc Boat Maintenance, Flotation, Steering 

Nice boat BigB. Regarding the left driveline shaking; try it without the prop, but with that prop nut. I guess it would still shake. Most likely that prop nut is not centered well. These are not worth much. Better use a lock nut! Just my advice 😎

Big B, that's a big B quality build video.😊 That park pond won't do much for all that power! Can't wait till I see it run!!

Siiick! you got the Animal!😍 Let's freaking gooo!

Brother this setup is SICK !

I also liked you showing how you put cf in the front of the boat. Wasn't what I was thinking and your way sure is easier. Thanks

Why sorry for the long video ? W're waiting for it !

The set up movie. Loved every minute. Thanks for all the close ups.

love the maintenance videos! i use to kind of slap my boats together at one point, when i finished my 6s 1000mm long mono hull i first ran the boat in a big dirty river near my house, first pass an it spat the 5mm flex shaft out to the bottom of the river an i watched the current of the river start taking it, stupidly i jumped in, got the boat an got back out, never again 😂 also took months to find another 5mm flex shaft to fit, now runs a shaft saver and haven't had an issue since

I have learned so much from watching your videos that it compelled me to start sharing my experiences with others!! Thanks Big B for the time you take to make these instructional videos

Nice boat. I used steering cable boots to keep the water out, and a water block on the steering servo to keep it cool. The water block on servo is a huge upgrade.

After the servo tray and one battery tray broke loose in my carbon-kevlar Animal II, I used epoxy and glass microspheres on the seems, trays, motor mounts, etc. I spent a lot of time hoping to ironclad it and then it flipped and ripped the rear mount of the outdrive out of the hull. I had Bill build mine with Castle Hydras but we could not get the 2200 Kv motors to not cog at full throttle with the 6 pole motors so went back to the 200A Hobbywings. The servo in mine also made a lot of noise. I had many issues with my original boat. Bill replaced the boat with his personal boat but I haven’t use it much yet. Bill scolded me for reinforcing various components of the original boat, using QS8s instead of EC8s, and using a plastic break away bolt in rudder when I sent the original boat back. I wouldn’t have reinforced things if they had not broken and here in Florida, there are many turtles so rudder needs to break free. My boat had inward spinning props like my Geicos. They are nice boats but not as robust as I had hoped for the money

Sounds like the servo is binding. Just my opinion. Love the video and can't wait to see it run. Bg4l

Awesome bruv, I found when I was setting up the push pull steering it would always bind and the servo would always fight to get back to neutral. Tried lubricants but just couldn’t get any more play on them, looking forward to seeing it run bruv 🤙

Glad you made this video. I got one also but haven't started on it yet

Excellent video. Not to long at all in my opinion. 👍

Should be some great videos with this boat. Congrats

What a machine!! It’s gonna be a beast

brave touching the props while boat is hot

Amazing how similar the Animal Cat is to my Zonda. A few differences. My water pickups are flush with the bottom of the boat towards the back. 4 pickups… each motor and ESC have their own.

She's a Beauty

Looking forward to seeing how you mount the GPS for speed runs. I've read that they wont pickup a signal through carbon fiber.

Awesome setup. Many thanks for the video. I'm sure these vids take a lot to film and upload. Did this boat come with those 4082's 2200KV's and ESC's or was that an upgrade from the seller ? I was watching another video with this same boat ( animal ) and the ESC's shorted I think because of the conductive nature of the carbon fibre tray holding the ESC's. So just wondering are there any issues with the ESC trays and or the ESC's ? Great vid as I intend one day to graduate to something like this. 👍👍

❤❤props look like brass not copper ,and did ya balance them after sharpening and balancing one prop will spin clockwise and the other anti clockwise .and they both should weighed the same .

if I drank every time I said 'thats what she said" in this video it would have been a lethal game lol

Can you use super glue instead of loctile?

hey bro u think u can get a Blackjack 29 for the channel

What did you end up doing for the rudder? You running without kick up protection?

Nylon bolt, probably M3.

Why didn't you just do a resin fill with carbon fiber chopped up for the tips?

Props should be rotating inwards.

Damn, those props look like trash, why wouldn’t he send it with the nice cnc props he sells?

Beautiful Big B

Styrofoam blocks are all I use in the zelos for battery blocks. Otherwise, my packs just sit in the sponsons. And you see how it runs. Aside from the buoyancy it adds, it's a nice shock absorber! Can't wait to see it on the water! #BG4L!

Quicksilver PTFE marine grease.💯💯💯💯💯💯💯💯💯

If you dont have any Nylon breakaway screws, I might.. Lemme know if you wanna replace that stainless screw on the rudder.. Ill give ya one.

MIP tools. Nuff said.