GDP Portal Gear Lift Install | How To | Polaris RZR | SuperATV 

Well put together video for the installation process. I didn't realize you needed a press to complete this install, good to know as most individuals do not have a large press laying around in their garage.

Very detailed, thank you.....

Good video, well done. You lay it out very plain and simple.

Not sure if it get mentioned in video but make sure you put anti seize on splines before you put hub on

Great video guys!! I'm saving for the billet 4 inch lift for my yxz. I'm pretty sure it's going to be one of the first portaled yxz's on the East coast. One of my first big trips when it's completely done is going to be Moab.

Well this has been an experience, I'm almost finished. Going to end up taking me over 12 hours to install. I'm NO mechanic, I dont even change the oil in my rzr, I have the dealer do it. A couple notes for the newb shadetree mechanics like me (these are probably a given for more experienced people): Get a couple big tables, lay EVERYTHING out on each side of the vehicle. I spent over half my time, searching through bags and boxes of parts and correct tools than actually installing the portals. I spent way too much time walking around the vehicle to get parts and tools. This video has been instrumental in the install, I've added at least 100+ views during the install lol. Order is important, you have to remove some parts to easily access other parts. Follow this video. I tried jumping ahead a few times and had to back myself out. The newer stock rzr front brake lines are held to the arms by tiny rivets (WTF Polaris). So your going to need a rivet gun to add the new brake lines. I would not suggest zip ties here. Passenger rear brake line was not even close to being long enough, I could not get enough slack to put the protector shroud back on. It is what it is. Driver rear, had miles of slack for some reason. Thats all for now, can't wait to get in the hills to try these things.

What a great way to lift your rig buy 4 of thease gain 4'lift and lose ton of handeling .love how you dont need ton of extra up grades it uses the oem breaks pads drive shaft i wouldet mind a beefier longer lower radius arm but if if the ones on rig run fine i would not bother me

great video. what's total time to install?

No grease on the splines??

If I buy the 6 inch portals for a 2016 Polaris RZR XP 1000, do I need a lift kit as well? New A arms? Would love to try these out with 35 - 37 inch tires....

Does the super atv portals come with everything you need to install?

Do one for the 2020 talon 1000r

Do y’all have any 4 inch portals for a Honda rancher 2015 model

Very Nice 🇺🇸🇧🇷

Id love to get one of these jacks for my sxs

Love it😍😍, can this kit be use for heavier vehicles? ?

do you have a video on can am x3 install ? is it the same as the rzr ?

When you did that build on the blue RZR XP was it completely stock with no upgrade aftermarket parts

Wont it run in reverse with the portals installed?

How much wider does 4 inch portals make the buggie

Ok I have 2 sets of portals. I'm putting a new set on now it says to torqe the recess nut to 120ft pounds. of course no one ever shows them doing it or how. wondering because my axel will spin. if you try to put a pipe wrench on axel to torqe the recess nut it will just scratch the piss out of the axel also the instructions say to do the same thing but no inclination of how to actually do it the proper way. putting a impact on it is not getting a accurate torge spec? please answer or upload a video of the important key parts of the install.

Does it make your stance wider?

If only there are kits that mount brakes right after the diffs. You'll get 30% more braking power if the portal reduction is 30%.

So with a 4" portal lift on my 2017 sportsman xp highlifter 1000 atv what does the top speed go down to? Would like to keep as much top end as possible.

Where did you get the lyft

What floor lift is that

Never leave your caliber hanging

About how long does it take to install these?

Informative video the music in the background reminds me of a cheap motel old women smoking cigarettes and a nasty piano player drinking courvoisier looking for some cheap cow utters

Ps is it just me or did he put those pads in wrong?

Portals are nice but way to expensive for me.