Get Started Using WS2812B LED's With an Arduino and FastLED 

For mobile users: In this video, I explain how pixel addressable RGB LED's such as the WS2812Bs work, and how you can control them from an Arduino using the FastLED library. I show how to install the FastLED library as well as get started using it with some demos. I go over the advantages as well as limitations of addressable RGB LED's and how we interact with them (data vs clock+data, etc). This video is the first in my 2 part series on using WS2812B LEDs with an Arduino. Next video will be on writing your own programs and patterns using the FastLED library to control the LEDs, rather then just demos to get up and running. Components used: - Generic WS2812B 30 LED/m strip - Generic Arduino Uno with Atmel 328p - FastLED library I won't add any links for purchasing, this video is not sponsored and all components were supplied by myself, but make sure you choose a reputable source for parts! Links: Arduino: www.arduino.cc FastLED: fastled.io Supported LEDs: github.com/FastLED/FastLED/wiki/Overview Code/issues: github.com/FastLED/FastLED Timestamps: 00:00 - Intro 00:21 - Note on 2 part series 01:05 - [Overview] Why use addressable LEDs? 02:25 - [Overview] Types of addressable LEDs 03:44 - [Overview] Controlling LEDs: FastLED Library 04:16 - [Overview] Steps/Parts 04:49 - [Overview] Applications 05:24 - [Overview] Limitations 07:12 - [Overview] Power usage 08:58 - [Overview] Extra precautions 09:30 - [Hardware] Parts needed 10:23 - [Hardware] Other LED strip options 11:10 - [Hardware] Data direction close up 11:50 - [Hardware] Arduino board options 13:17 - [Hardware] Other misc parts 14:14 - [Hardware] Pinout of LED strip/wires 18:15 - [Hardware] Wiring/hooking it up 19:48 - [Software] Introduction 20:05 - [Software] FastLED library installation 20:48 - [Software] Testing our LEDs 21:34 - [Software] Code examples 24:05 - [Software] Running DemoReel 25:24 - [Software] FirstLight example 26:25 - [Software] ColorPalette example 28:50 - Concluding remarks 29:37 - Credits and links Music: Approaching Nirvana: approachingnirvana.com open.spotify.com/artist/3sS2Q1UZuUXL7TZSbQumDI ru-vid.com Song: Worth a Thousand Pictures (Lapse in Time) If there are any mistakes or bad practices I mentioned in the video, please leave a comment and I'll try to pin a compilation of updates. Production rants/remarks: - Sorry for the buzzing microphone through part of the video. I tried using a shotgun microphone for the first time rather then my jankier previous setups, and the combination of zipties to mount the microphone the tripod, and noisy circuitry in the dummy battery I used made it come out buzzy. - Filmed on a Sony SLT-A33 (and Samsung MiniDV camera). Takstar microphone for A footage, and Fifine condenser microphone for all software shots using OBS. - A33 does not have a clean HDMI output, so we're stuck with the aperture and shutter speed with the HDMI capture card... (It also doesn't read the sensor at full-res unless filming, but then it overheats) Watch this video on Peertube: peertube.tonytascioglu.com/videos/watch/24b7e27c-33c0-464e-82a7-8f8bf68d9890 Thanks for Watching! Produced by Tony Tascioglu tonytascioglu.com

So nice tony... It was very helpful. Many many thanks and good wishes for u.

Very complete explanation hahaha ! Sometimes a little long but very precise and interesting at the same time

OMG POG

Niiiiiice !!!

Do you have to make about DMA transmission by SPI and USART controller LED RGB?

I also use the WS2812B and I even connected them like you did, but my Arduino shuts off, if I plug it into the pc, when I connect the 5V and the GND. Do you know how I can fix this?

:O

hll