Hacking an OSRAM P-VIP Projector Lamp Driver Board 

This worked almost exactly the same way on PH-AIO-215A power board from AEC V302W projector (probed the power wires and got blue as negative, yellow as 5v, and green as 3.3v control). 3rd and 4th pins on the lamp unit are also control, black(-) and red(+5v) wires. Thanks for the guide!! :)

A great video. Excellently explained. Now I have a good understanding of what a projector ballast does. I was hoping to attempt to repair the JVC X series projector ballasts that were notorious for their failures. A Big thumbs up 👍👍👍👍 Subscribed

i am studying through your this video from a couple of years. But do not dare to do that..... bcoz i have different blast and board..... i do not know when i succeed in my project..... thanks so much for such mind blowing video.

Thank you! Worked also with my w600+ 👍 I have used the 12V supply with an random 5.1k resistor to drive the optocoupler. To switch on the 385V from the main power supply I had to connect the blue "Main" cord to 12V. For this I used a switch. So, if I connect line power the 12V are active and the fans, I connected directly, are blowing. If I turn on the switch the lamp turns on. If I turn off the switch the lamps turns off and the fans continue to blow. It's also possible to switch on again... Greatings from germany Steven

The flat panel projection TV models that use DLP mirrors are also using that kind of lamp. I collect the components each time I find such TV in garbage. They have a distinctive slanted back side, made of thick plastic while the older projection TV with square shape, all pressed wood, use 3 black white CRT to project the 3 colors. The lamp need 60 Hz to avoid destruction by internal ultrasonic resonance. The board that power the lamp works like a class D audio amplifier (high power car radio). It takes as input 200 to 360 volt DC, chop this with a PWM signal at roughly 50 KHz alternating the pulse width smoothly at 60 Hz. It is equivalent to a standard switching mode power supply which would be trying to follow a reference voltage which happen to be 60 Hz sinusoidal. The start voltage is many thousand of volt. The steady operation is around 100 volt. After the arc, the voltage is about 130 volt and drop slowly to 100 volt as the lamp warm up (stable after 5 minutes). The arc lamp, like any mercury/sodium and fluorescent, is a negative resistance. The more current you provide, the lower the voltage measured by a voltmeter. Using a varactor (auto-transformer) to increase both current and voltage delivered, the volt meter really measure lower and lower voltage as the current is increased. It is counter intuitive... how the lamp know how much current to absorb without sensing the voltage? If the current is slowly decreased, the voltage measured increase, up to 150 volts. Decreasing more create a random flicker, then the lamp turn off. It need another strike of 2000 volt to start. Another way to start the lamp is to copy the method of xenon stroboscopic lamp. I gently installed a large spring (any wires - raw, without insulation - rolled a few turns around the lamp works as well. I use a plasma lamp as non lethal high voltage generator An alligator clip is connected to the spring and rolled around the plasma lamp. Safety precaution that I found the hard way: A plasma lamp, even separate a few inches from your setup, is able to induce DC in a high voltage capacitor. The microwave oven capacitors all have an internal bleeding resistor which counter act this self charging effect. But the 10 kilo-volt capacitor I used sometime would hold a charge for months. A "small" value of 0.3 micro-farad at 10 kv destroy any arc lamp in a single discharge. The pieces of glass can be heard bouncing in the room, never to be seen again.

Very nice upload. Only concise one on this subject to my knowledge... These lamps are so amazing and I have plans to build a sky light beam with one so thank you for the info on compressing all the unneeded components.

A couple of clarifications 1- The resistor from +5V to CN2, Pin 4, is 330 Ohms (although not needed) and 2- The two pins of CN4 on the power supply board must be shorted (that connector goes to a temperature "fuse" in series with the AC).

Thanks! I had a bad opto isolator and your video helped me nail it without a schematic.

besides the 380VDC, what else should be present on the ballast board for working

Thanks for the great video Is it possible to test the projector lamp using the dimmer control (adjustable voltage) and adjust the voltage according to the voltage on the data sheet?

Dear friends, could the lamp light only by connecting the 380V to the ballast? Or is it necessary to add some more voltage to the small pins?

It was very good, is it possible to adjust the intensity of the light? I want to reduce the light intensity and use xenon lamp.

sir - lamp ballast , lamp are separately available in online shops as a pair - can these lamps be used in led lcd chinese cheap projectors as light source - 4 inch lcd maybe without damage lcd working temperature 70c ?

Will the driver withstand a lamp of greater power? What power is the driver designed for?

Hello, ive got a question. This looks pretty successful. I am wondering how did you put all of this into fixed casing (including the chassis ground). As you took the 5V supply from PSU going to the common Anode Pin3) of ballast. in that case, you cannot put into chassis the ground of PSU and Ballast right? because your 5V from PSU will be grounded by the Common of Ballast board.

ok I took everything out like you. so just follow the steps and I'll be able to identify if it's the ballast? I bought a new bulb and that didnt work

What is the ballast output for the lamp I only get 56 v

just asking...how many AC voltage supply u measured across terminal of the bulb?

Hello, I only just saw your video. Thanks for showing your work. I am restoring a clay paky 1990's fixture and I can use these lighter units. The old ones were 11kg. I have a small usb circuit board like 1"x1" to produce the 5v for pin 3&4. I will also install fans on the ballast as from other video's the mosfets have reliability issues. Many thanks A+

Very Good Video. Much people tries to replace the p-vip in their projektor with an Led . They all stumble over the UART Protokoll. They(me included) are all interrested what does the lampdriver send Back as an OK message to the Mainboard. Do you have some information about this? Where did you found that uart Referenz sheet?

If the lamp turned off but the system odlr the projector is, still working like there is still a sound but no light, what was the problem? The light turned on but after a while, it turned off.

it was nice watching your vedio! i’m try to do the opposite like i was putting a led mode the conventional epson projector but the projector goes into temp and lamp error after 10sec of turning on. could u help to determine how to override the mother board to think that lamp is still there. i can see 4wire coming from blast to motherboard.

hello can you help me in a matter if I have toshiba tlp 2200 projector I would like to cancel the lamp of it I would have to short-circuit the cable, please tell me many thanks

I wonder if anyone knows where the 5 pin connections on the side of te ballast links to.

Excelente Trabajo..!!!! Muy buenos Datos. You are Exellent..!!!

This is great. I wonder what will happen if you fool the lamp and return it inside the project (and fool the projector too, of course). what are the dangers? I have a projector whose lamp comes on some times but most of the time it fail to start and the projector decide to go back to standby. I think because it sometime work (just for few minutes) then the lamp can be forced on by tooling the ballast, and the mother board can also be fooled by shoring some lines. But I have been asking myself what will happen for instance if the lamp fan fail, and the projector has no way to control the lamp? Is the lamp capable of melting some other parts of the projector before it dies by overheating or it will die before it destroy other parts of the projector? Is it possible that it can melt thing in there in the first place?

Perfect to diagnose bulbs & ballasts. I need to do this...

wow what a great video. D557wh projector vivitek . dose this model have a ballast?

can you please tell me what is the signal to the mother board from the bellast

dear sir could u please tell me the names of Ic's which are used in the main power board of vivitek dlp D859 Projector actually the ic was blast and my projector is not turning on so please if u tell me the names of all the ics it would be very helpful to me plzzzzz

hey, what is the imput voltage of the PHILIPS EUC 150 C/00 Lampdriver?

This is a very good solution for checking the lamps as i was wondering if i can use this blaster board with the epson uhe lamps is it possible to do that ? What do u think

Hi. My Power supply blown up. After a visual check I found the LNK364PN is cracked. However before trying to replace of fix or buy a new part of PS I would like to know if my lamp is working. Can I check this with a dvm? Can with do a connectivity check to find out if the filament is still intact? The Projector is 8 years old, so I don't want to invest much. Any advice?

I have not found blue-screen but lamp is ok and brighten. Advice pls......

Great video! Curious if you have ever measured the lamp voltage/current after the arc has started. Any thoughts on how to maybe to "overclock" the lamp? Do you know if the gain setting would affect the power delivered to the lamp?

Hi Kerry, Is it possible to make a bypass to make projector believe that the lamp is ON without lamp connected to ballast. I want to try COB LED as light source. Please suggest

Where can I buy the convigurations, to turn on.those Osram VIP Projector lamp in our specoal usage, not on projector? Tq, Bless You All

Hello, is the Ballest the reason for the projector lamp not igniting?

Hello! The JVC DLA-HD350 projector. The image is there, but the brightness is very low. All adjustments work fine (contrast, chroma, brightness change, aperture, lamp mode, zoom, focus, etc.). When the image size is reduced to a minimum, the brightness naturally increases to a completely normal level. There are no color distortions. The brightness is uniform over the entire area. Three lamps were tried. Two new ones, one used. Anyway, the brightness is low. Moreover, the used lamp on another projector (sanyo plv z5) shines much brighter (according to the application in the phone 4 times). What could be the reason for the low brightness?

Hello, I need one board ballast code pt vip 06 mic, to replace, where i can buy it? thanks

Can give 5 volt from external source to run the control card

Can you start the lamp just by pluging in to 220V ? Will it turn on ???

Dear Sir, I had red your article . I had supplied main input DC voltage to the Osram ballast (180watt) by adding a diode bridge from the domestic 220 voltage. I used a separate mobile phone charger to supply its negative end to pin 3 and positive end to its pin 5. It enlighted the lamp and switching on or off the charger was putting the lamp off or on respectively successfully after seeing your video. Now I want to know the dimmer function from you. Thanx

Dear Sir, I had red your article . I had supplied main input DC voltage to the Osram ballast (180watt) by adding a diode bridge from the domestic 220 voltage. I used a separate mobile phone charger to supply its negative end to pin 3 and positive end to its pin 5. It enlighted the lamp and switching on or off the charger was putting the lamp off or on respectively successfully after seeing your video. Now I want to know the dimmer function from you. This just my hobby otherwise I am surgeon in India.

what is the output voltage of the power supply... please reply me anyone

Hello Kerry. What can affect the flickering (pulsation) of the lamp of epson projectors? Flickering occurs in the "eco" mode, switching to the "normal" mode stabilizes the lamp and it does not flicker. The incoming voltage from 100-240 V +-10% can somehow affect this flickering process or the power supply and ballast are still within these 100-240 V?

i need the lamp power supply

You could also just short the optocoupler emitter collector pins

Can i glow this lamp without the control board attached to the blaster

anyone help me for repairing Epson Projector TW6600???

como podria engañar ballast epson proyector ? ,, ballast PKP-K230N

Thanks, I'll try on my old sony projector, the driver seems to be the same.

Hello, can you give me a name? The Arduino you are using is the same as the one you have And how he used it 🎉🎉🎉🎉to operate the ballast

nice video !!!! I need some help from you and I have IPLAY VCS314 that have 1500 lumens, can it make to 2000 or 3000 lumens !!!!

Have you ever tried to replace burnt lamp with a diy led replacement in a projector?

So I’m testing the ballast now with out a lamp i have my meter on the terminals of the lamp connector when I turn on the power. I hear a click and only see 56v after is cycles 0-56 and is steady at 56v

Can you help me fix Projector's

Dear Sir, I had red your article yesterday. I had supplied main input DC voltage to the Osram ballast (180watt) by adding a diode bridge from the domestic 220 voltage. I used a separate mobile phone charger to supply its negative end to pin 3 and positive end to its pin 5. It enlighted the lamp and switchin on or off the charger was putting the lamp off or on respectively suuccessfully after seeing your video. Now I want to know the dimmer function from you. This just my hobby otherwise I am a general surgeon in India. Thanks. Reply to this comment

hmm, i'm trying to do the opposite (trick the main board into thinking the lamp is on) but i think i'm pretty out of luck there unless i want to hook up some kind of fake serial communication

Hello , I very happy to see this video ,cause this days ,i want find a way to cheat the MB that the ballast is ON . could you help what i need to do this "cheat" the PIN5 signal ?

LIGHT BEAM BENQ MS 500 VIDEO WITHOUT LAMP¿

well analysed

hallo..... plzz 10r 280watt ballets pin out knowleg

What happens if you just put 120v in the lamp?

How to moving heads balast

no mind where to get 380VDC power supply :(

Thank you so much!

Hi. How long can I turn on the lamp without a fan? It will not explode?

Hey guys I have a very unique situation. I have a really old 35mm movie theater projector. It takes a 2k watt xenon lamp but I don’t need something that bright. My room isn’t the size of an auditorium! (Btw people need to know about the dangers of UV damage to their eyes or explosion hazards on all of these lamps). I want to find an old office projector and tweak it so I can take out the optics and just use the lamp as my illumination source. I can’t use LED due to the flicker and the color temperature of these lamps vastly outperforms any tungsten. It would be nice to have a condenser lens although it’s not necessary since the film goes through very fast. I just need to have the lamp always stay on. I actually don’t mind having the whole unit in the lamphouse of the projector. The projector lamphouse itself that 2 massive cage fans in it. I have no idea how the igniter for the xenon works and I couldn’t the original xenon to strike anyway. Not to mention xenon lamps are even more dangerous! But I don’t have enough power going to it to work for the lamp. Is there anyone out there that might be able to guide me along with this projector? I would really appreciate it even though I know this video is old. I’ll probably make video about how I did it since there is literally nothing about this. Thanks!

Dear Kerry, I'm a professor in Mexico. I want to run the dmd module without ballast, lamp, color wheel and fan. I want to use the dmd to project holograms from my computer. The price of a dmd light modulator is prohibitive for me. Thanks for your attention. Carolina Rickenstorff

yo no entiendo el ingles y me parece interesante ..necesito reparar mi proyector

very useful video, thanks.

is this 200-250w lamp? HPS maybe?

❤❤❤

you are a fucking master men. thanks

Me an an assuie ffriend did this 3 and half years ago, nothing new

Someone needs to make a single component compact ballast for these lamps. Utterly ridiculous how complicated they are to operate as seen here. Pissing me off actually..

Hello! The JVC DLA-HD350 projector. The image is there, but the brightness is very low. All adjustments work fine (contrast, chroma, brightness change, aperture, lamp mode, zoom, focus, etc.). When the image size is reduced to a minimum, the brightness naturally increases to a completely normal level. There are no color distortions. The brightness is uniform over the entire area. Three lamps were tried. Two new ones, one used. Anyway, the brightness is low. Moreover, the used lamp on another projector (sanyo plv z5) shines much brighter (according to the application in the phone 4 times). What could be the reason for the low brightness?

Hello! The JVC DLA-HD350 projector. The image is there, but the brightness is very low. All adjustments work fine (contrast, chroma, brightness change, aperture, lamp mode, zoom, focus, etc.). When the image size is reduced to a minimum, the brightness naturally increases to a completely normal level. There are no color distortions. The brightness is uniform over the entire area. Three lamps were tried. Two new ones, one used. Anyway, the brightness is low. Moreover, the used lamp on another projector (sanyo plv z5) shines much brighter (according to the application in the phone 4 times). What could be the reason for the low brightness?