No video :(

Honda Goldwing | Remove Carburetors 🛵

Подписаться 1,4 тыс.

Просмотров 18 тыс.

50% 1

Hello Everyone! It has been a while since last upload.
This is a part of the fuel system section of the project. I repaired the gas tank so no it is time to work on the carburetors.
In this video I remove the carburetor assembly for cleaning and rebuild. It can be a little bit of a pain but not too bad. Removing the carburetor assembly from the Honda Valkyrie is much more of a pain!
I hope this helps with your bike project!

Опубликовано:

14 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@DTBaker-gq4fd Месяц назад

Doing my GL1000 carbs tomorrow. Have only ever replaced throttle cables, so this is very interesting. Thanks for the excellent video.

@masongrace5670 Год назад

I cant tell you how much this video helped me, never worked on an engine before but started working on a 81 gl1100i that hasnt run in 15 years cheers man

@TomAsay64 Год назад

Thank you so much! I’m glad that I inspired you to start working on your bike!

@cncbuss1 Год назад

Great views on how to do this. Thanks Tony! Cheers from Montreal, Canada!

@TomAsay64 Год назад

Thank you! Greetings from Florida!

@TechnMoto Год назад

nice breakdown. at some point I will be using this info. thanks

@TomAsay64 Год назад

Glad it was helpful!

@davycrockett8752 Год назад

Thank you for your thoughful and succient work Brother.

@TomAsay64 Год назад

You are very welcome! Thanks for watching!

@jasonlandry1503 Год назад

Awesome,just picked up an 82 gl1100,very helpfull

@Akifrend 2 года назад

In the case of GL1000 it is nor necessary to remove the intake boots, just rotate them, you neither need to remove the vaccum covers, but it is easier to remover the carbs if you remove the small vaccumm valve. just some tips from my experience, thanks for sharing this video

@TomAsay64 2 года назад

I did try with the vacuum covers on but it was just too tight for comfort. Rotating the right side intake boots may have worked but removing them just made it easier. There may be more space available on the GL1000. Thanks for the info and please keep the tips coming! I’m glad you enjoyed the video!

@annielamote6046 11 месяцев назад

Bedankt Tom voor deze opname!prachtig uitgelegd,veel van geleerd,grts robert

@TomAsay64 11 месяцев назад

Je bent van harte welkom! Bedankt voor het kijken!

@RuhRohRaggie069 9 месяцев назад

thank you I have Clymer for my 83 aspencade but its photos are so dark its all but worthless but you covered it all my friend

@TomAsay64 9 месяцев назад

Great to hear!

@jurgenschneller8478 Год назад

Very well done! So good for me, to learn! Many thanks!

@TomAsay64 Год назад

You're very welcome!

@jamespolucha8790 8 месяцев назад

Man I was fighting with the cables with the carbs mounted , I’ll have to try your way, thanks

@TomAsay64 8 месяцев назад

Those cables were a pain!

@Britcheflee Год назад

Excellent - just how a to do video should be done - saved it for my upcoming job.

@TomAsay64 Год назад

Awesome! Have fun on your upcoming job! Thanks for watching and saving! There are two more videos on the carbs as well.

@edwardallan197 10 месяцев назад

Thank you. Will be doing it all very soon.....

@TomAsay64 10 месяцев назад

Best of luck!

@williamchristie7365 4 месяца назад

Excellent video. I need to replace the fuel line from the fuel pump to the carb assembly. It looks like the same hose you left connected. Is it possible to remove that hose without removing the carbs?