Honda GX200 Carburetor Cleaning - No REMOVAL!!! 

I am impressed by many parts of this video, chief among them, this man knows how to keep his 10mm tools away from the gnomes.

Have now used this to clean house siding and it performed well ru-vid.comUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX I also bought some wand extensions which enabled higher washing without needing a ladder. I recommend both. This unit arrived quickly, was easy to assemble (only had to attach the handle), and arrived in perfect condition. The only very slight downgrade from a perfect score is the design has a low handle and requires pulling from the side. My old washer was an upright model, while this one is more horizontal. Other than that, it's perfect for my needs. It has a great deal of pressure and more easily cleaned the house siding, porch rails and concrete than did my older model. The engine is a bit louder, as well, but the total time to clean was reduced by the more powerful spray. Did I mention it starts on the first or second pull every time?!! I am definitely happy with this model.

Cheers Mike from across the Atlantic. Back up and running thanks to your generosity of spirit. 👌

This video completely solved my problem. Thank you very much.

Wow. Took 3 min to fix after sitting for 10 years. Thank you!!!!!

Great video. followed it and afterwards my GX200 started right up and running smooth. Thank you!

Another great video,MM. We love the up close camera views as your working 💪 👷‍♂️ 👏

Thanks for sharing this video. It’s helpful to get my Honda pressure washer working again.

Thanks Mike from over in Sydney Australia. You saved me from buyting a new motor at AUD$875 or a AUD$300 service cost. cheers Paul

That trick just worked for me! Thanks dude! Uncrewed that jet, cleaned it- fired right up like a bossanova!

Yeah, great video! All of that oil was just from when the motor had been flipped upside down. Hondas are amazing. I have a 1986 Honda GX 340 on a commercial pressure washer also with the original pump. Still runs like a new one. Has been put through the wringer. It does not smoke and starts right up.

Thank you so much, you’re troubleshooting was right on! IOU a beer or two but in the meantime, I wish you all the best!😊🍻

Awesome. Have a GX200 to bring back to life.

MANN I LOVE YOU THIS ACTUALLY FIXED MY PRESSURE WASHER❤❤❤❤

Your the man MOTOR MIKE! 🙏🏼🙏🏼🙏🏼🙌🏼

After the nain jet is removed take a small screw driver and in the throt of the carb push that brass jet down comes out the same place the main jet does there is little holes on it that like to plug up I've been a small engine mechanic for 20 years but I like watching videos because there is always somthing new to learn no matter how long you've been doing it I usually have to pull that little nozzle

Thanks sooo much 😊worked just like u described! Didn’t need to pull the jet on the carb! Sprayed it out and put back together fires right up!!!

Tried everything and this worked thank you very much!

Thank you! You brought back our gx 160 haha

You’re the man. This solved my issue. One season of ethanol in a Honda G200 gummed me up. Your fix helped me out!

Got it running, thanks!

Awesome! Thanks. Very useful.

Thank you soo mutch for your ideas

I am from Bangladesh, wonderful video brother.

Thanks for the video! First pull starts now not 20 haha!

I like it. Thanks

I can DO that! Thanks!

Thanks Man!!!!

Thank You!!

Nice thank you

Towards the base of the carb There’s a filter housing that you can put a wrench on to take it off odds are the ethanol gummed it up a bit too.

Sweet!

Great job man!

Main jet was blocked, cleared it and fired up. Cheers!

Good class

Ty

Great video Mike, I was doing ok until bowl gasket came out and now can't get it back in! Any ideas on how to get it back in? Or should I try get a new one? Thanks again for great video

I noticed you didn't bother putting water in the pump do you have a video on how to replace the seals in the pump?just curious

so to clean the carb on a honda lawn mower which way do you tilt the mower to get easier access to do this no removal carb cleaning? do you tilt it straight up or put on its side?

your killing my short cuts i have used for many years

Strapped one of these motors to a mini bike and man it rips havent changed the oil in it for years though

Will it suck the chrome off a tailpipe?

Mine had another pin type thing with holes in it that fell out now im not sure which way it went....

Need to clean emulation tube

Hey I’m having problems with mines it just turn off every 5 minutes

My question is wat if the oil has rushed down in the cylinder & gotten into the carb & air filter...my engine tipped over & that happened

GOOD JOB , NOW MY SMALL ENGINE MECHANIC , CANT BULL$HIT ME NO MORE AND CHARGED ME🤣🤣 AN ARM AND A LEG

Remember when you wanna empty the excess gas from last season, quickest way is to just turn her upside down.

Hate to be critical BUT after 7 years of sitting without engine having run, WHY wouldn't you remove the long jet, the pilot jet, and the seidment bowl and clean each of them as well. It would have taken all of about 5 more minutes and I'm betting they would have had been gummed up as well. I wouln't pay for this kind of supposed "carb clean"!!

Great video but I would have pressure washed that nasty engine first

properly your missing the transfer tube can be a clog , an next comment its not the ethinol its the water in the fuel, and you can clean the low jet without removeing the carb

Take it off and apart.

HALH ASS way to rebuild a carb!

A lazy poor job, he didn't even clean the emulsion tube, the idle jet, or any of the fluid pathways.

“without carb removal” -Thumbnail shows you literally holding carburetor out of the motor