Honda GX200 Clone Governor Removal

Подписаться 333

Просмотров 65 тыс.

50% 1

In this video we'll be removing the governor of our Honda GX200 Clone Engine!
Song: Domastic - Weird Dream [NCS Release]
Music provided by NoCopyrightSounds.
Video Link: • Domastic - Weird Dream...
Song: Jensation - Joystick [NCS Release]
Music provided by NoCopyrightSounds.
Video Link: • Jensation - Joystick ...
Song: Elektronomia - Sky High [NCS Release]
Music provided by NoCopyrightSounds.
Video Link: • Elektronomia - Sky Hig...
Download Link: NCS.lnk.to/SkyHigh

Авто/Мото

Опубликовано:

13 мар 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@Bjs20247 2 года назад

Thank you, such an informational.

@sabinoponce4582 4 года назад

Hola que tal amigo, con eso que modificaste me quede con dos dudas porque le sacaste el governor y como hiciste para hacelerar el motor.

@goya1936 2 года назад

OK very good thank you for the information

@0Shanna 5 лет назад

>_< no explanation. Why do you put in the metal rods at the valves? I know you should put in stronger valve springs if you remove the governor but those don't look like springs to me. Also you forgot to put a rubber ring on the nut and bolt you used to seal the governer arm hole. That aside, using a mark is a clever way to know how the gear goes back in, I'll remember that one! Can you do a video on how the gas and choke configuration goes on top now you removed the governor? I can't find any vids that explain that.

@TIGFab97 4 года назад

The stock springs are installed back. The metal rods are the push rods. We pulled the cam shaft out to create some room. When you remove the camshaft, the cam lobes and pushrods fall out. So whe just put them back together when we where done with the governor removal. Now (a few years later) the engine still runs. The bolt did never leak and didn't came loose.

@sardulokrido8038 3 года назад

Bis kalau guvernor di lepas jadi manual bisa gk?bos!

@calixtovasquez9493 2 года назад

Saludos amigo si eliminaste el gobernador como se limitan las RPM

@luthmangaemba3085 5 лет назад

Mas nanya mesin saya honda gx360 kalau gas stengah ke atas ngepos. makasih

@oilonionssleat7936 5 лет назад

Luth Mangaemba baasco

@Atom00000 5 лет назад

So I did this exact thing and now my engine has too much compression and won't let me pull to crank. help please .

@Drock8003 5 лет назад

Matt Noguera set your valve clearance There may be trash in the carb clean it You may have an issue with the valve decompression on the cam shaft or the lobes on the camshaft are worn .

@TIGFab97 4 года назад

You did something wrong. On the camshaft is a decompression cam for easy start. Leave this alone.

@brocky78 4 года назад

should quit the f'n dance music & explain properly what & why you are removing the Govenor 👍

@joecruz196 2 года назад

Bad move on the nut and bolt plug. Nut will back off and guess what you ain't going any where fast but a dead broke stop , will be your best move. Good luck...

@chriscollison933 3 года назад

Did you forget the washer that was under the governor cause kinda looked like it!

@jojanrojas5388 4 года назад

Me quedaron más dudas, que respuestas.

@nardi7204 5 лет назад

punya saya mintak gati setang ni udah kocak banget banyak bengkel disini yang gk bisa ganti sulusinya?

@Creatives-World 4 года назад

Can you breif why governor is removed.. what are the benefits for removing it

@matthewmoneta7906 4 года назад

The governor restricts the gas intake and in turn, the max rpm's. Taking the governor out will increase power, but may reduce the life of the engine.

@Creatives-World 4 года назад

@@matthewmoneta7906 thank s a lot Matthew.. Over all if we say how much life of engine is reduced after pulling out governor.... I want to use the engine for making paramotor...

@matthewmoneta7906 4 года назад

@@Creatives-World Go for it if its a honda. If your concerned just don't lay it open all the time.

@Creatives-World 4 года назад

@@matthewmoneta7906 sir have you modified these engines?? Normally the people who modify these engines use it for car raceing. But my usage will be paramotor. So what you believe what changes should i do for increasing HP and RPM..