Hi there. I have a 2019 odyssey Elite and have now replaced the backup bulbs, front and rear turn signal and brake lights, per your videos. I used everything you listed. However, I’m still having the issue of hyper flash on the left turn signal, even after installing the load resistors. I tried flipping the plug in on that left, but no use. When the car auto stops, it will hyperflash on the left. Any suggestions?
I looked at the dealer installation instructions (found a place to get the assembly for under $500), but now I know why it is so expensive to install on those with hands-free tailgate: you have to replace the ECU in the bumper and one of the antennas... And in either case, you have to cut a notch in the underside of the bumper to have the receiver "tucked into" the bumper (unlike the aftermarket ones that have that under-bumper bar that lowers your back bumper clearance even more...) The wire-harness is even more involved (interior and exterior panel removal...). www.collegehillshonda.com/instructions/odyssey/2019/trailerhitch.pdf www.collegehillshonda.com/instructions/odyssey/2019/trailerhitchharness.pdf
Hooked up load resistor as specified noticed after a while of driving they go back to hyper flashing and auto idle didn't work the first day but does today does it just take some time for the van to adjust? 🤔
Night time comparisons aren't as important as daytime comparisons. At night LEDs generally perform just as well or slightly better than regular incandescent bulbs. The true test is in direct sunlight as LEDs do not do as good a job using the incandescent reflectors.
Hi. I have a 2019 Odyssey as well. I used your your video to upgrade to r lights to LED. ESPECIALLY the turn signals with the load resistors. Problem is I ordered the resistors you recommended. Trimmed the necessary parts as you did. I still cannot fit the base for the bulb into the socket because of the two large square like flanges on the load resistors wiring. I’m pretty good at being handy but for the life of me I cannot get this to fit. I have pics if need be. But has anyone dealt with this or is this just operator error?
I am subscribed, and I am from Edmonton, Alberta, I have the exact Odyssey, color and trim! I am learning.... btw, I need to know how you get to the license plate holder - I want to change the light to LEDs
Instead install load resistor in front turn signal , can I install in rear? I think it is easier to install in the rear than in front but not sure it will work.
The flasher relay is look for the an old lode of the lats bulbs led don't use much power relay can't get do that and will make you van think that it has bulb out some flasher relay work on LED turn singnals some have a speed jester so you can have as fast as you want.
The load resistor will get hot, and that's why we use the type that has a heat sink to dissipate heat. Mine is still working and no damage. Just mount the load resistor away from any wiring and you will be good.
LED turn signals i bought caused me hyperblink... Sir, is there any different for the load resistors installing 50W 6 OHM vs. 50W 8 OHM? I want to know which load resistor do I need when I want to install front And rear led turn signal and prevent them hyperblink. As i heard, my car consumes 25W for each turn signal llight.
I have a 2019 EXL. I replaced all the rear bulbs to LED and I have hyper flash and I haven't replaced the front signal bulbs. I ordered resisters but not installed yet. It has been a little chilly do work outside.
You don't need 4 load resistors because the there is one flashing relay that operates the front and rear lights (this is why your front & rear blinkers flash at exactly the same time).
I noticed you have new chrome strips added to your front grill but never did a video for it. Are those just universe taped on strips or they are one piece to replace the oem grill? thanks in advise.
Great Video. It has really helped me a lot. Is it not possible to remove small black grill around turn signal and fog light at the front, instead of working from the back?
dial2fast thank you for answer. But, i was wondering if I have to install load resistor separately for my car’s turn signal light (7440) and fog light (9006) if both of them are not LED from factory? I mean if LED turn signal AND LED fog light causes me hyperflash, do I install load resistor separately?
The 18+ Odyssey EX uses H11 for low beam. I recommend these H11 LED light which you can install and will give you a pure white and bright light output. amzn.to/2KYMZUX
BEWARE! I installed a similar type of product on my late model Toyota Camry and that black connector is HIGHLY vulnerable to moisture and corroded less than two years after installing it and I live in the dry southwest United States.
@@dial2fast thanks. I really like your videos alot. I have learn alot by watching your videos. I wish you could do a video how to replace license plate bulb on 2019 odyssey. Thank you in advance
To much work for an led for signal led light... it is a van after all. Not like I'm going to go fast n furious... with a van down my neighborhood street... lol
