Honda S2000 Double Din - Apple CarPlay Display 

Any time!

do you know anyone who can 3D print the flipped version? I have the cage and bezel, going to pull my dash out to install the cage correctly but I haven't found anyone who can make an LHD version of the bezel so I was going to try the heat-gun-reshape route.

Thanks a lot. I know it wasn't perfect and got a lot of flame for it but I had to try it plus I can always buy another dash. Like you said there wasn't a lot of info on how the cage fits and honestly taking the dash out is the best way due to where the mounting screws are located. I didn't realize all my mistakes I would make until I started getting further into the cutting. Next time will be different. I plan on buying another dash and make it better on round 2 so I can at least screw in the cage correctly.

I am in the process of doing mine right now. I noticed your S2000 has the little mounting ears on the dash that will mate up to the JDM bracket; mine does not, it is an early AP1 and I am guessing they didn't do the mounts then because the NAV wasn't yet out. I will have to overcome that hurdle somehow. I give you credit for trying and perseverance. This isn't an easy task to take on, at all. There also isn't any going back or redos really so for the people hating, until you have tried, you don't know what it is like.

@@briangiller5253 hey did you remove your dash? I want to do this to my 2003 later this year once it's too cold to drive it. I have the cage and bezel but haven't removed the dash yet.

Go job. Some mistakes but next Time will bé different ;). Did you got difficulty behind alpine radio ? Regarding vents behind ?

S2000 dash’s are like $200 , it’s not the end of the world

That was the main reason I filled it in with epoxy and filler to fill in the gap the curve creates. I’m working on a better looking bezel. With this Alpine unit it’s not so bad although the buttons to operate it are at the bottom of the unit close to the bottom of the bezel.

Yeah, the dash doesn't have any indication on where to cut and I only found out the provisions to screw it in where there after I cut into the dash. I'd recommend cutting a small rectangle first, finding the mount locations, then make the hole bigger as needed. Only other issue is getting screws to fasten from behind the dash skin, going to be a PITA. I created the mold because the JDM bezel doesn't sit flush on the US dash and this was my attempt to make a sleek/flush exterior fascia, that I later screwed up, smh.

Mr Brando thanks for your reply!! So how were you able to fit the bracket behind the dash? Wouldn’t the cut in the dash need to be smaller then the bracket for it to fit ? I have picture of the back of the dash to help me some what find out where is at? Just need to know which ones are the studs because some seem to be for the air vent. As for the beZel to sit flush I’ve read about heating it up with a heat gun and reshaping it. That’s what I’ll attempt and then clamp to the bracket (once I figure out how to get there and torque it. I figured maybe I can fit it putting it in sideways or trying to squeeze through the airbag slot or the instrument cluster once removed?

@@ryancue9240 if you're wanting as clean of an install as possible you need to pull the whole dash out of the car and screw the bracket in from behind. US dashboards have all the mounting points for the bracket back there, you just need 7 more screws to mount it. I just did this today and it fits perfectly - the bezel absolutely will not work though - need to go custom or have someone 3D scan the JDM bezel, flip it for LHD dash and 3D print that LHD version.

@@kalmtraveler I did it by eye and used the original bezel I warmed it up and reshaped it to the other side as much as I could

@@ryancue9240 how flush does it fit? just eyeballing this one, if I flex it to try to force it in - it deforms a bunch and I get gaps on the top and bottom so I was going to just try the 3D scan and print route.

I used a Modifry DCI Wired harness made for the S2000 so I could keep the dash controls working.

Thanks!

No, but it is nice to have it and the map options. Especially in the mountains or on new roads. So why not.

Mr Brando well you destroyed your dashboard and devalued your car at least $3000 for one

Mr Brando I’ve seen people stuff the double din below in the actual radio location, it isn’t perfect but at least it doesn’t end up like this

NightRush well it is his car and if he doesn’t plan on selling it I guess it’s a win for him lol honestly thought it was cool.

The Alpine ILX-W650 is a shallow mount unit so not duct cutting is needed. My next unit may be the new Pioneer DMH-WC6600NEX - wireless car play, 9" screen, higher resolution and its modular with the 1" screen.

lmao

@@SamuelMonteiro16 lmfaoooo

Yeah, this was my first try in an S2000 and I made some mistakes but nothing I can fix or modify. I just wanted to capture the overall process not so much my crappy technique, lol!

You won’t boost your car?😂why? It’s built for it

@@Sir3than It takes a hit on resell have 04 GPW/Tan with 38k miles. Its only going to keep going up in value

@@billykolger9646 totally get where you're coming from, but that only matters if you're planning to get rid of the car some day. I had an 02 for about 8 years that I sold and regretted ever since. Just picked up a mint low mileage 03 and will never sell it so I have no problem doing this (though I'll be pulling the dash out to install it correctly)

The way the bracket is mounted in the dash I didn't really need to fasten the unit down so much, so it held in by very tight felt tabs. Unless the car flips over its not coming out. I have a new bracket but havent had the time to put it in. I am working on replacing this unit with another and making a new support bracket.