Electronic ignition system is the type of ignition system that uses electronic circuit,usually by transistors controlled by sensors to generate electric pulses which in turn generate better spark that can even burn the lean mixture and provide better economy and lower emission.
Various types of ignition systems were used lately that are:
1. Glow plug ignition system,
2. Magneto ignition system
3. Electric coil or Battery ignition system,
But all these systems have their own limitations that are:
Glow plug ignition system is the oldest of all and is obsolete because of its many limitations-
Glow plug ignition system has a problem of causing uncontrolled combustion due to the use of electrode as a ignition source, which is solved later after the introduction of Magneto ignition system in which electrodes are replaced by spark plug. Unlike magneto ignition, Glow plug produces high exhaust emission due to the incomplete combustion.
Magneto ignition system:
It is the system introduce to overcome the limitations of old ignition systems, but it has its own limitations-
It depends on the engine speed, so shows starting problem due to low speed at the starting of the engine, which is later solved with the introduction of Battery coil ignition system in which battery becomes the energy source for the system.'
Expensive than electric coil ignition system.
Wear and tear is more than battery coil ignition because of greater number of mechanical moving parts than battery coil system.
Can cause misfire due to leakage.
Electric coil ignition or Battery ignition system - System is the latest of all above and is being used from long time due to its better efficiency and accuracy but it also shows some limitations-
Less efficient with the high speed engines
High maintenance required due to mechanical and electrical wear of the contact breaker points
So, Since in the modern automobile new technologies are introduced and it is found that use of sensors and electronic component gives more effective and accurate outputs than that of mechanical components so the use of sensors with electronic controlled unit becomes essential to fulfill the needs of modern high power and high speed automobiles or hyper series of automobiles, so to fulfill the need for high performance, high mileage and greater reliability has led to the development of Electronic ignition system.
Working of Electronic Ignition System :
To understand the working of the electronic ignition system let’s consider above figure in which all the components mentioned above are connected in their working order.
When the driver switch ON the ignition switch in order to start a vehicle the current starts flowing from the battery through the ignition switch to the coil primary winding, which in turn starts the armature pickup coil to receives and send the voltage signals from the armature to the ignition module.
When the tooth of the rotating reluctor comes in front of the pickup coil as shown in the fig the voltage signal from pickup coil is sent to the electronic module which in turn senses the signal and stops the current to flow from primary coil.
When the tooth of the rotating reluctor goes away from the pickup coil, the change in voltage signal is sent by pickup coil to the ignition module and a timing circuit inside ignition module turns ON the current flow.
A magnetic field is generated in the ignition coil due to this continuous make and break of the circuit which induced an EMF in secondary winding which increases the voltage upto 50000 Volts.
This high voltage is then sent to distributor ,which has the rotating rotor and distributor points which is set according to the ignition timing.
When the rotor comes in front of any of those distributor points the jumping of voltage through the air gap from the rotor to the distributor point takes place which is then sent to the adjacent spark plug terminal through the high tension cable and a voltage difference is generated between the central electrode and ground electrode which is responsible for generating a spark at the tip of the spark plug and finally the combustion takes place.
#ElectronicIgnitionSystem #Automobile
The wait is finally over. I am here with RU-vid's very first Mechanical Engineering Channel in HINDI.
In this channel i will upload videos related to mechanical engineering topics such as Automobile, Production, HMT, Thermodynamics, FM, CAD/CAM etc.
So subscribe my channel and learn everyday
Follow me on twitter: ⤵
/ dashingdanish11
Add me on Facebook: ⤵
/ danish.ali.754
Follow me on Instagram: ⤵ www.instagram....
Contact me: ⤵
mechanicaltechhindi@gmail.com
27 авг 2024
