How i desolder and solder the part of Joystick from PS4 and PS5 Dual Sense controller 

One of the best tutorial around for this specific case! Thank you very much for uploading it!👍

Of the most practical tutorials, thank you for sharing your knowledge

great tutorial. I would love to see a video of your workshop and equipment you use. Great work Thank you 👍

I think you should replace the name of the video to how to replace analog stick (close zoom) because this video is very very good Nice job

That was very satisfying to watch.

Nice and clean Work! 👍👍👍

You're very good. Nice and clean job!

Very professional! thank you for the video!

Great Job and Clean! Thx for sharing bro 🙏

You made it look super easy

great video man

Very helpful. Thank you.

What’s the name of the foil that you used with the heat gun?

That clog-nose on the iron is pretty smart

One question, for example I allready have 1 broken controller and my new one got the same issue with the potentiometer so can I use the old one and use it for my new one ?

Danke dir für das tutorial ich bin gestern nämlich verzweifelt

Tbf, my fav method is with the soldering iron and solder wick. Its clean, fast, and requires little preperation.

Soldering knife tip method has to be the best, i feel like heat gun always runs the risk of damaging components and this seems to be the fastest way too

Super 👍

Hello. What temperature where you using on your solder iron throughout the video? Thanks in advance. =)

ty for your equipment links!! really apreciate that, learning from a pro

What kind of tape are you putting on the PCB board?

what temps do you use?

Professional

hey, nice vids man!!! thx!!! one question? what is that white type of liquid that you use? thx a lot

Can anyone tell me do people deal with the capacitors and resistors on theese boards or just better to get a new one

What was the green liquid stuff that you applied on the board?

Please I try to do it with Soldering iron kit 90w with my 2 ps4 controller the heat pen to the controller doesn’t work for me I need a step by step how many temp on the heat pen and do u have to press on the motherboard controller?? It’s difficult to move one with the First basic step

Soooooo everytime i try throwing solder in the ports like in the video they dont stay liquidated like the first method shows. It just automatically dries up. Any pointers? Beginner Solder w NO Experience so any bit of advice would be appreciated

Clean

Kinda new to soldering, how would you go about fixing if you rip off one of the soldering pads while pulling off the joy stick?

What temperature did you set the soldering iron when using the solder wick

If I wire it do I need to calibrate anything if I extend the cables say 5 inches each button on a ps4 controller?

Hello, what camera did you use to record?

What is this copper mesh used at 0:45? I can’t seem to find a place to purchase it

What’s the green stuff you used and is it necessary to use?

What solder do you use? Will any work? Also what flux is best/ do you use

Can you include in the description the repair green paint material you used at 2.50?

temperature and airflow for the hot air?

Trying this on a bashed up controller I got cheap that has joystick drift with a cheapo solder iron and sucker. Not only is hard to see the tiny holes but the sucker literally doesn’t suck. Probably messed up the board at 450 degrees trying to get the solder of

hangi havyayi kullanuyorsunuz bi link verirmisiniz acilll

Hello what soldering iron do you use pls?

Is there any way to replace the analog without having the soldering tools

what is the yelow think you use to remore the welding ?

After de-soldering, wicking and cleaning up the flux I think I ruined the metal ring things on my pads. @0:52 yours look like nice and shiny. Mine are mostly gone. I've been trying to repair joysticks on my Dualsense for months. Am I screwed or is there a way I can still get the new joystick to connect to the board?

Why soldering braid doesn't work for me? do I need to use flux first!

I damaged the top pad. Where do I jump it to?

At 1:48 you lay down a "tape" to protect other circuits from over exposure to hot air. What kind of tape is that?

My wire came off the mother board on my dual sense ps5 controller I just need a little soldering iron to fix it nothing expensive will a cheap Amazon one work?

great video- 1 question however: how do you address the need to calibrate the new potentiometers that you put in? This is information I received in another video: "We measure the old ones and try to match new one as close as possible, if there is offset, we nullify it with a calculated SMD resistor so the stick in natural position is always in the middle since the calibration is hardcoded in firmware. It's hit and miss really, using knock off bootleg "Alps" will give unpredictable results, while the true originals will have usually closer match with little to no offset correction required. It's sometimes a tedious job" seems like you can't simply just swap in new alps joystick modules and call it a day?

what's the blue stuff u used around 2mins and 45 secs

What is is the silver paper what you put there ???

What temprature do you set your sodlering iron on game console boarda lile this one and what temprwtur is the heat gub set at to remove pins?

could you please confirm soldering iron temperature ? i have tried but soldering does not melt even for my setting at 400 degrees C.

How to prepar plastic bord??

Please is that aluminum tape? Is any other tape under it? I saw some people to use transparent orange tape before using the aluminum, but i dont know what it is. I just broke my Dualsense controller because i didnt have flux and hotair pistol

2:36 - What is the name of the substance you use for repair ?

Wish it was that easy for me

what is the liquid being used?

I hope you see this but where did you get the analog stick? I don't know which ones are real

Im crying for the music man

What do you do if the pins get stuck

Better then factory .

How hot Is your soldering station

I believe you used a bit too much flux there. And a solder pump is more efficient than the copper braid, probably makes less fumes too.

Question, what does the “solder flux” do exactly?

At 2:35 I'm missing the round tin I don't know what it's called there's no more tin on it in the circle

So I melted the battery connector on the board, melted the connector for the light bar and after soldering the new modules on, melted the rubber inside them with the heat gun. They wouldn't budge an inch haha. Oh well, lesson learnt.

Here's some real tips.. from a person with zero experience besides watching these RU-vid videos like everyone else. -When using a heat gun you run the risk of either burning the circuit board or melting the components within the joy stick no matter the distance or temp. (Understand melting points of the plastic parts vs solder.) - When using soldering iron it can only reach a few prongs at a time. The heat can transfer from the metal cage holding plastic parts which can warp or melt joystick. -Solution: find something that will evenly heat up each prong in small increments of time so it won't damage any plastic on either side. Or buy another controller.

First time trying this, im surprised my controller still works once i got done 😅

I don't think it was necessary to wear the solder mask because you hadn't passed the corresponding track

Is a hot air station actually necessary?

My pad came clean off the board. :(

This video is Bs. I havr my iron cranked up to the max and it will not melt the solder on ps5 controller. I have it cranked up to 600 Celsius