No video :(

How-To: 2010 to 2012+ Camaro Steering Wheel Swap

Подписаться 2,4 тыс.

Просмотров 44 тыс.

50% 1

Disclaimer: This modification is at your own risk, we do not take responsibility for any loss of warranty, insurance coverage or injuries related to this modification.
This is a quick how-to guide on the removal of a 2010-2011 Camaro steering wheel and airbag assembly and how to install a 2012+ steering wheel and airbag assembly.
The following is required to do this modification:
2012+ Camaro Steering Wheel: All models interchange (LS/SS/ZL1)
www.gmpartsgia...)
2012+ Camaro Airbag Unit: 23170890 or interchange
Tools:
- 10mm Deep Socket
- T50 Torx Bit
- Breaker bar or impact
- Small flathead screwdriver
- Long allen key or thin flat tool to disengage airbag clips
- Torque wrench
Note:
Watch the video in full before performing this installation and ALWAYS disconnect your battery prior to performing this modification. Failure to remove power has the potential to cause the airbag to deploy.
Music By:
Runaway by Diamond Ace | / diamond-ace-music
Music promoted by www.free-stock...
Creative Commons Attribution-ShareAlike 3.0 Unported
creativecommon...

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 155

@DEATH_BAT6531 2 года назад

honestly i love the 2010 camaro ss interier style

@phonkave2993 3 года назад

I perfer the 2010 wheel.

@Datls1corvette 7 месяцев назад

The paddles aren’t even paddles there just buttons

@buttslappingpirate 2 месяца назад

It's terrible. Simply reaching the cruise buttons are a PITA because of how steep they're angle towards the airbag on the old wheel.

@Lt1mario 4 года назад

Finally someone who does it

@bazingolla Год назад

i wonder why... ugly a$$ steering wheel with that chevy logo 😆😆😆

@tucoramirez9729 3 года назад

the original wheel is so much nicer looking!

@Fade2BlackSS Год назад

Thanks for this guide. Just swapped mine out yesterday with no issues. 🙂

@Projectfd Год назад

Glad we could help!

@douggross8093 4 года назад

Tech tip! Leave the T50 bolt threaded on the last few threads so you won't reef the steering wheel off and possibly damage the clockspring and connectors! Great video man!

@jorgejefferson8251 2 года назад

any tips for locating the clips that release the airbag, does the wheel need to be centered?

@douggross8093 2 года назад

Normally just turn the wheel 180 degrees so it's upside down to get to the holes. Then I normally use a pick or even a small Allen wrench to insert into the hole and push the clip. They are a pain even at the best of times so it all about patience. If you don't feel comfortable definitely take it to get done somewhere. It sometimes helps to take of the trim from around column off to get better access. And most importantly disconnect both cables from the battery before doing any of this. Good luck!

@WOLFBRAND Год назад

Do as he says, guys. I wish I saw this comment before I attempted this LMAO! I need a new clock spring now 🤦🏽

@Infidel67 8 месяцев назад

Great guide, worked like a charm.

@Projectfd 8 месяцев назад

Glad we could help! 👍

@dragonscurse2008 3 года назад

love the 80's sound for this video and the steering wheel how to...

@amolao169 3 года назад

Thanks for share this project! I do the change last week, the original wheel look good but is too big , the 2012 wheel is smaller, better grip and new letter! total cost $400.00. Look Awesome now.

@Projectfd 3 года назад

Glad we could help!

@johnnyappleseed4624 4 года назад

Thank you for making this video. I’ve been looking for this for a few months

@Projectfd 4 года назад

Glad we could help!

@ssjohnny6311 2 года назад

@@Projectfd I've got the 2011 ss with paddle shifters dose this make the installation any harder or dose it not even matter?

@Projectfd 2 года назад

@@ssjohnny6311 As long as you get the right replacement wheel (auto). I assume your current car is auto, so as long as you get a updated wheel for an auto should work without any issue. If you get a manual wheel it will not have the paddles.

@ssjohnny6311 2 года назад

@@Projectfd yeah iv got the auto. L99 engine. with paddle shifters.

@juniorgalvan5672 Год назад

Brother you have the best how to video’s explanations and visuals stay at it just subscribed going to spread your page around to all my friends

@Projectfd Год назад

Hey appreciate that! We're hoping to get some new content going in the next few months!

@feMARIE614 4 года назад

🙌🏾🙌🏾🙌🏾🙌🏾.. now I just need to learn how to replace my front bumper and driver door then my Camaro is back on the road 😌😞

@cw_for_the_win3776 4 года назад

Front bumper is super easy! I did mine with no experience and got it off and on in about an hour! Door is pretty simple to take off a little bit harder to put back on

@sylvestermsmith 3 месяца назад

Excellent video.

@Projectfd 3 месяца назад

Thanks! 🙏

@DonScorchio 4 года назад

well im doing this! hope the paddles still work unfortunately i have a automatic but it was the cleanest unmodified gen 5 that i could find in my area at least.

@Projectfd 4 года назад

Long as you used another auto steering wheel you should be good 👍

@chopnss6722 3 года назад

@Marco Solano Do the paddles work on the auto? I have a 2010 and want to do this but debating because of the paddles

@user-kw9tp2hb5u 4 года назад

Thank you bro for this video

@vinipess 2 года назад

Hello! Nice tutorial, I’m following it for upgrading mine… but I’m installing a LED wheel, so by chance would you know which one of the wires is a 12v switched in the old style harness?!

@buttslappingpirate Год назад

Are the two steering wheels the same depth? It looks like the newer wheel sits closer to the dash versus the 2010-2011 unit.

@buttslappingpirate 2 месяца назад

Hey, I'll answer that question for you; It's the same depth.

@martinyzfr 2 года назад

I would like to do it the other way. 2013 camaro with 2010 steering wheel

@mustafaelectronics347 Год назад

yea same, I'm looking into it

@Clutch_Gameplays 4 года назад

Will this work backwards? I want to install a 2011 wheel in my 2012 ZL1.

@Projectfd 4 года назад

Don't see why it wouldn't. Just like moving forward, the clockspring, harness and splinecount are all the same. Just make sure the buttons look the same on both wheels.

@oliviaclifton5691 3 года назад

Project FD I have a 2013 camaro is it possible to change my steering wheel to a 2010 one?

@Projectfd 3 года назад

Again should work the same. Only thing I've heard from a few people is try to match your trim level. If you have a 1ss without stereo controls and add a wheel with it won't automatically work without some additional changes

@carlgenis514 3 года назад

Project FD that steering wheel looks awfully like my Chevy Cruze steering wheel except the chrome and the emblem on the bottom, do you think the Camaro wheel would fit my Cruze?

@simplybuilt_1708 3 года назад

@@oliviaclifton5691 i have a 2010 and would happily take your updated one instead of mine

@LsxSosa 3 года назад

Will a 6 gen steering wheel fit a 5 gen?

@stingerboi5898 3 года назад

@x__soydeculiacan__x5714 2 года назад

Did you seriously asked that jajaja

@BrittneyMoreno98 3 года назад

I kinda wanna do this for my 2011 camaro but it’s just an LT. I’m wondering if this would make much of a difference. Have the volume buttons on the wheel seem nice though.

@Projectfd 3 года назад

Swapping to a higher trim wheel won't automatically give you volume control. You will need the clock spring and harness to the stereo from a higher trim as well

@christianhurtado7998 2 года назад

So if I have an 2011 SS would everything be fine if I were to swap it with the RS 2014 ones ( the one without the SS Marking at the bottom )

@oscartellez2821 3 года назад

Hi can a 2012 SS camaro steering wheel can be put into a 2010 RS camaro?

@tbj4855 3 года назад

Could I use that same Camarillo steering wheel in a 2009 Chevy impala ss

@jorgejefferson8251 2 года назад

Does the steering wheel need to be centered in order to located the clips needed to release the airbag?...thanks

@zaiasm2305 4 года назад

Is it possible to do the same but with a Zl1 steering wheel?

@Projectfd 4 года назад

Yep!

@ahmadmorrow2749 4 года назад

When looking at the site, what parts come with the 2012 steering wheel? Kinda confused 😅

@joeziko 3 года назад

Can a 2012 Camaro steering will be swapped for a 2014 Camaro steering wheel cover? (SS)

@michaelpast19 4 года назад

If I order a 2012 custom steering wheel from social garage works will a 2012 fit my 2010 camaro ? I appreciate the video it helped me out

@michaelpast19 4 года назад

Btw I also have an auto will the paddle shifter work on my 2010 camaro ?

@Projectfd 4 года назад

Is it just a custom flatbottom or carbon? Long as it's still a 2012 wheel at heart it should retrofit the same way

@DrPhilGood209 3 года назад

So does anyone want to swap me their 2010 steering wheel for my 2013? I like that retro look much better?

@davidchavez1493 3 года назад

I don't know why people like the 2013 steering wheel it literally looks likes the sedan malibu's steering wheel. It's a sport's car not an economic sedan.

@matthewbrown1860 3 года назад

I would swap

@thisissperryo3249 Год назад

Do you know if it’s possible to swap my 10 to a 17 zl1 steering wheel ?

@cluce60 2 года назад

I could use some direction. I started this adventure of replacing my 2013 Camaro HUD. Everything was going well until I removed the steering wheel. I forgot to remove the wire harness for clock spring and pulled it apart (ribbon is hanging out) when I removed the steering wheel 😥. Do you know if there will be any issue if I just replace with a new spring unit?

@Projectfd 2 года назад

Owch, sorry to hear. Yes I'd recommend replacing the clock spring, just make sure it's like for like (IE you had stereo controls/auto or manual) that way the harness will line up without repinning

@SoFLaZ06 4 года назад

oh sup guy, i was looking for steering column data

@Projectfd 4 года назад

Welcome to the data

@FOKESIMTHATDUDE Год назад

want to swap to a 1le sude flat bottom but they only come in manual and my 2010 is auto, will it still work? might just have to do zl1 i guess

@Projectfd Год назад

You'll lose your auto paddles (if you had them), you'll also want to verify the buttons are the same. You can't add a wheel with stereo buttons to a non-stereo wheel car and have them work without a different clock spring and harness.

@FOKESIMTHATDUDE Год назад

just did the swap, did you need a scan tool to remove service air bag light, or do u think the air bag is bad..

@Projectfd Год назад

@@FOKESIMTHATDUDE recheck the clips into the airbag, you should not have a light/need to retune anything

@amoore559 7 месяцев назад

Thanks I hate the 2010 steering wheel looks cheap chrome fall off of the air bag cover

@Projectfd 7 месяцев назад

The grip is also better imo

@FULLMETALCAR 3 года назад

Do you think this will work the other way around like if I bought a 2013 and put a 2011 steering wheel on it well it work

@Projectfd 3 года назад

As long as the trim levels match for buttons it should be the same

@sitandrot 3 года назад

im planning on getting a aftermarket wheel for my 2011 ss but i dont want the airbag light constantly on. do you know of any sites that sell resistors or any tricks to keep it off?

@Projectfd 3 года назад

Never personally done it on a 5th gen but it looks like the common 5th/6th gen resistance is 2 or 2.2 ohms

@youngflamable 3 года назад

does the steering swap keep all the functions from car? I'm planning on swapping my 2013 steering wheel to the 2011 version, I just wanna know if it will keep all the functions from the 2013 model.

@Projectfd 3 года назад

Swapping forward retains all buttons so I'd guess backwards works as well. Just can't add buttons to a car that didn't have them prior, that requires a different click spring and harness

@youngflamable 3 года назад

@@Projectfd okay, i got what you saying, so all buttons work just fine right?

@Projectfd 3 года назад

Yes, if it was a car with steering wheel controls prior swapping forward retains all functions. I'm just guessing but going backwards should be the same.

@walshfamily5704 2 года назад

Am I able to swap from a steering wheel with no volume controls to a wheel that has one and gain that function for the radio?

@Projectfd 2 года назад

@@walshfamily5704 as stated above you can't do that. You need a clock spring and harness from a car that has steering wheel controls to do that

@gabortamas7493 3 года назад

Nice work, but why to change it to a mediocre looking steering wheel ?

@MrMlo131 3 года назад

Can you use same airbag from the 10 steering wheel & install into the 12 wheel

@Projectfd 3 года назад

No completely different unit

@c.heardz 2 года назад

So just to confirm if i switched a 2015 maro LS to a 2011 maro LS it would work..?

@Projectfd 2 года назад

Haven't personally done it but don't see why it wouldn't work. Same would apply for going forward, make sure trim levels match, IE auto to auto, manual to manual, stereo controls to stereo controls. You can't add a stereo control wheel to a non stereo control car without a diff clock spring and harness.

@nighttrain31975 2 года назад

Does the 2010 wheel suck that much???

@Projectfd 2 года назад

It's personal preference. I felt the 2010 wheel was too concave and the button placement angle led to misclicks all the time. Imo the later wheel looks better and is more functional

@youngredrecords 4 года назад

Did the airbag sensor turn on on your dashboard? If not, any tips on what it could be? Cause mine turned on

@Projectfd 4 года назад

Check the airbag connectors they may not be fully seated. Also make sure the connector colors match

@douggross8093 4 года назад

Hi. Know this is a late reply but if the clockspring turned at all while the steering wheel was off then you'll need a new clockspring as the winding inside of the clockspring unwound and broke. It's a thin ribbon of wire inside of the clockspring that is very delicate and the slightest movement can break it. Hope this helps!

@myhighboy13 6 месяцев назад

Wondering why you would switch wheels. The retro one looks so much better.

@Projectfd 6 месяцев назад

Almost like different people like different things...

@serviamstudios Год назад

I’m searching for the reverse of this 💀 2013 Steering wheel looks BORING compared to 2010 🔥

@cw_for_the_win3776 4 года назад

What year can you go up to? And sadly I have the v6 so do I have the use a v6 wheel?

@Projectfd 4 года назад

Any 5th gen is interchangeable, not sure about 6th gen

@dustyua2002 3 года назад

I like oem with the camaro word on it can I put a 6th gen in a fith gen?

@Projectfd 3 года назад

Spindle is different I belive and there is no guarantee the airbag is compatible

@andygomez5743 2 года назад

Where do I buy the steering wheel with the Camaro lettering on it? Can someone help?

@andygomez5743 2 года назад

The one that you are putting on the camaro where can i find it?

@WarzoneDouble 4 года назад

Question mine does not have the volume in the side when I up grade will it work with it or do I need like a new harness or plug?

@Projectfd 4 года назад

Your current wheel doesn't have volume or your new wheel?

@WarzoneDouble 4 года назад

Project FD my current wheel doesn’t have the volume new has it all

@Projectfd 4 года назад

@@WarzoneDouble The clocksprings look to be the same part number across all models so the tricky part would be if you have the dash harness from the stereo to the clockspring to support that. Pretty extreme cost savings if GM did that. Worst case is try installing the new steering wheel and see if it works. If not you may have to track down a dash harness or wire in the missing connections.

@WarzoneDouble 4 года назад

Project FD right that would be so good what I did I took the whole dash harness from a 2015 camaro just incase I need to replace the whole thing since I was trying to also add the touch screen stereo and the HUD dash you think if I replace the whole harness I’ll get all them to work thank you for your help and sorry for all the questions

@pabloproa442 4 года назад

Sebastian Roman Molina did the volume work after all?

@shadyrep1275 3 года назад

Could you do it vice versa. Replacing the 2013 Chevy logo steering wheel and putting a 2011 steering wheel that says Camaro

@jonathanstrait58 2 года назад

Trying to do the same on a 15

@shadyrep1275 Год назад

@@jonathanstrait58 hey did it work?

@shadyrep1275 Год назад

@@jonathanstrait58 I tried it and it was a bust :(

@Havok1105 4 года назад

On the GM website it says this doesn’t fit in a 2011 Camaro convertible is this true or are they just bull shitting

@Projectfd 4 года назад

Gm won't tell you backwards compatible interchange if it didn't come that way. As for convertible I'm not aware of any differences unless there's a different button?

@Dino21 4 года назад

are u serious !!! u took the muscle car looking to give it the chevrolet cruz's steering wheel !!!.

@Projectfd 4 года назад

Steering wheel is used in a few GM models and comes down to preference. There was zero 'muscle car' about that wheel.

@Dino21 4 года назад

@@Projectfd yeah true but the old one looks more american and special .

@shjesus 3 года назад

idont like the old one feels stupid

@ufcpubg1964 2 года назад

Can a 5th gen wheel be put on a 6th gen?

@Projectfd 2 года назад

That would not be a direct swap, you would have to move over clock spring/wiring and you will lose at least 2 functions (DIC controls and rev match) along with heated function (if supported) from the 6th gen that the 5th gen wheel doesn't have. Also you'd have to find an airbag that would be compatible with the stock 6th gen system. Plus, it would be a downgrade overall ;)

@basscartel3737 2 года назад

I just did the same thing with mine but airbag come on anyone know why ?

@Projectfd 2 года назад

Disconnect the battery and remove the airbag again. Verify that the connectors are in the correct orientation and the connectors are fully seated

@ell3071 Год назад

i have tried everything, removed the airbag twice, disconnected the negative terminal, and made sure the plugs were seated and secured, even had a friend double check my work, airbag light still on and i cant reset it with my bosch scan tool. any advice?

@oliviaclifton5691 3 года назад

Do I have to do the torque thing if I change my 201: wheel to the 2010 one or is that optional?

@Projectfd 3 года назад

What do you mean torque thing? Tightening the bolt to factory spec? Yes.