How to Add and Install Fog Lights on 07-13 Silverado 1500 or 07-14 Silverdo 2500 

I have a 2008 2500HD Regency. I have watched hundreds of different content creators in an attempt to upgrade or fix carious parts of my vehicle. You are, without a doubt, the best instructor. You are very concise; you use many descriptions relating to position and orientation; and you go into great detail without skipping any steps. An idiot could follow your instructions and accomplish great things. Liked and subscribed!

If every tutorial on RU-vid are as detailed as yours, there would be 100 times more DIYers out there...

Just finished this install on my 2010 silverado WT and my grey block was stuck underneath the fuse panel. I pryed one side out gently and it came out easy. Pushed my power lead in and you can see from the top of the grey block if its seated properly. I used a multi meter to test if the fog light harness had power and everything is fine. Definitely could not have done this without coming across this video. I salute you for posting it!!!

Extremely detailed need more videos like this !!

I just did this, along with installing new bumper & valance, & added fog lights to truck with none. - Loved the video. Very helpful. Much thanks. A couple things to add: When I tightened down one of the grounds the wiring on the neck under wrench turned & tore ~in half (is aftermarket, may be more fragile), so I backed out & put a big washer on top of the 3 grounds on that side (& did same on other side). Washer holds all in place nicely (video has washer there or bolt/washer combo). Be careful with fragile harness wiring. - 2nd: (this is mentioned in vid) After I took top off fuse box & finagled the big gray handles to remove the top black part, I had to use a LOT of force to remove mine, more than I thought, straight up. - 3rd: (not in vid) The small gray block underneath toward front that you put the wire into has (4) tiny gray over black tabs that have to be pushed back before the gray block will lift. I used (2) tiny screw drivers to remove one end then the other. It was a little challenge. - 4th: (reiterating what others have said) I had a hell of a time pushing in the side orange bar for the wire I'd put in the gray block. I didn't have any fat wires (yellow & black in vid), but found the slot by locating the smaller blue-green & green wires at one end. Thanks to the vid it's easy getting our wire into correct slot & feeling it hit bottom, but I couldn't push closed the orange side bar until I used a tiny screwdriver to carefully force our red wire down further & pushing it down much harder than comfortable. But that worked. Electrical wires: One minute you tear them just lightly putting on a bolt to secure them, next minute you're shoving them into a little slot.

My wire colors were a bit different from yours but the new wire plugged into the same location as yours and it works great. Thanks for such a good detailed video.

Thank you very much you made this very understandable! The way it should be you didn't spend a lot of time talking about your truck. Thank you again looking forward to more videos. I've done a complete frame restoration on my 2011 Chevy Silverado started with a fuel pump replaced fuel pump cross members front and rear tire cross member rewrapped all my wires new cab mounts shocks and struts taking my time after work and on weekends this was one of my added touches I wanted to do. Bought this kit on Amazon thanks again.

Best installation video I've seen in a while

Awesome. Thank you so much for making this vid.

Very helpful. Thank you for your time and knowledge.

Very good video and explained perfectly thanks

New sub very clear and helpful/ detailed

Excellent write up!!

Great video! Very helpful. Thanks

this was very helpful thank you sir👍🏼

This seems to be the most informative video I have seen concerning the install of the fog lights. I understand that this is for the stock style fog lights. However would you have any information where I could find a set of pigtails, that will plug into the new harness, for aftermarket lighting. Thank you for doing a great job with your explanation

I have never watched such a simple and helpful tutorial, you earned yourself a new subscriber! Keep it up

On the hooke road bumbers, there isnt a power lead, but 2 short positive and negative wires, do you connect those to the ground wire?

Thanks 🙏

I ssume the process is the same for gmc Sierra ,correct?

Ordered the wire harness and light switch . I installed the lights, ran the wire harness was . BUT now when I turn them on I get static through the speakers listening to the radio ??

How do you install the fog light housing ?

Edit: see bottom but if having issues this might help: Ok did exactly as you have. Checked grounds. No power to lights? I have 15amp fuse for fogs in fuse box. Should I just tap off the fuse in the block?! UPDATE: Ok for those with same issue I didn’t push the power tap far enough into the grey block. You really got to push that in there. Now it works as it should!

I've tried multiple switches and mine won't work (bought this exact kit). If I jump the fuse the lights come on (no indicator). It seems as though I'm missing a solid orange wire from the switch harness (junkyard info) but I'm not sure where to connect it to on the other end. Any help appreciated. The video is great, it just seems as though i have the only gm on the planet with the fuse and relay but they aren't wired to the switch

I put the new bumper ends on with the lights wired the wiring harness when it came to installing the wire to the fuse box mine is different I don't have that little block that you have! It's a 2011 Chevy Silverado LS. Help!

Thank you! What is the part number of the required harness?

Where can I get the fog lights and anything else I need ? I have the 2500 bumper hd

you never showed where the plugs actually plug into? they just plug into the fogs?

Where does the red wire attach on the block for a diesel. I noticed that you only showed this for a gas burner.

What’s the part number for the fog light bracket?, that’s the last part I need

What do you connect the plastic to I don’t see anything under the bunper

Is it normal that the switch inside the truck doesn’t illuminate?

I did everything you did and I know it’s correct but my lights don’t work and everything is brand new. Any possible reasons? Checked the fuse and relay and everything is good. The light also pops up on the dash like it is turned on.

There are 2 different wiring diagrams. 1 for gas and 1 for diesel

My dome lights seem to stay on once I installed the new switch

The only thing I can think of is my block is attached to the bottom of the fuse box that you're lifting out. It's not on the bottom like I see in your video

How u put the fog light housing on the bumper

Do I buy 1500 bezels or 2500 ??

I followed your instructions but foglights don't come on at all

You have a tiktok???

My silverado is a 14 I'm doing the same mod .my question is will it work the same if I install wire in same position. The fuse is there but no place for fog light relay.

Why did you remove the lower interior panel and side panel?

How are the fog light housing holding up?

Can you reply quickly? I’m in the middle of the install and my wiring is not the same as yours