How to Balance & Tune Idle Triple Weber Carburettors

Подписаться 834

Просмотров 26 тыс.

50% 1

In this video, we show you how to do a basic tune on carburettor balancing, idle mixtures and idle speed on a Triple Weber Carb setup. This set is on a 202 in an EJ/EK engine bay.
This set uses our house engineered ProHex Linkage setup.
Linkage Kits: www.recarb.com...

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 18

@andrewb3497 3 года назад

Best advice is to start by following the Weber Tuning Manual and use the progression holes to align the throttle plate on all 3 carbs to be in the same position - which is the edge of the plate obstructing the first progression hole. If done correctly then the air flow meter will show the same on all intakes (assuming the throttle plate shaft is not twisted).

@hassanmalik5975 4 года назад

Thanks for this good job mate👍

@andrewb3497 3 года назад

Very important to check for fuel leaks as shown @2:37 !

@ahcrx 3 года назад

Thanks for this video. Can you do a video on what the differences are on Weber carburetors. Choosing the right one for your car etc.. E. G Weber 32/36 ,34/34, 38.. Would be awesome for beginners wanting to understand Weber's.

@andrewb3497 3 года назад

Have a look at the Weber tuning manual (also some details shown on this video : ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-qndixQxhV_8.html )

@garypotts7120 3 года назад

Very good video

@LouisPadwell 4 года назад

superb can you just confirm when you are balancing and you disconnect the linkage i am assuming the adjustment you are making is the effective the tickover screw as i cant quite see? On my triple set up i have all three carbs connected to the throttle bar so i guess the best way will be to disconnect these and try and balance them to the carb that has the throttle cable connection I am assuming? Great video best i have seen

@andrewb3497 3 года назад

Best practice is to have them all disconnected and start by adjusting each carby throttle valve so the edge of the valve aligns with the first progression hole. With this done each carby should flow the same and as such they will be balanced.

@justalf Год назад

Hi can you help, my weber dcoe 40 (italian) leaks fuel after a hot run from the O Ring, between manifold and carb..... im running the smallest facet fuel pump so not sure it is the fuel pressure..... and its only after the engine shuts down... look forward to your thoughts

@iFightBears23 3 года назад

hey what linkages are you guys running to the carbs?

@steelofcrom 18 дней назад

My idle mixture screws do not respond to change the value on the synchrometer like that, no visible chanege in fact.

@recarbaustralia5772 18 дней назад

Hi. Please check to identify the right adjusting screws: Idle speed screw, bypass screw (not demonstrated in this clip), and intercarb balance screw (on floating carb linkages) will adjust air flow on the syncrometer. Idle mixture screws will alter fuel mixture strength (not measured with the syncrometer)

@donwest5387 8 месяцев назад

"tune idle"?

@israelrosario2896 3 года назад

Hi ! My name is Israel I have a 1980 Toyota corolla with 3tc engine , with 45 DCOE Webers carburators. That need to be tuning. Would you please give me some advice ? Also where I can get the linkage system you have in the video . V/R Israel Thank you very much!