How to center your front wheel and brakes - HONDA RUCKUS 

Im doing this soon. I have been having issues with this. It rubs a bit to much and at certain speeds causes a harmonic vibration... whomp whomp whomp sound. Everyone pay attention to this, I wish I had this months ago!

Thank you sir for sharing informations about how to center the rotor disk.You helped me about my issues for my YAMAHA TMAX 500 2009 model ,because I chang the front rotors 267mm with bigger rotors (oversize kit 298mm)and now when I brake I feel vibrations and maybe is that the calipers doesn't line with the rotors,so I have to check it.Thank you once again sir 🙂

Great video brother crystal clear explanation if possible do a video for rear wheel as well with disc brake , and one more question in some bikes wheels are a bit offset from factory itself in that case how will we center if possible make a video ❤❤❤

Hey I have a 50 cc song fang,I just built a 150cc engine to put on it,but my tire won’t fit.would a ruckus be the same thing?

I'm from Brazil, would you like to know where I can buy this wheel and tire? I have a project to make Honda ruckus. If you can help me, thank you

Umm.. Isn't that tire backwards?🤔

What is the number of wide rear and front tires for Honda Grom 125cc motor

Am I dumb or is his tire really on backwards

greetings where to get rings and wide Honda Grom tires I want to make it pretty

Where did you get those wheels? They are beautiful 👍

Do you have a how to alignment video?

Great Video Matt, like always great content keep being these great videos out .... WE NEED THEM

I’ve installed a probld front disc set up my wheel’s doesn’t spin to freely maybe I have to brake it in?

Great video 👍 I recently installed dual calipers on a old Harley, it would have been a lot easier if I watched this video beforehand.

Thank you! This just cleared a lot of “wtf” 😂 thanks again!

Sub español

Is your tire tread direction going backwards?

Nice video…Question front wheel speed caliber alignment with this being used on the front wheel. I have a vitacci spark 150cc.

Hey how you doing I've been subscribed to your channel for a couple months now I see you know what you be doing with the GY6 engines I just bought me a Venom x22 GT automatic I was wondering if you can help me with some upgrades on it

I bought a Red Fox falcon 200 put it out by Dong fang it’s actually 168 cc, is there an upgrade kit to make it 232 cc

Helped me! Thanks. How tight do you tighten the axle bolts on each side?

Hi ive gotten a chinese moped, its a vip 50 clone and the shocks are reeeeeaaallly hard to find in order to replace i was wondering if i just bought a somewhat similar shock, could i just adjust and mount the brake caliper any which way i want as long as it worked properly or is that a bad idea?

Hey Matt Love all the info you put out here so much help to us ppl! I have a 2020 maddog trike. It’s a piece of work. I work in her daily I knew nothing about scooters when I bought it but I’ve pretty much figured everything out from you and a couple other folks here I seem to have tore up the side and spider gears. I’ve searched the internet for over a month. No one seeing to have a clue as to where to get them. Do you have a line or know where I would go to get new spool gears any info greatly appreciated

Dong fang

Matt, have you ever come across pads being to thick for the rotor to fit? I bought an online kit several years ago and the rotor won’t fit the caliper unless I force it.. at that point it’s like having the brakes permanently locked

can you guys do a wiring procedure for a baja reaction 150 i recently bought a big bore swap from you guys, ive got questions about it and i took the wiring out becasue it was bad i dont know to rewire it

I read that the axle nut cant be tighten that much so that the wheel can spin freely is that so? Also when i brake my whole steering shakes what can be the cause of that?

Will that front end fit on a Honda Navi?

Good info, I always shim with thin washers, equally, any space left over so when tight it dose not pinch the forks so they move smoothly without any binding.

Where is your honda cub now?no more update?

Do you know if a shortcase GY6 is short enough to fit into a CHF50 Metropolitan without cutting any of the bodywork to make it fit?

Thanks Matt, another great video hope you have a happy thanksgiving my friend. Thanks for posting.

Thanks bro! Saves me $ and time! Do you have a rear disc brake conversion kit?

I do not have trouble front two wheel but on rear wheel is loose I had tire replace but was not balance I think is inner bearing to clutch but not sure! Rolling Wrench

Thanks Matt!!! That video is exactly what I needed.

I noticed the hub you are using has the notches for the speedo gear to fit into, i noticed that its a slightly different color. Is this a piece that can be add? I am using the FLP hub and wish to continue to use the cable driven speedo. Can this be purchased?

Thank you! Ya I will be doing this and pulling the washers. Measuring them and making the spacers solid on both sides. I am strange like that. Both will work just fine. Being a machinist has given me the eye for detail. Makes me respect the details that others put into there build. Once again thank you for doing what you do bro.