How to change the bearings on a Onewheel with Sean Nelson

Подписаться 10 тыс.

Просмотров 66 тыс.

50% 1

In this video we learn from Sean Nelson on how to change the bearings on your Onewheel.
Why would you want to replace the bearings on your Onewheel? Replacing the bearings is arguably the most important item to give your Onewheel motor the longeviity so you can go endless miles. If you are over 1000 miles and are starting to hear "clunks" when you transfer from your toe side to your heel side, you likely need your bearings changed. If you are hearing constant clunks or clicks, you should stop riding your board immediately and get your bearings replaced. Contrary to what some might say, the sound IS NOT cosmetic and the more you ride with the clunks, the more you're damaging your motor.
After this bearings replacement, my Onewheel was riding smoother than ever. I felt like it was even smoother than my other brand new XR. It really does make a difference.
The best bearings your money can buy are SKF 61907-2RS. Please be aware of counterfeit bearings on the market.
Disclaimer: Any time you take apart your mod, you risk voiding your warranty and damaging your board. Changing your bearings is inherently risky. This video is a courtesy instructional video and we cannot be held responsible if you damage your board, void your warranty, or injur yourself during the process. Mod at your own risk.

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 191

@illygah 4 года назад

This is the best internet video featuring the Onewheel.

@19jc80 5 лет назад

I love that he throws some lite digs in on Future Motion for their bearing and o-ring selection/installations.

@Dawn2DuskAdventuring 5 лет назад

Bearings guy needs to post his business card lol

@eevees 4 года назад

www.stokelifeservice.com to find a Onewheel repair person near you.

@jacobngotngamwong4889 6 месяцев назад

doesn't work :( @@eevees

@alanmcnamara9155 5 лет назад

Interesting video. I remember doing similar work on Boeing 747 engines in the 70s. Also nice to see the guts of the Onewheel and how it operates.

@e1.camino 4 года назад

Those bearings are so smooth I can feel it through the camera.

@chadwickwicky67 5 лет назад

Thanks again for the vid! It gave me the confidence to change my bearings myself. I went the 2x4 and hammer plus being patient and careful and it was easy! I used a socket etc to get the old ones out and to fine tune the final seating I used ball joint press end tools plus dowel/hammer. Smooth and easy thanks to you! Btw I measured the torque breaking loose the small hub screws and I averaged about 30 inch lbs. I know loosening is going to be higher than tightening but 30 inch lbs is not much pressure so I felt comfortable torquing them to 30 inch lbs going back in. Again can’t thank you enough for taking the time to do this for us! Smooth sailing again. Went with the Burris ceramic @ $32 each I figured it was worth a try. The SKF ones were $100 ea at my local distributors! If the Burris ones doesn’t live up to the job I will absolutely spend the dough on SKF on the next change but so far these are silky smooth!!!

@TomMarsh1010 5 лет назад

I ordered a OneWheel about a week ago, it arrives on Monday. That people are talking about thousands of miles is amazing. I can see the complaint about the sloppy o-ring installation, but that is a really tight looking motor. Gives me a strong sense as to why they have their reputation for ruggedness... and that a bearing upgrade might be a good project to get behind.

@aliamirkhani5031 5 лет назад

I just ordered mine! Super excited to hop on one again, as I was demoing my colleague’s. As a mechanical engineer I definitely appreciate the in-depth tutorial and seeing all the pieces that make this a $2000 ride. Thanks and hope to see more mod/maintenance vids! Subbed

@bryonmurray9691 3 года назад

Hey, I noticed you saying you didn’t have the torque specs for all the bolts. I am aerospace electrician. Our torque values are gleaned from the size of fastener and what type of metal fastener is. Now I realize the delta factor for material one is fastening to, but as a base line…I can get you you’re beloved torque values in 5 minutes is you give me size and material

@mynameisanyname 5 лет назад

Mister Nelson: best Onewheel mechanics teacher.

@marsrover001 5 лет назад

Just did mine. W O W. It's a new board again. So crazy smooth. I used a combo of wood and a drill press (used as a bearing press) to seat all the bearings. Took a bit longer than having the proper tools but worked fine. Mine was at 1200, no drops no bonks, but I didn't keep it clean. So the bearings wore faster. Side note, I had 2 different colored bearings stock. Different brands. Weird.

@cleveryoutubename8568 4 года назад

Which new bearings did you use? What do you think of them?

@quantumvortex3942 3 года назад

I scored the O-Rings from my local seal shop where they are a stock item off the shelf for $1. They are a 33mm x 1mm standard rubber O-Ring to order. You can usually reuse the large O-Ring around the cap but they are also an off the shelf item called a BS 046 or 107.67mm x 1.75mm standard rubber O-Ring.

@jonnyboymclain8938 5 лет назад

Thank you for making this video. I was able to complete my bearings change on my xr giving you full credit.

@seanc.5310 5 лет назад

This was fantastic! 💯I was curious about the nuances of the onewheel motor and bearings. I've got the beating press and correct tools from doing car repair and restorations. My Onewheel has low miles still but can totally do this with confidence after watching you.👍

@texasredfox7607 5 лет назад

Youre finger illustrations of dirt causing uneven seating of the bearings deserves an award of some kind....

@garydeangelis1640 5 лет назад

McMaster-Carr sells quite a selection of o-rings in various materials. It would be interesting to know the width of the o-rings to see if there is an off the shelf replacement.

@SeattleRingHunter 5 лет назад

Refreshing to see a technician on RU-vid that actually knows what’s he’s doing. Might reconsider the Teflon tape trick with a make an O’ring kit method as possibly preferred since it’s just acting as a dust cover if an appropriate replacement o-ring can’t truly be realized. I see a bunch of one wheelers heading down to Harbor Freight to buy a press now LOL

@pantherpev 5 лет назад

Just a little tip throw the bearing in the freezer and heat lamp on the metal parts a little oil also helps.

@JimiPumpkins 3 года назад

Thank you, got my first swap done, easy thanks to this! Fun to watch too 😎🤙

@brandonaskins7969 3 месяца назад

Awesome video, very informative!

@yankeeproud3818 3 года назад

This guys playing some bangers in the background

@thatalaskaguy 4 года назад

Great video and the banter is hilarious, nice job!! I was surprised to see how thin the bearings are.

@dietm.2249 5 лет назад

Very informative talk about bearings, thx for that. good craftsmanship also

@watchncarry9593 5 лет назад

Great work and instructions

@wigum12 3 года назад

you can use the old bearing to press against new bearing to install

@JJpleex 2 года назад

Just make sure you’re making contact through the outer rings and not the inner rings

@300zxdriver 5 лет назад

Usually places that sell bearings also sell o rings. If not just caliber o ring to find out its dimensions then you should be able to find one.

@ButterBallTheOpossum 3 года назад

A bicycle repair shop is a good place to start.

@fmadrid91 5 лет назад

Is it possible to get this guys contact information so I can pay him to maintenance my board?

@Dawn2DuskAdventuring 5 лет назад

Dude I was thinking the exact same thing. I’m actually stressing this process because I already know I’m going to ride my board enough to need this.

@chadwickwicky67 5 лет назад

Hey guys it’s easy, don’t stress. Patience, sockets to knock the old ones out which comes out super easy at least for me it did. A few Wacks with my 2 lb hammer and right out... Small piece of 2x4 and again careful to keep it even and start with light taps and when you’re 100% sure it’s even and enough to hold in place. You can start to hit with more pressure. A cylinder shaped big socket etc or whatever you can find, I have ball joint tools so luckily I found a piece that matched the outer part of bearing perfectly to finish searing it. But seriously very easy and you’ll get to know the motor etc and will be very happy you did it. I bought some electric motor oil 3 in 1 brand as well, after wiping down my motor and the surroundings squeaky clean, . I wiped a light coat of that oil as well, everything silky smoooooooth!!

@JasonDavis103 5 лет назад

I'd say your best bet is to join your local Facebook Onewheel rider's group, if you have one that is somewhat near you regionally. For instance, I live in South Florida. And about 2 hours drive south of me, I connected with a guy who could perform these type of services when I need them. And to me, it's worth hooking up with him on one of our days off, tipping back a few beers, him cranking on my Onewheel, etc. Good luck!

@TLil21 4 года назад

Yes I would love that so very much too!

@eevees 4 года назад

Head to www.stokelifeservice.com to find a service centre near you. Most can perform bearing changes.

@wizardmix 4 года назад

@Shredd Labs In the description above you're noting SKF 61907-2RS (as in Sam) but in the video itself the number is SKF 61907-2RZ (as in Zebra) would you please confirm the correct nomenclature? I am ordering the bearings directly from an SKF distributer and want to make sure I'm ordering the right ones. I assumed Z not S. Thanks for your help!

@eevees 4 года назад

Sorry for the late reply. I'm just seeing this now. The "S" is the better one with a better rubber seal for dust/dirt but the Z will also work.

@wizardmix 4 года назад

@@eevees Hey thanks for the response, I already went with Z all those months ago. Another question is that there's someone on the OW page selling these SKF bearings for under 40$ each. I paid A LOT more for them from a brick and mortar store. Is there any reality to getting these for that little or is it likely a skam?

@eevees 4 года назад

@@wizardmix I think they're legit as he's reputable. Someone he is selling them at wholesale cost.

@JJpleex 2 года назад

I am a bearing engineer and the note that is made at 12:30 is extremely important. It is not advised to install a bearing with a rubber mallet but if you do, make sure that the intermediate piece you are striking is in contact only with the outer race and not the inner race. If you strike the bearing through the inner race that impact load will travel through the inner race, through the balls and then into the outer race and can leave indentations in your bearing which would make it noisy and cause it to fail early.

@JamesReedy 4 года назад

Neo magnets are extremely brittle, one oops and you’ll crack one of those segments. Seems like a good job for a 3D printed fixture, we use lots of stuff like that in loudspeaker construction and reconditioning.

@heyitsmaez 3 года назад

Bearing guy! lol...Thanks for sharing the video

@brianbailey7128 5 лет назад

Good information here. Thanks.

@huckuxsta3190 2 года назад

Awesome vid thank you. What Is the ton rating on the abour press your using? Please ?

@eevees 2 года назад

We use a 3-ton press which is overkill but you need a big one in order to fit the Onewheel hub.

@charzy888 4 года назад

I have the bearings and new tire, just gotta find the confidence to take it to bits. UK really needs a service centre.

@gunsite45 5 лет назад

Awesome video, guys. Thanks for posting. I'm a little bummed to hear that FM would use cheap bearing just to save a buck... Ugh. That's capitalism I guess 🙄 How did you notice the bearings were going bad? Axial play in the wheel? Stiff rolling?

@cesarguerrero5630 5 лет назад

Does dirt get under the float plates? Trying to decide if it’s a good idea for me

@jerseyrotaries 2 года назад

You guys work on stake boards what do you know about changing bearings? A press doesn't always work .. tapping rhe outter race is perfectly fine

@fltblkcorrado 3 года назад

One Stop Board Shop carries the O-rings.

@biancar.6625 3 года назад

hi, great video. Did you use some kind of glue/adhesive to seal the motor after replacing the bearings? Is an adhesive necessary to prevent water or dirt from getting into the engine?

@JJpleex 2 года назад

The bearings are sealed and act to seal the motor

@huckuxsta3190 2 года назад

Thanks mate , comprehensive and good humor , pleasure to watch . Through a national bearing supply company in oz I ordered skr619072-rs , was told if that couldn’t get they would Supply the equivalent. What I received NSK6907V vCMNS7S107 dimension 56 x 19 x 13.75 provide with a seal kit , As I am not and it seems inevitable you are ‘the bearing guy ‘ what’s your option are the NSK I have been supplied Equivalent or what ? knowing ( I think }that the dimension size on SKR 55 x 35 x 10 from memory makes these others not even close doesn’t it I will talk to the shop where I purchased when they reopen after the weekend and to find out all the way it is reassuring to know I’ve got that bearing guy there by my side when I’m doing change over home ,alone cold and lonely knowing that you are always there at the push of a button Thank you

@jimkono4100 Год назад

Thanks!

@JackMasterOfNone Год назад

I know this is old, but this is great. I need to do this for my GT and am pricing out the press. How would I go about obtaining the machined jigs? Or are the dimensions for the jigs available somewhere, I could then have them machined?

@norbelsemaj3870 3 года назад

So if you don't do all of this. Is your Onewheel will still work at 8k Miles over

@howiedune3099 5 лет назад

Good video. Thanks!

@joshgreen4608 4 года назад

Copper lead aluminum or stainless tube slightly less than the internal diameter of the magnet ring would help when having to install the internal bearing past the magnets

@Gregg0112 5 лет назад

The thread sealer tape is definitely not gonna seal that completely. They sell o-ring maker kits.

@TheStoffl91 5 лет назад

Nice video! Do you know how long the active part of the stator approximately is (length of the laminations) and how many magnets are in there?

@jsin01 4 года назад

How's the skf bearings working out one year later? Any thoughts on the burris ceramic bearings?

@eevees 4 года назад

jsin01 They’ve been holding up well - 2000 miles later! I wouldn’t recommend ceramic bearings in general as they aren’t meant to have the kind of force on them like landing drops on a Onewheeel.

@kevincannon9564 4 года назад

Well damn im scared now i got 2000 and some change on my XR and the stock tire still hasn't worn out but yikes wonder what my bearings look like

@eevees 4 года назад

You're okay until you hear "clunking" or "grinding"

@jeremyrosenahagen4577 2 года назад

Is it normal for these bearings to cost $150 or so each?

@GohmannG5 4 года назад

Can you please let me know the measurement of the wooden dowel you use to hammer out the axle?

@RoQu3 6 лет назад

Wow the motor has a mini board inside right? I thought it just connect directly to the controller

@Kikesurf1 6 лет назад

Those are the hall sensors for the motor.

@eevees 5 лет назад

I'm assumung the gyroscope or accelerometer

@beefcakejake7566 3 года назад

I have the badger pint protector kit on the way, is it a risk for the grease to get in the motor at all?

@rui189 Год назад

friend how much do you charge to do this work on a Gt wheel?

@LBS-33-33 4 года назад

How many miles do the stock bearings last? I have 1300 miles on my board, but i rarely ride on wet roads, do mostly street riding and i clean my board regularly.

@adamhearts9195 3 года назад

Same Q

@TLil21 4 года назад

Where is Sean Nelson located? May I get his contact information?

@seanonewheelnelson3987 5 лет назад

Please note the fully sealed bearing is the 61907-2RS buy this bearing and not the 2rz

@motonvipr 5 лет назад

are there ceramic ball bearings for the OW XR?

@chadwickwicky67 5 лет назад

svtsnake Burris offers ceramic bearings , Craft&Ride website is where I seen those , was also just about to order them until I seen this, now I’m torn ....

@wizardmix 4 года назад

I just spoke with the distributer, they seem to think that Z bearings are better for the onewheel due to heat/temperature variants being a factor.

@Reedith 4 года назад

What brand and size press is that ?

@brettknoss486 5 лет назад

Why not use Loctite on those bolts that always come loose?

@davidse4486 4 года назад

I wish I had these press tools ....

@JamesReedy 4 года назад

PS - Is Future Motion shitty about spares? The o-ring thing is ridiculous, they won’t sell spares so people can rebuild their hub?

@eevees 4 года назад

Yeah, they don't want people repairing or modifying their boards so they will not sell spares.

@JamesReedy 4 года назад

Shredd Labs that’s a bummer, I guess they want the repair revenue. I gotta think the o-ring could be figured out. Apparently they won’t even sell you screws?! I noticed one of the tire change videos admonishing to not lose any screws because they’re, “very hard to find” one would hope 15 mins on Grainger or McMaster would do it.

@zewise1 3 года назад

So Sean works at Float life? Or is he a Van local guru?

@eevees 3 года назад

No but he's definitely a local shredder and guru.

@shrilz 2 года назад

Anyone know where I can get some bearings for my V1 OneWheel?

@mastermarc22 6 лет назад

"cosmetic sound" right? 🤣🤣🤣. A dab of grease on the o-ring will help to keep it from moving during install. I also wrap the metal press reach cylinder in a rag or whatever to avoid bumping into the magnets. Awesome tutorial!

@lonewolfszc 5 лет назад

Sean looks and sounds a fair bit like Michael Ironside

@chadwickwicky67 5 лет назад

Awesome! Question the SKF bearing runs almost $100 ea. I have no problem paying for quality but say vs Burris highly touted ceramic bearing at $32 ea. Is the Burris a viable option? That is a massive price difference so just curious. If the SKF 2RS bearing is that much better than so be it but just curious between factory bearings and SKF is there viable option that’s not $100 each??

@mygiguser 4 года назад

What is the size of the rubber rings?

@eevees 4 года назад

They're about .9 inches

@Tearithin77 5 лет назад

where is this being done and is he open to the general public for onewheel service???

@eevees 5 лет назад

Tearithin It’s being done at Sean’s place of employment in Abbotsford, BC, Canada. He does it for members of the OW community here once and a while but not the general public.

@300zxdriver 5 лет назад

How much does onewheel charge for this process?

@eevees 5 лет назад

They usually replace the motor which can cost $400-$600 I believe. I don't think their repair guys even know how to change the bearings as they usually come pre-assembled with the bearings already installed.

@MikeDQB 5 лет назад

@@eevees Very interesting. So if I try this and screw it up [because it was needed] - I'm only really in the hole my time and the bearings - because worst case I'll need a new motor either way.

@baltod4978 4 года назад

Could you link those tires please? They look amazing!

@eevees 4 года назад

www.shreddlabs.com/tires./

@mripodhelpr 4 года назад

Thank you...Fingers crossed I don't have a press.

@exinoque 5 лет назад

I can definitely tell my OW+ is less smooth than my friend's with fewer miles. Would you know anyone in the Los Angeles area that could provide this service? I like to get this done since I need to take it apart to replace the tire anyway.

@nicholasross5265 5 лет назад

Yes, I am offering this service for people in Socal. Here is my reddit post with more info: www.reddit.com/r/onewheel/comments/aszqc8/socal_maintenancerepair/

@Reedith 4 года назад

I can for free. It's fun

@gunsite45 5 лет назад

Also, are those new bearings pre-lubricated? No need to open the seal and grease inside prior to install? Will adding a few drops of 3 in 1 oil from the exterior once a month be a benefit to extend bearing life?

@AG.Floats 5 лет назад

All bearings pretty much come pre-greased. No need to oil. Oiling it can thin out the grease on the inside and cause premature wear.

@benkitesurfs 5 лет назад

Those were sealed bearings - they are designed to keep dirt/liquid out, and grease in

@MikeDQB 5 лет назад

I don't have an arbor press large enough to accommodate the wheel and I don't want to heat the wheel in the oven due to the magnets. I'm not terribly concerned about removing the bearing but when it comes to getting the new one in there. I figured I could put the bearing in the freezer overnight to shrink it down a tad and make things easier - but do you have any other tips for somebody wanting to do these without access to a large arbor press? I could use a different 12-ton press I have access to but I'm a bit worried I'll crack the housing on the wheel or the plate.

@mcsebbs 5 лет назад

That’s a nice arbor press! Could you heat the hub with a heat gun and freeze the bearings to just drop them right in?

@feliciano1358 4 года назад

What is the actual size of the bear?

@brahamyoung1951 5 лет назад

Circuit boards..any idea where I can get a. ROHS Ru94U0 E253642Y-D..my one wheel stopped when a loose screw rolled onto this circuit board..great O ring tip....thx.

@eevees 5 лет назад

Ryan Witz on Facebook sells brand new parts from taking apart new boards. He could sell you the part. Contact him on Facebook here: facebook.com/ryan.witzhurewitz

@206robert206 4 года назад

Just got a board with 1655mi. Not looking forward to doing this

@jammin2070 4 года назад

Isn’t the 2RZ better?

@jbaker91585 5 лет назад

I've been looking around for those bearings you have in the vid but none pictured are green...

@nartmot3236 4 года назад

go to the skf website and use the link to find an authorized distributor in your area. dont buy on ebay.

@corbinhawkins9309 5 лет назад

I have a OW+ with 1,300 miles. How many miles ho the batteries usually last?

@BradleySpence 5 лет назад

I'm no expert but you can probably go another 1200 miles and still have a good battery. You might notice it starting to keep around 80% of it's charge at 3000 miles.

@chigzypatel155 4 года назад

@@BradleySpence The + uses LIFEPO4 cells which have a lifecycle higher than most lithium batteries (around 2000+ charges) so based on that, I believe around 12000 miles and you may see battery degradation. That's providing the batteries have stayed within there voltage range and no issues related to the Battery Management System have occurred. I hope this helps :)

@BlackSheriff84 3 года назад

What size bearing press is needed?

@eevees 3 года назад

3-ton... not for power but for the size in fitting the wheel/hub in.

@marshallkok5267 3 года назад

I have done 790 miles on my XR and now when I go across a bumpy grass field I hear a bit of a rattle coming from somewhere do you think I should replace my bearings now.

@eevees 3 года назад

The rattling is likely coming from your headlight cable bouncing around and not your bearings. Bearings tend to make a clicking (when going from heel to topside) or grinding sound if they are bad.

@Tech-86 4 года назад

If you give me a dimension I can get you orings for that project.

@Papa_O.A.M 4 года назад

Where do you bring/send your board to get this bearing mod done? I have the bearings but I'm not sure who/where I can get them installed.

@eevees 4 года назад

Go to stokelifeservice.com to find a service centre near you.

@Reedith 4 года назад

Also what's a reliable source to order these bearings from?

@nartmot3236 4 года назад

go to the skf website and use the link to find an authorized distributor in your area. dont buy on ebay.

@ken-mb5cp 4 года назад

I have 2000 miles on my pint. Bearings seem smooth. Should I change bearings?

@eevees 4 года назад

You're probably good if they're still smooth. Future Motion doesn't always use the same bearings so you might have got a good set.

@ken-mb5cp 4 года назад

Also sometimes it seems I’m getting earlier pushback. Does heat of the motor effect this ? Maybe in hotter weather or going uphill?

@eevees 4 года назад

@@ken-mb5cp You shouldn't get pushback earlier. The heat of the motor or heat outside shouldn't affect it at all.

@ironchef3251 5 лет назад

Does the XR use the same bearing size?

@eevees 5 лет назад

Yes. This was an XR. The Plus and the XR have the same bearings and motor.

@JeffTheCSCS 5 лет назад

Are these the same bearings (replacements) as the ceramic hybrids craft and ride sells?

@eevees 5 лет назад

Jeffrey Jenkins No, these are not ceramic bearings. These are much more expensive but worth it. Ceramic isn’t the most ideal bearing type for the Onewheel

@JeffTheCSCS 5 лет назад

pricey, but worth it I am sure. $99 each on amazon sound about right?

@eevees 5 лет назад

@@JeffTheCSCS Yes, that sounds about right. Just be care because there are a lot of fake SKF bearings out there.

@JeffTheCSCS 5 лет назад

Any way to determine a fake other than price being too good to be true?: I. E. www.ebay.com/i/323379729290?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=323379729290&targetid=313776934696&device=m&adtype=pla&googleloc=9007533&poi=&campaignid=1669934606&adgroupid=65058347459&rlsatarget=pla-313776934696&abcId=1123856&merchantid=112286088&gclid=Cj0KCQjwgezoBRDNARIsAGzEfe6TxqyVXKPNVsQ4KyUiupGW2GXxDIV5viaPz6m2X_17ozfVVoLNGFYaAlHKEALw_wcB

@JeffTheCSCS 5 лет назад

@jose350794 4 года назад

Has anyone changed the bearings to a v1?

@feliciano1358 4 года назад

How can I get to you to get my bearings changed?

@eevees 4 года назад

You can check www.stokelifeservice.com to find a Onewheel service centre near you.

@wizrom3046 4 года назад

You dropped the wheel out easily but didnt remove the footboards or bumpers or side rails. So why do all the tire change vids show them pulling the whole Onewheel apart to get the wheel out?

@eevees 4 года назад

Wiz Rom This is also possible, you just need to take the handle off. As mentioned by Jeff early in the video he says that he’s only done a few changes and there might be the odd unnecessary step or two.

@wizrom3046 4 года назад

@@eevees Thanks man! 🙂

@jimludden5440 4 года назад

Mcmaster Carr is where this thing came from

@Clever_Motel 5 лет назад

What do you charge for this service if needed?

@BradleySpence 5 лет назад

We don't neccessarily have a service for this. This is just to show you how to do it yourself. Where are you located? I might be able to source someone that could do it fot you.

@Clever_Motel 5 лет назад

@@BradleySpence I live in the Portland, Oregon area. Just bought an XR and want to make sure I can get these things fixed if needed

@scanshift 5 лет назад

Tell Sean there is a side business for individuals to ship him their boards and get their bearings changed. Price is not really a factor, it is the quality work that he does. Please ask Sean if he is interested. Thanks.

@lazaro.raulponce2984 4 года назад

Good

@xzendersjet7595 3 года назад

Why does the board nosedive at 23:35?

@eevees 3 года назад

I had an aftermarket concave pad on it which causes sensor issues.

@xzendersjet7595 3 года назад

@@eevees Thank you for replying. We just got a One Wheel XR, and on three instances have had a very low speed cutout that looks just like yours, and we have a third party rear concave pad. Never at any type of speed, I think once you are moving forward it will not shut off for thinking a foot has come off. Did you fix it? We are going to tear the whole thing down soon to be sure everything is connected right

@eevees 3 года назад

@@xzendersjet7595 It’s just a beginner mistake most likely. If you don’t have your front foot completely flat and the weight distributed on both sides, it will disengage on you. I teach a lot of new riders and it’s a common issue. I recommend wearing flat soled shoes like Vans if you don’t already. It helps a bit.

@xzendersjet7595 3 года назад

@@eevees But it ignores one side off at speed?

@SgtBarrel 4 года назад

Instead of wire brushing the threads why not just boil the loctite off? Thats what I do with knife pivots

@bitwhyze 5 лет назад

I feel like he's gonna get a copyright strike from playing twenty one piolots morph in the background

@bdog8563 4 года назад

I was looking for someone who heard it too 🤣

@j8ffshin329 5 лет назад

After watching this, I changed my mind & will get a eboard instead.

@BradleySpence 5 лет назад

Jeff Shih What? Eboards have way more mechanical problems than Onewheel’s. Our local dealer sells 1-2 Onewheel’s each day and has never had any issues with any that they’ve sold yet they have eboard issues all the time. Have fun missing out.

@j8ffshin329 5 лет назад

@@BradleySpence from this video I see an oring manufacturing defect, compounded by availability issue, motor damage caused by worn bearings that is not serviceable without a bearing press. For a product that is almost $2k, I'd expect better design.

@BradleySpence 5 лет назад

Jeff Shih You think other eboards don’t have their manufacturing problems? It takes a quick search to see all the issues with Boosted and Evolve boards that are actually life threatening. Also, since posting this video, Future Motion upgraded their bearings and I haven’t heard of newer boards having o-rings breaking. Also, many have have changed their bearings without a press.

@ChrisLeeX 5 лет назад

@@BradleySpence "Also, since posting this video, Future Motion upgraded their bearings" Any proof of that?

@wizardmix 4 года назад

I'm sure you'll be happy with it but damn trying to ride an eboard after the onewheel feels like driving a 95 honda civic after just driving a rolls royce phantom except the onewheel has the maneuverability of the civic and the civic has the maneuverability of the phantom.