No video :(

How to change the Serpentine belt on a Nissan 5.6 Titan, Armada, and QX56

Подписаться 38 тыс.

Просмотров 68 тыс.

50% 1

This procedure should cover 2004-2015 maybe further Nissan 5.6l engine in the trucks and SUVs, it may also apply to M56 or other 5.6l cars.
Weekly Training Available at www.Patreon.com/KeithPerkins
Check Out My Amazon Store HERE:
tinyurl.com/yc...
Some other tools I use:
Launch Diagun IV X431
amzn.to/2SVxG27
Autel Elite
amzn.to/2MfabON
SDT-206 Smoke Machine Kit
amzn.to/2FyLQm1
Redline Smoke Fluid
amzn.to/2MbfKhv
PicoScope 4 Channel Kit
amzn.to/2Mfcy49
Hantek CC-65 Low Amp Clamp
amzn.to/2T4w9Xm
Hantek CC-650 High Amp Clamp
amzn.to/2RVgGeW
AESWave Uscope
amzn.to/2Fw4Fqx
VVDI Key Tool
amzn.to/2SXa4Ky
FLIR ONE Thermal Imager
amzn.to/2MbcjHo
Streamlight ProTac 2L-X
amzn.to/2VVq0yH
EBL 18650 Batteries
amzn.to/2Mbi6gj
Immobilizer Coil LED Tester
amzn.to/2SXHad0
Launch Creader3001 Code Reader
amzn.to/2ROlIdk

Опубликовано:

20 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@jerrykearns6344 5 лет назад

On my 2004 Titan, there are indexing holes in the belt tensioner that allow it to be pinned in the released position. The index holes are shown in the 2004 service manual at page EM-12. So the steps I followed are move tensioner to release position with socket and breaker bar, insert pin (I used an allen wrench) through index holes, remove breaker bar, remove old belt, install new belt, reattach socket and breaker bar, remove pin from index holes, allow tensioner to move to tension belt, remove socket and breaker bar.

@jgwufgator 3 года назад

Thank you, thank you, thank you. My 2005 also has this indexing hole. I found the largest allen wrench that would fit the stationary holen(the one not on the pulley piece). Using this saved me so much time and back pain. I hope I remember how to do this in 15 years.

@dawson91b 3 года назад

Your comment > this video.

@jeuf77 6 лет назад

Thank you for taking the time to create this video. I just finished replacing my drive belt with the help of your video. THANKS AGAIN!

@L1Training 6 лет назад

NO problem, Please like and subscribe!

@MGdriver77 6 лет назад

Thanks for the video! Changed my 2013's today.

@L1Training 6 лет назад

No Problem!

@tjdann64 5 лет назад

Good video. Thanks for your knowledge. You have a nice way of presenting.

@jaybuilder8298 6 месяцев назад

I’m working on a 2020 seems like Nissan hasn’t changed much other than raising the price on the same product, I’m changing mine just because of mileage and I don’t want to end up on the side of the road with a broken belt, it’s inexpensive and fairly easy to replace

@wvtofl 4 года назад

Thanks for video!

@creepingtod 4 года назад

The Titan has the belt diagram right under the hood no need for a diagram on the package

@troykarren6733 5 лет назад

I'm going to assume that the tensioner also had 220k on it. Did you feel comfortable leaving the old tensioner with a new belt? Also the idler pulley?

@Playstation_Sony 3 года назад

I have 2008 armada. trying to figure out how to put on the belt.(after replacing alternator). so I have everything righting down really tight but when I go to put the belt on, tensioner pully last there isn't enough slack to put the belt on. how do you get the tensioner to push down so the belt can can placed over it