How to connect Encoder with S7-1200 ? || High Speed Counter HSC || TIA PORTAL || Lesson#13

PLC Programming Tutorials Tips and Tricks

Подписаться 135 тыс.

Просмотров 93 тыс.

50% 1

Видео Поделиться Скачать Добавить в

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 44

@medosust Год назад

Very helpful especially wiring

@rashidchibvuri2036 4 месяца назад

Great explanation sir thank you.

@ymmijjohnsson 8 месяцев назад

keep up the good work. There are many channels with the Siemens tia portal, but not many that are as informative as yours

@hymdt Год назад

you saved our day with this information ... thanks

@allagomar6033 3 года назад

Thank you so much bro i wish to continu like this video

@thomassaook7787 4 года назад

simple & accurate

@mahmudrajon9104 4 года назад

very good work.

@nirutg5130 2 года назад

Thank you very much

@botas82 3 года назад

Great vídeo, thanks a lot.

@tarekmohsen7572 3 года назад

Thank you

@gilbertopadovani 6 месяцев назад

Thanks for the explanation. Could you tell me where to buy the Seiki CB2000-HC encoder? I tried searching but without success. Thanks in advance.

@pajur 3 месяца назад

Why is Z signal connected to I0.2? Does it have any sense here? According to S7-1200 manual, only A/B signals are needed.

@rincebaby145 7 месяцев назад

Nice video.but how we get reset input the encoder

@electromecanica_automatismos 2 года назад

By the way...in this wiring diagram I suppose that your Rotary Encode is NPN output (If not --- PNP--- M (0V) must be connected to 1M.... that`s right?)

@tourdhorizon97 3 года назад

2000 pulses per Revolution, how is it possible for this small encoder ????

@shameehaajmal1517 2 года назад

Great video! Can I know why all three encoder signal wires are connected to the PLC?

@EASYPLCTRAINING 2 года назад

Good question! three wires to detect if the encoder is moving in CW or CCW direction

@ahmedrezk2281 4 года назад

The jumpre on L+and1m error

@sarpturker5034 3 года назад

Good tutorial. But one think i cant figure out. Where is the Orange cable Z-phase I0.2? Cant see it in Hardware Inputs?

@EASYPLCTRAINING 3 года назад

Yes its i0.2

@rokibhasan2823 4 года назад

Can i change the input in monitor mode without using encoder??

@kingofthering1224 8 месяцев назад

why the counter value reach out to 1700.....??? it must be 1500 only ??? I'm right

@decentmkiza8570 4 года назад

Can you do a video of a stepper motor connection and programming

@EASYPLCTRAINING 4 года назад

I will try to setup ....

@decentmkiza8570 4 года назад

Thanks i am working on s7 1200 1212c ac/dc/rly that would be very helpful

@karoliczanwojtylanu 4 года назад

@@EASYPLCTRAINING Yes, it would be great!

@MaterieUltimeUnofficialChannel 4 года назад

why +24V is connected to 0V?

@mohamedayman790 4 года назад

@muhammaddanishhameed9865 3 года назад

Bhai, encoder se motor ka rpm kis tarah calculate ka sakta hein siemens mein

@EASYPLCTRAINING 3 года назад

Calculate no. Of pulses in 2 seconds and multiply with 30 to get rpm

@muhammaddanishhameed9865 3 года назад

Thankyou

@yadavsaroj1657 4 года назад

Sir please same program in omron plc cx-program

@vorapobautomation9760 4 года назад

How about S7-1500 HSC ?

@balajisekar2071 3 года назад

How to connect two or more encoder in one plc

@EASYPLCTRAINING 3 года назад

You can install encoder input cards with the plc

@desifiedCanada 2 года назад

How to reset count value ?

@EASYPLCTRAINING 2 года назад

Move zero in the data register

@desifiedCanada 2 года назад

@@EASYPLCTRAINING is there any option for external reset ?

@EASYPLCTRAINING 2 года назад

Connect a push button with the PLC, use thus push button signal to move the zero to the encoder data register

@desifiedCanada 2 года назад

@@EASYPLCTRAINING should we move zero in IW1000 or QW1000?

@ghouseahmed4u 2 года назад

@@EASYPLCTRAINING can we do like this - "Since pulses are DInt format, after counter finishes counting until 2147483647, then can i move "1" to ID1000 directly, so that the cycle repeats?