How to connect LED STRIP to speaker(BASS) 

He connected it to his stereo system

right

Ja Moin, dich sieht ja man überall😂

@@marcel7036 Ja normal. Sowas wie hier geht auch nicht. XD

@@Speakershocker ja geht auch nicht, teure Verstärker schalten da schon automatisch ab

@@marcel7036 bei so einem Unfug aber auch nicht immer.

@@Speakershocker kannst du mir erklären warum hier der Verstärker kaputt geht? Kenne mich jetzt nicht wirklich aus aber wer nicht fragt bleibt dumm... Wenn jetzt theoretisch die Gesamtimpedanz über der Minimalimpedanz des Verstärkers liegt (z.B nur die LEDs ohne Boxen) fährt der Verstärker doch auch nicht ins Clipping. Dem is dass doch egal oder? Oder weil der Strom jeweils immer nur ne halbe Periodendauer fließt weil die LEDs während der negativen Amplitude sperren? Was schädigt hier dem Verstärker? Danke

Please give links

Yap :))

How....

@@mathwins7953 so if i have a 1973 Pioneer amplifier does it work?

Why?? Could you please explain me?

Exactly because I tried it and I blowed my amplifier too... Please don't try this

para mi si

Is there a way to do it

Hahaha that is funny, thanks!

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-jABI0uKtpKE.html

They wont blow up but they will die

Bigger resistor, you only need a tiny amount of power from the signal and 600w will blow these up. (I think) if you have an amp that does 600w @ 8Ω then it will do 300w @ 16Ω, 150w @ 32Ω, ...... 16w @ 128Ω, 8w @ 256Ω - measure the resistance of your strip and make up the difference in impedance with another resistor inline to bring it up to the correct value. I would check the rating of your amp first, if it is actually 600w at 8Ω or 4Ω or whatever, from there you can extrapolate where you need to get to.

@@leeknivek it will work I’ve done it to amps that push out 1800 watts 🤙🏽

I am 12 but....same 🤣

@@ConstabeastYT i am 13 and i do this things for 5 years now

@Teodor Vranchev i like mostly computers and speakers

@@CH-FOUR same

Evet bass'a bağlı

I knew it but I don’t do it. Cut is cut

@@paulybeatz3688 I know man but honestly it drives me crazy when I see someone wasting material like that..

Cost bro 🤧

lol?

Yeah, TexasXplorer youre right

it did not burn the amplifier

@@paczkos545 not immediately but it will

Why? Pls show me i dont understand

What? You know this is a 3 way speaker yeah? So all 3 drivers would be affected not only the woofer (or sub as you call it even tho it's not). You are mostly just burning out the amp.

@@jomann3213 you can have a woofer with only medium and hight frequencies on it... what are you talking about? sub is a professional term to define lower frequencies under 60Hz that is even the frequency that electric current flows, besides, that kid also named the video about BASS , and no... not all frequencies are afected the same simply because the amp sends much more power from the crossover to deliver in the speacker the low and sub frequencies, than for the highs frequencies. If you use old lamps, you will see that they dont move much with the highs of music almost nothin but do a lot with kick drums and sub bass. for you to hear from a speaker tweter 15000Hz you need 300 times less energy from the amp, than the energy you need, to hear a Kick sub on theyre usual 50Hz frequencie.

I don't recommend it at all, but black is usually negative, use a battery to be sure

This is RGB(red ,green,blue)led strip 12V, so I can change colour by connecting different wires, but you can use one colour led strip that's more simple.

@@AVmake but what if the sub is in the amp and only tweaters are out of it ...

bro this is fake ;/

@@elektromicha6777 - Seriously? Do you even know what you are talking about? I did this with a car headlamp bulb when I was 13 on Dad's old Aiwa AF-5090. Lucky that it didn't fry the amp., should have added a resistor. However, it worked! Stuff your mouth with your old socks before you call it fake.

How?

@@gameboy1984 Drains too much current from it to light up leds

@@davidluptak go on

@@Kanoshe Amplifier is for speakers with definitive ohms and if you add another appliance like leds than mosfets or chip may burn up from excess current

@@davidluptak 4 ohm speaker is a much bigger load than those few LEDs

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-jABI0uKtpKE.html

are they just callef LED drivers?

@@gothangel6221 i think they are called Arduino Uno LED Sequential Control

How?

yeah apparetnly you gotta have like arduino's and coding to make it proper

​@@Kanoshe you can use a spectrum analyzer board

Somebody got his big boy pants on all by himself 😂

Yo I've been searching for shit like that. Every tutorial or led light kit seems so basic.

Si le das más volumen no se queman decasulidad

DON'T TRY THIS

Bro I know it how to work set up I know operator I know

@@johnlloydcabacungan5717 Get a 1.1k resistor and connect directly to speaker

You will blow up the amplifier if u do it. Please dont.

Don't do it!

Is everyone here just to tell people not to do it?