No video :(

How to Connect Speaker Wire to RCA Plug - 3 Ways!

Подписаться 93 тыс.

Просмотров 110 тыс.

50% 1

Step by step tutorial showing you how to connect your speaker wires to any RCA plug. I will show you 3 different ways. Most people are looking to do this to connect their speakers to a home theatre or receiver amplifier.
↓↓Amazon links↓↓
►Wire Stripper 10-22 AWG Wire Splicer : amzn.to/48QWjU4
►Speaker Wire Cable to Audio Male RCA: amzn.to/3HgB7LB
►Bare Wire Cables to RCA Plugs Adapter: amzn.to/47sgTch
►16-Gauge Speaker Wire Cable, 50 Feet: amzn.to/48ThOnr
The Amazon links above are affiliate, which means that I may get a small commission from them if you decide to buy something on their website. This is to support this channel :)
Don't forget to like and subscribe if this was useful to you!

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@justaguy4real 4 месяца назад

Good job buddy, I learned something new.

@chrispilkington7612 3 месяца назад

It makes a difference which wire is used when you are splicing the speaker wires into the RCA plug. Speakers have phasing and you need to make sure that the negative or positive in each of your splices is identical.

@guanedits6349 3 месяца назад

Oh my nagative wire is bigger than my power cord' could that be the reason why its not working when i connect it to my deck?

@IanGorillatag-wq6sf 6 дней назад

Thank you, Cuz. I am trying to wire up two megaphones too a Bluetooth receiver.

@charliewilson3369 2 месяца назад

Thanks, it works but it doesn't sound that good. But it will get me through until I get some better RCAs.

@vicmurai1033 5 месяцев назад

Thanks for your advice and help.

@sackiteylawrence 11 дней назад

Thank you!

@Greenbluesforever-yj3el 2 месяца назад

I have one problem one of the RCA output connectors on Marantz CD63MKII original SE is not sending the sound signal in the left speaker, when I move the cable's lug up the sound appears in the left speaker, when I released it the sound dissapears, please I need an advice how to repair this since I am not an electronist.

@jianliu7516 3 месяца назад

The wire inside the RCA is too thin. just buy the RCA to speaker wire adaptor can save your time and money for the RCA cable

@rhodagunn5075 3 месяца назад

How does it save money if you have to buy it?

@jianliu7516 3 месяца назад

@@rhodagunn5075 The adaptor is cheaper than RCA cable, and you can easily connect the thicker wire for better quality

@rumourplays 3 месяца назад

Lol@@rhodagunn5075

@tommyfalconey Месяц назад

When your speaker wires are coming directly from a record player for example, you can't

@VisualReality801 29 дней назад

@jianliu7516 no shit stupid ass but that doesn’t help if the late at night

@vicmurai1033 5 месяцев назад

Are the two wires negative & positive wires from each speaker? My amp has 4 jacks in the rear. Can I plug any of the 2 RCA plugs into any of the 4 jacks ?

@osopena3979 3 месяца назад

Double check your RCA's. Some amps have double inputs while others have input and output. Never mix your input with output.

@blazebott 4 месяца назад

worked for me☺

@0rurin 4 месяца назад

I'm a bit confused, I thought you need to break up the two cables into two plugs, since there are one connector for each, the positive and the negative end. You can just connect both to a single male plug, and leave one of the two connectors empty?

@Hans57116 4 месяца назад

Im confused aswell, did you find answer?

@Jairoalvarz 4 месяца назад

he shows it near the start. each rca cable runs two wires! The two wires that go into a speaker are just voltage and ground. You use 2 rca cables (red and white) because you have left and right

@osopena3979 3 месяца назад

@@Jairoalvarzright so in terms of using subs or other speakers in pairs. Wouldn't we use both RCA's instead of wiring them down to a single plug?

@GHHF666 2 месяца назад

Stupid question: does this also work the other way around? Would it ibe possible to connect a denon AVR front speaker output via speaker cable directly into an stereo amp (analog input RCA)? Would the volume level be higher if taken directly from the amplified speaker cable signal or would it be converted down to similar effect as when using pre-out RCA? Could this damage either amps or would this just fail...?

@AnExtream-introvert 6 месяцев назад

Good work

@dalilamuhammad1309 4 месяца назад

Good job, thanks

@neilyhodgins3320 3 месяца назад

very good

@gRosh08 5 месяцев назад

Cool.

@user-rb8wy6du4n 3 месяца назад

What if I have 1 sub output that is rca and my sub is red and white wires?

@jhrochester Месяц назад

Red and white just mean left and right. So if you run your sub off one input, you might just get left. Or righr

@jhrochester Месяц назад

You would wire your other side into the opposite color, and have Left and right red and white

@blazebott 4 месяца назад

works.

@Marvin_On_Stars112 7 месяцев назад

Nice

@TricksTipsFix 7 месяцев назад

Thanks

@canniloni 5 месяцев назад

hi! do you know what to do when there’s absolutely no information on what Ω my tv is? my speaker is a 6 Ω edit: i found the manual for the TV (which is very old, from 2008), but i’m not sure what to look for because the manual doesn’t mention ohm in the audio part, it says “output power 10 W + 10 W”

@bytarik Месяц назад

I don't think your TV output is enough to power speakers without an amp. Best to do is just buy a small amp(something like a class t amp) and connect the tv to amp. Then you can connect your speakers to the amp.

@canniloni Месяц назад

@@bytarik thank you so much for the help, i appreciate it :)

@bytarik Месяц назад

@@canniloni Yeah no problem.