How to do Electrical Troubleshooting of Electrical Motor Control Circuit 

This simulation software is no longer sold to user as per Bin95. Now, they only sell it to school only. I really do not understand why bin95 do so.

Im an industrial mechanic and at work I had many loose wires and broken wires that I had to troubleshoot over the years , great video Im heading to the website rite now , thank you.

Very detailed and yet simplistic enough, not to mention interesting. Thank you for the video!! 👍🤝

Disconect outgoing motor cables from the main Control panel and check out resistance values of the 3 windings , They may be an open or high resistance reading on one of the motor wires or one of the motor windings may be unbalanced, , this procedure will tell you if its an external problem not an internal Control Panel Problem .

That was a very professional diagnostic procedures, and also a safe one too.

Can someone please show me how to download this simulator so that I can practice this on my own?

I used this program in college, it sucked to do at the time because on the surface it’s not a very fun application. I learned a lot about circuit failure and in my experience I’ve found a lot more loose or burnt connections that I would have thought.

how to download this software ??? and how much it cost ?? if its free please send me the link thanks

how to download software

If you are impressed buy this video you need the correct training as I’ve never seen anything so dangerously stupid. The overload trips so do a live test by pushing in the overload. Look guys and gals airstrip isolate the supply with a permit to carry out your testing, test from the top side of the 1st fuse to 1, 2nd fuse to 3, then 3rd fuse to 5, if ok, test across your contractor 1 to 2 then 3 to 4 then 5 to 6 by pushing the contractor in so you know you don’t have carbonised or worn out contacts, you can do the same test across the overload if you reset it, if all’s good turn your meter from continuity to the low reading ohm setting and remove the motor wires from the overload and test between the wires what was connected between 2-4 then 2-6 then 4-6, all the the test so far can be done with the low reading ohm meter and should be roughly the same even by testing the fuses and contractor the readings should be alike or you have found a dry joint or defective components, if the motor is not balance in readings test inside the motor terminal after removing the brass star/delta strap bars U1-U2, V1-V2,W1-W2, to identify a faulty phase. What if it test ok? Make sure the motor rotates by hand, get a big screwdriver stick the handle against your ear and the other end near the bearing and turn to hear if the bearing is grinding. Replace/repair the faulty part. Now do the live test after obtaining a live working permit. Doing a live test 1st can cause the motor to burn out by overheating it can even rotate on two phases with reduced torque and then burn out. Ammeter readings can be taken on the run test or condition monitoring. To find a fault a dead test takes a few minutes the longest part depends on the mechanical connection, size and position of equipment.

Simple problems like this may cause a lot of money and time if not troubleshooted properly. Great job there! Nice vid.

Faster would have been to tag out the main breaker. Pull the fuses. Check fuses, then check each phase to the others, then test continuity of the problem phase.

The FPS 3000 is an excellent training video. I have the older version which simutech no longer supports and does not sell to individuals. You have to go through your company if you want the new training software. It uses real world simulation and plenty of practice faults, Also includes some genius practice faults. That will definitely test your troubleshooting skills to the max. Safety is a very important part of this course as you will see when going through the exercises.. I highly recommend this real world training software course if you enjoy diagnosing and then repairing the equipment to its fully operational status.

Sir What software tools do you use to practice Animation?

I appreciate detail oriented video like this. Great Job

great content, I learnt a lot.

Pretty cool video. But a loose wire as in this case would likely have been significantly damaged by running under load.

Everyone who liked this video will also enjoy playing the free online electrical troubleshooting simulation game at bin95.com/industrial/electrical-troubleshooting.html

You ran the system up to the point where the agitator would not operate because of a open in one leg of the power circuit, you then found the problem in the power circuit, repaired this problem and re-energized the system. Why didnt the agitator immediately start operating once you re-energised the power circuit, as up to that point everything in the mechanical and control circuit would have been satisfied? Just saying!

So if im trying to troubleshooting something for open and it show like .3 ohms and then it drop to zero ohm and stay at zero is that good or bad?

Jones Patricia Jackson Timothy Jackson Frank

what program is that. can I download it

Why drain the tank the second time..? no fucking sense... just run the agitator and save the product.

Fuck yeah , youtube tryna send me signals to go and become an industrial tech 😂

Thank .....very helpful video...Can you give me the link to get the simulation software.

Great training program , Then they stopped making it available for home use.

I would love to have that test board on an app

Very Informative video...animation and elabortion fine...thanks Dear

How i can buy this software.. i was in the site. but i dont understand how to buy as a privet and not as a school..

guys please give the software and download this video,,,thank you

you forgot to call the control rm operator and tell them you were putting it in local control.

how to download software

Very useful, and appreciate for the attention to details.

Who turns off the breaker when placing leads?

very good ...helps a lot

great job. thank you

Hi bro, how can I download this software🙏??

Kya hi po

Wow nman congrats 👏🎉🎁

Hi, I like your lecture. Thanks

I have a software but forgot log in password. Is there any way I can recover. Please help.

this video giving me an idea and learned me a lot.

nice

Great job on the video

What is the music in the beginning and the end. It kicks ass man. That shit is rockin.

Very interesting. But the flaws that I thought were wrong. 1. Before resetting any safety system, it is better to find the cause of the reset and after fixing the problem, proceed to reset the overload. 2. To control a problematic circuit, it is better to start from the load first. Engine resistance. Resistor to contactor. Next, the voltage on the contactor input and then by labeling the motor wires to control the voltage arm on the terminal. 3. After controlling the whole system, after resetting the overload, the motor should be energized.

Can we start 75hp motor with direct in delta

where to buy your software.her in Philippines

شكرا شكرا كدة يعتبر نت نافع للشباب

Well explained

cool software.

Nice video

Awesome training video. I learned a lot from it. Thanks.

cool video

good work

What is the parogarm name

I work on this type of stuff everyday at my plant. I always test a fuse from one end to other end. No tone on meter. It's bad.

👍👍

Where can I find like This videos

Hello. Is there a copy of this program for Android or any similar software for industrial electricity?

5:21 you have measured the resistance from the contactor to the terminal block and got 0.2 ohms but the overload was still tripped wchich means that you shouldnt have a path.

what software is this??

what is the program name please

were do i get this one?

What´s the name of this software plz?

good

test

Great ! Thank you !

well done

Hello

excellent

cool

excellent

EK number!!!

This would be perfect for me right now. I’m just starting out as a maintenance tech. I understand the basics, but I need to get some experience with troubleshooting and then move into PLC training. Can anyone here recommend anything for me like this. I don’t have the opportunity to pay or get any schooling right now.

exact name of this software plz?

It exist mobile app?

What is the sofrware name

collect

this is sick