How to fix Samsung washer with 4E error code 

Thank you very much from Canada! 👋👍👍The worn tube was our exact problem as well. Had to take the front cover off to remove the entire hose to fix it properly, but that did not take very long.

My Samsung washer drain out the soak, spin a couple minutes then drain out everything and fill up water again to finish washing cycle, it is actually wash without soak, no error code, wtf! After I saw this video and find out there was a hole on the tube, I used silicon to seal it , boom back it business again THANK YOU Mr Hameed!

Thank you so much Mr. Hameed. I kept getting an LE error, so I figured I had a faulty pressure switch. Upon replacing, I got a 4E error which left me scratching my head. The tub kept filling with water but wouldn’t start a wash cycle. That’s when I found your video. My pressure switch hose was also torn. I wrapped it with some tape as a temporary fix and voila, my washer is working again. Thank you so much again Mr. Hameed and best of luck to anyone else having this issue.

Thank you Mr. Hameed, use the tip and worked perfectly. Use a plumbing coupling and Saved me $200.00. Thanks Again.

Sir, you saved the day!!! It was exactly my issue! I put a Butyl putty tape as a temp solution. Works like a charm! Thank you, again!

Thanks Hameed, this was so helpful. Post a donation link so I can buy you lunch. For anyone doing this repair I have a few extra tips. -Cut the hose right where it's worn through, and bridge it with a sleeve that is rigid, about 1" long or longer, and 4-6mm OD, with hose clamps. I found a plastic tube in a bic pen that worked. I'm not ordering a new hose, this fix looks reliable to me. -Dont re-attach the hose to the outside of the washer tub, that's why it wore through. Just tape it to the dryer wall, so it won't ever rub again. -IF your vacuum hose is not worn, and you have some other cause of 4E error code, consider this: While checking the electric valves with a multimeter, even a working valve will only show voltage there during the short moments when the program calls for that kind of water. So set a program that asks for hot and cold, and be patient waiting for the moment that water is asked for.

Thank you so much mr.Hameed, this worked perfectly! I fixed it myself instead of spending 100$ on it. Although i couldn't find a replacement for the hose locally, so i patched the hole with red thermal silicone, and it worked just fine 👍🏻

Great Job! The scary part of the entire video is that Hot Water Tank Exhaust starting at 10 minutes into the video! It goes up a little and then goes downhill! Scary!!!!

Thanks you saved me money and time...exactly my problem!!

Thanks for useful video Hameed. You mentioned during the video that you had done a different video on testing the pressure sensor but I can't find that video. A link would be super handy 🙂

You noticed the pile of black rubber and solved the mystery. That was fun to see.

Thanks you for Really helpful information🙏

Your videos are great thank you for sharing. I have a Whirlpool washer that does not drain fully. I replaced the control board but the problem is still there.

Thank you!! I forgot to open water line back up.running like new amazing RU-vid

Thank you very much! It helps!!!

Really Helpful. Thanks!

Thank you!!!

I can’t find any video on how to replace the pressure hose 😢. I have the hose but don’t know how to replace it on my Samsung front load. Yours says from the back but on my model there is no where to access the hose

Man, you made my day!

I replaced the inlets hot and cold, no kinks, also replaced pressure switch. Still getting 4E but it’s filling with water completely. Pulled hose and didn’t notice any holes. One small spot with wear but no hole. What else am I missing?

mine display panel has a red key logo , its blinking , what does it mean ?

Really Helpful. Thanks!