how to fix the speedometer on subaru legacy outback

Подписаться 62 тыс.

Просмотров 80 тыс.

50% 1

www.vehix411.com this video will show you how to repair or fix your speedometer on subaru legacy outback 1996 ,1997, 1998 , 1999 , 2000 watch part 1 to diagnose or troubleshoot the speedometer
~-~~-~~~-~~-~
Please watch: "Vehix411 APP for all your genatic, manufacturer spacific trouble codes and oil reset"
• APP for trouble code d...
~-~~-~~~-~~-~

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 37

@kuna129 7 месяцев назад

:) What do you know, it really works! Thank you! It was a heart-stopping experience to disassemble and re-assemble it all, and I used pieces of bamboo skewer and folded cardboard for the fix - but speedometer and odometer started working after this!

@mrnoah1504 12 лет назад

After replacing my 250 dollar trans sensor harness and not fixing it I stumble across this......... And IT WORKED!!!! thanks man!!!

@rdabvnblo 14 лет назад

Thank you making this video. I have been dealing with this issue for several years now. Snaping the trip odometer button would work sometimes until it broke. Then turning the windshield wipers on and off would get it working sometimes. I follwed your video instructons and it worked immediately. I'll keep you posted if it stops working. Thanks again.

@leightonelliott3140 10 лет назад

I had my subie serviced and tested at a transmission shop and they informed me it was the head unit. I found another "fix" on some subaru forums. It too was an epic failure. I did resolder two connections on my old head unit and speedo has been working since.

@Dobro-Rally 11 лет назад

You should rename this to "How to break the speedo." If you've done all the work to get to the bad connector then do yourself a favor and fix it the right way with a soldering iron. Jamming a screw in there will only put more strain on the joint. It might fix it temporarily, but in the long run its only going to get worse.

@KLOUDZ16 7 лет назад

Thanks for this video!, helped me out alot. i ddnt use screws though, i wedged every gap with cardboard and boom everything startd working! Cheers 😊

@johnstepto6347 12 лет назад

Reflowing the solder connection in the blue connector and the jumper worked like a champ. I hit each with a little flux prior to remelting them.

@Викоша-ю1г 3 года назад

Реально рабочая версия . У меня спидометр заработал . А так по желанию работал . Спасибо автору.

@rodspencer 13 лет назад

4) What you are looking at is the instrument cluster with a clear plastic cover. Things are very-very FRAGILE in there with those dials. Try to keep the plastic on, as the tabs that hold it in are likely brittle with age. 5) There are four more screws to remove. A short (2-3") Phillips head screwdriver is helpful for the two on top. Before you start I suggest you get some packing tape and seal up the now open spaces into which screws may fall. Continues…

4 года назад

What to do if only tachometer doesn't work? It works sometimes for a moment if a catch a bump :D i checked the contacts... Also the obd reader gets the rpm readings all the time, even when the tacho isn't working. Any ideas?

@throttleblip1 5 лет назад

The screw doesn't help anything...you need to take out 5 silver screws that need to be removed and solder a wire between speed sensor pin and j8 on the board

@johnnyvalle5996 Год назад

Thanks bro ill try that in the am 🔥🔥

@andyinmichigan9058 6 лет назад

did this and it worked . i know i should do it the "right way" but it's my backup vehicle at best, so...if this stops working i'll fix it later on

@PeterPug 11 лет назад

I'm having both speedo and odometer issues on my 2010 Outback...is it the same fix!?? Dealer wants almost 1 grand to replace the cluster. Thanks!

@rodspencer 13 лет назад

Arrg! After 2 weeks, the issue has occurred again! This car is used on rough back roads. As soon as I get the car, I will try placing a connector sleeve on that pin. Soldering will be the next step. BUT I'm beginning to suspect the problem is not the pin/sleeve but the connector's connection to the underlying board. Stay tuned.

@davidrojas5087 3 года назад

Thank for your video, but I need help to replace a bulb of dash, in specific, column of change: P, R, D, 3,2,1. I was impossible for me

@S.R.L6600 6 лет назад

Noticed your gas was on e. That's my problem gauge is on e but I have a full tank .I replaced the fuel unit and still didn't work. Any idea what to do? Thanks.

@darrinlee2076 10 лет назад

Does this particular failure set a speed sensor dtc?

@kaskopf 10 лет назад

You know how is can change the speedometer for my legacy gt vdc for the legacy b4 speedometer? I try today,it can conect all sockets but any gauge works. ..

@bunnyson 13 лет назад

yup i tried this today...no luck at all...still dead....damn it!

@guestandsons 10 лет назад

Thanks!

@darrinlee2076 10 лет назад

nevermind, my failure was seized speed sensor in the trans. re-shaped the twisted key and soaking the sensor to see if I can free it up

@GaryHallas 13 лет назад

I just got done doing this,, and no luck,, Didnt work?

@protonspring1 13 лет назад

Yikes. Just resolder the connector on. It works much better for longer. See my fix at fixya.

@silvertailfins 6 лет назад

Really. I would be embarrassed to post something like this.

@leightonelliott3140 11 лет назад

I tried this and didn't work for me. The blue connector was loose and I took the whole module a part to check the soldered connections.

@caseyconiff2302 9 лет назад

How do you get the cluster out of the dash?

@gnavarro1971 3 года назад

Put steering column to the lowest level height regulation. Locate 4 screws, 2 below the headlamp washer, defogger and fog lights switches, and other 2 upwards close to cluster. Unscrew, remove the black mask, unplugging the mentioned switches. Put the mask aside. Locate the 4 screws that hold cluster in place, unscrew. Pull the cluster towards you, slide your hand to the back of it. Unplug 3 large connectors (2 white, 1 gray) and the speedo (blue one). Open driver door, and slide carefully the cluster to your left, passing it through the space between steering wheel and dashboard. That's all!

@jamesblevins4543 9 лет назад

yeah but its a conection that needs to be sioldered how long will this screw last??

@Chicken2341 6 лет назад

You have to think that alot of people do not have the tools or knowledge to solder.

@robertmuckle2985 4 года назад

@@Chicken2341 People like that shouldn't work on their cars! This video is a dumbass fix, done by one of those people!👎

@rodspencer 13 лет назад

1) Start by tilting the steering wheel all the way down. Upcoming steps involve jockeying things out to the right of the wheel. 2) Four screws remove the first outer grey panel with four (or so depending on options) buttons. 3) Disconnect the plugs on the back of these buttons. Continues…