How to fix Toyota forklift brakes

Подписаться 5 тыс.

Просмотров 426 тыс.

50% 1

In this video, watch brake shoes and wheel cylinders get replaced on a Toyota 6FGCU18 forklift. Intella Parts offers a complete range of aftermarket replacement forklift parts for all brands including Toyota, Hyster, Yale, Caterpillar, Nissan, Mitsubishi and many more. You can visit our website here: intellaparts.com
NEW Tool kit. Includes axle nut removal socket and more: intellaparts.com/p/0058986729...
Also visit our page here for a complete list of Toyota brake parts:
intellaparts.com/c/020BRAKE-P...
Parts used in this video (with links):
- Toyota forklift wheel cylinder, part number 47410-11630-71
intellaparts.com/p/TY47410-11...
- Toyota forklift brake shoe, part number 47403-12810-71
intellaparts.com/p/TY47403-12...
- Toyota forklift brake shoe, part number 47405-12810-71
intellaparts.com/p/TY47405-12...
- Toyota forklift oil seal, part number 42125-U2100-71
intellaparts.com/p/42125-u210...
- Toyota forklift oil seal, part number 42415-10480-71
intellaparts.com/p/42415-1048...

Хобби

Опубликовано:

20 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 133

@richardbraida9176 2 года назад

Replacing brakes on my 1988 Toyota 3000 lb lift. Given high cost of parts and labor, my Forklift would have been scrapped if not for me doing the job......guided by this video.

@gregoryruzicka8287 3 года назад

What a great video, no unnecessary anything, step by step start to finish. Whoever made this video bravo.

@jamesguschke9338 11 месяцев назад

I am going to listen to this music next time I do forklift brakes. It really takes the edge off! 🎉

@bikerbri327 9 лет назад

The mechanic featured in this video makes his job look easy (Which it is Not!) because he is talented and has years of experience, and it shows! He really banged this brake job out nicely and really efficiently! Great Job!

@metaxa715 9 лет назад

Biker Bri327 suppose to lubricate entire mechanism using different types of grease in a few certain spots. Practice is needed to apply right amount. Other than that pro.

@chrisl8882 8 лет назад

+Metaxa 7 should have had the drums cut and shoes arcd in as well. this is not a pro. forklift brakes are no joke as this video makes it seem. if this job was done as shown in this video on a truck weighing more than 10k the results would be less than desirable.

@wallacegarrod3528 8 лет назад

+Chris L on this particular Toyota trk, that is not necessary...

@wallacegarrod3528 8 лет назад

+Biker Bri327, he didn't bleed the brakes either.....

@hiyadoingc7993 7 лет назад

@ragingpandasgamehouse7092 5 лет назад

I noticed he used lock-tite on 6 of the 8 axle bolts and Toyotas patented cross-thread on the other two...

@luismorejon660 8 лет назад

Thank you! Really helpful!

@donaldb3628 4 года назад

Amazing,,,,, no adjustment necessary!

@bishopsnake887 6 лет назад

I can't remove that seal till I learn this Thanks man

@tarmonoskw4213 3 года назад

mantap mas bro...tolong diperagakan cara yg mudah bongkar pasang rem forklip Toyota 25,trimakasih

@mrg4598 5 лет назад

He is a forklift brake God

@clayton9136 8 месяцев назад

Oh boy! If only they were all as easy as this one!

@kevindecunha6775 8 лет назад

Very helpful

@luisframirez2 4 года назад

This was so helpful in the job! Thanks

@shemwayman1146 7 лет назад

VERY NICE JOB, THANK YOU.

@wilfredlobo2010 8 лет назад

Speed and quality of job really excellent..

@Simon-gc5cf Год назад

Guess I missed the bleeding the brakes which must be easier with the wheel off. Any tips for a one-man bleed. Most kits I have seen use air pressure from a car tyre and clearly a fork truck has solid tyres. I wondered if I could Mityvac some pressure for into the master cylinder or vacuum bleed at the nipple?

@ur2ndurlast 9 лет назад

Just started working for Toyota Material Handling just did my first brake job looking at getting more efficient

@user-py7jo5mz9z 6 лет назад

full range of services for maintenance and repair of loading equipment baltic-forklift.prom.ua/g2597792-servis-dlya-vilochnyh

@charlesjohnson-qc6hj 3 года назад

What size socket to remove the hub,,, I'll have to buy one,,, looks like a dam 4",,, idk... Can you remember what size they are,,, it's a class 2 lift 5000 lb lifter,,, if that even matters...??? tia....

@fredrezfield1629 Год назад

how did you bleed your brake lines?

@SurajKumar-zw2up 5 лет назад

Good job

@user-ys5qd5rt2t 8 месяцев назад

Really good video!

@johnblack4636 9 лет назад

very nice thanks for the that

@alexagdhf6866 Год назад

Спасибо за видео понравилось жду новых выпусков молодец

@tanjimulhaque7839 2 года назад

Tnx

@jimenz6548 5 лет назад

Appears very simple.... looks like 3/4 ton pick-up truck hubs and standard Chrysler 1970's rear brakes of a car, I would bet they are the same shoes and hardware too....

@intellaparts 3 года назад

Chrysler xref to Toyota? Probably not. Toyota uses Denso, Chrysler 70s probably Allied Signal/Bendix...

@nileshpatil3754 Год назад

Nice job sir

@vanderpoolfarmsl.l.c.9983 3 года назад

Nothing mentioned about adjustment or gear oil replacement.

@aliyahi9982 5 лет назад

Top merci

@fredrezfield1629 Год назад

3:00 did you he swap the wheel cylinders or just clean it? and remove pins?

@AIMone3WP 7 лет назад

What size is that lock nut??????

@gregwomack5237 8 лет назад

thank you - diesel technician: corpus christi -

@frankiedigioia 5 лет назад

Are you not going to show us how to bleed the system.?

@rudypadilla9626 Год назад

I usually replace entire backing plate ( already assembled). Comes with e brake cables Because WHO. Really checks the wear pads on backing plate NO ONE. There Normally worn out It is great instructional video

@andymeza5246 6 лет назад

Very educational video but I need to know the tools that are being used in the video

@intellaparts 3 года назад

Sure! Our guy's tools are ancient but we offer a kit including the socket for the axle and the various spring tools plus bleeding kit here: store.intellaliftparts.com/p/00589867290.html

@Simon-gc5cf Год назад

Is there a video of that brake bleeding kit on the link? Thanks

@nelsonoliveron1881 8 лет назад

sir how dismantle the engine to transmission forklift toyota25

@jamesguschke9338 11 месяцев назад

What is this song??? I love it!

@lizardogil3049 5 лет назад

Gracias por el vídeo, es muy bueno. Quisiera saber el nombre y la medida de la herramienta utilizada para extraer el cubo hexagonal ( la que usa con la palanca en el segundo 57 del vídeo) Saludos desde Caracas Venezuela

@richardbraida9176 2 года назад

I bought that tool, which holds the brake drum in place, from the local Toyota fork lift sales/service center.

@Nelval573 2 года назад

Is this the same as 2FGH14 TOYOTA FORKLIFT?

@Zionsol777 5 лет назад

Any reason in particular that you wouldn't pull the bearings out and Clean and repack grease in them whenever you have the seal pulled?

@Zionsol777 5 лет назад

@TheOtherWhiteBread0 I didn't say to necessarily change the bearings but looking at them in filling them with new grease would not be a bad idea. The Hub that was pulled off has two bearings one in the front and one in the back that are easily removed and packedwith new Grease

@Zionsol777 5 лет назад

@TheOtherWhiteBread0 interesting.....all of the forktrucks i have worked on have had greased bearings.

@Zionsol777 5 лет назад

@TheOtherWhiteBread0 ok....i can agree with that

@brentmacumber362 5 лет назад

@TheOtherWhiteBread0 no its not filled with oil hence the axle seal, and is infact a packed bearing, any good mechanic would inspect the hardening on the bearing cups and condition of the bearing, wash and the repack with fresh grease

@brentmacumber362 5 лет назад

@TheOtherWhiteBread0 yeah. Did you see him change the axle seal which holds the oil back in the diff housing so it cant reach the wheel bearings

@bus2600 6 лет назад

old friend of mine says if you have to use the brakes on a fork lift in a warehouse you are going to fast

@garizaldydiaz5676 3 года назад

HOW TO REPAIR WHEEL CYLINDER BRAKE

@cookiehead2 3 года назад

Do you need to refill the differential after removing the axle shaft?

@dankronenberg946 3 года назад

You should check your level you might need to add fluid it’s 90 weight gear oil

@Nelval573 2 года назад

Do you know what type a 2fgh14 Toyota forklift uses

@fredrezfield1629 Год назад

@@dankronenberg946 do you know how to change wheel cylinder ? i am working on a caterpillar right now the cylinder however is welded to the casting what are you supposed to do ?

@workinprogress3942 5 лет назад

My cat forklift hand brake buzzer stays on after brake is released and driving. Any suggestions

@amilton4849 4 года назад

Cut the wire off.

@jonathanisraelflores5577 3 года назад

Como se llama la herramienta para poner los resortes de sujeta la balata?

@jamesguschke9338 11 месяцев назад

En engles: brake pliers

@LmnChupa 4 года назад

Is refilling brake fluid and bleeding not part of this job?

@dankronenberg946 3 года назад

Yes you will have to fill the brake fluid and bleed the brakes anytime you open the brake line or change your master cylinder will cylinder if you have to bleed the brakes

@MrDouglind 7 лет назад

it's all good when the drum just pulls off easily but if it is stuck on and you have backed off the brakes with the ratchet and still no give,have also pounded on the drum.

@andyfreeman660 4 года назад

Try bolting the drive shaft on to the drum with the shaft sticking out. Gives you a bit of leverage to wiggle thee drum free.

@luismorejon7050 4 года назад

Or try turning brake adjuster opposite way so brakes can open up freely...

@griponinc5605 4 года назад

Is there a spring kit that can be purchased?

@dankronenberg946 3 года назад

Yes you can Purchase the springs and components sometimes are classified as a small parts kit You will need make model and serial number of the forklift

@phillhuddleston9445 5 лет назад

Very good video, very thorough but the music is horrible.

@ai109 8 лет назад

Does anyone know what size the locknut socket is?

@broncoblue83 5 лет назад

3 1/4" 8 point

@RS-lk2zb 4 года назад

Which vehicle is inside this will cylinder? Please tell me brother

@aceforklift4096 3 года назад

Disel forklift Toyota model

@user-nh2fs8zv5y 2 года назад

جميل

@hontro7846 3 года назад

Wow.

@becltd8255 8 лет назад

how to forklift break repair

@charlesjohnson-qc6hj 3 года назад

What size socket to get the hub off,,, looks huge...??? I kinda need to know real soon,,, it's almost apart... Thanks in advance...

@marcelvandentop6694 3 года назад

Tool kit here store.intellaliftparts.com/p/00589867290/toyota_forklift_brake_job_tool.html

@antoniusfrancis3449 Год назад

Whats the name of tools to removal spring pin ?

@ianrobinson9565 11 месяцев назад

If you are talking about the springs that hold the shoes to the backing plate the tool is called a Brake Shoe Spring Compressor. The TOLEDO one is part no. 310256 to suit spring washers 8-24 mm. Hope this helps.

@xwolcliff10x 3 года назад

What socket size used to take off wheel

@marcelvandentop6694 3 года назад

Complete tool kit is here store.intellaliftparts.com/p/00589867290/toyota_forklift_brake_job_tool.html

@AHMEDAHMED-gm4iv 3 года назад

Dee fresh😀😀😀

@fai3704 4 года назад

What s the name of that tool at 1:24 sec to take out the spring?

@jp-jz7ve 4 года назад

You can buy it separately, but that one is mounted on the handle end of a brake spring pliers. www.amazon.com/Steelman-42015-Brake-Spring-Pliers/dp/B07DBZLLM1

@intellaparts 3 года назад

We offer a complete set of tools for this job here: store.intellaliftparts.com/p/00589867290.html

@fai3704 5 лет назад

4:20 sec what is the name of that tool to put the springs in place?

@harleysimmonds50 5 лет назад

Brake spring washer tool

@fai3704 5 лет назад

Thank you very much. Any links where i can get it?

@RV-jw7nb 4 года назад

I'm no big fan of snap-on, but the BT11, BT12 and I think BT8 make these jobs SO much easier. The knock offs fight you the whole time. Other than that, save your money. EDIT: BT12 is great, some are cheap on ebay. BT11 wont fit over a lot of the forklift main spring anchors S6118A is the best spring retainer tool. Really bites in and holds the retainers. The 10mm for the brake lines are kind of soft, I've found that a Flank drive open end really grabs well. Vice grips can get you through as well, if you're careful. Good luck all!

@intellaparts 3 года назад

We offer a complete set of tools for this job here: store.intellaliftparts.com/p/00589867290.html

@vertigoexplendorgarciarami8022 5 лет назад

Fine10

@timemachine2525 6 лет назад

did i miss seeing how he removed the brake line from the wheel cylinder ..everything else seems a lot like standard drum brake job

@timemachine2525 6 лет назад

disregard i see it now i am blind

@larryspivey4813 6 лет назад

Cory M you have to take the cylinder loose first

@hobopiesforeveryone 3 года назад

What was everyone's "farm answer" for the hub wrench? I'm ordering parts as we speak lol

@marcelvandentop6694 3 года назад

Complete tool kit is here store.intellaliftparts.com/p/00589867290/toyota_forklift_brake_job_tool.html

@josefkopecky3320 8 лет назад

na všetko nám treba špecialistov

@thetruthonlythetruth9362 Год назад

DUDE !!! Show how you Bleed the wheel cylinder. HUGE PAIN IN THE ASS bleeding the wheel cylinder.

@ryanvandeburg365 Год назад

Yeah, do they use hydraulic fluid for the brake system. Or do they use brake fluid like cars?

@dwightPhoenix 5 лет назад

This guy works without a glove....

@mikewatson5457 4 года назад

dwight Phoenix most of us older mechs never have worn gloves, in 50 years of spanners never done me any harm, I just wash my hands before taking a piss

@dwightPhoenix 4 года назад

@@mikewatson5457 yup. As an engineer and a Safety official very on unsafe. See it all the time. Nothing is wrong until something goes wrong......

@aceyorba Год назад

He has done this many times..my bet is its a $1000 dollar job to do the brakes

@jim5870 3 года назад

He didn't clean the wheel bearings

@darrin9333 3 года назад

didn't even look at them.

@graken22 6 лет назад

I wish that chit was that ezy??

@airport4173 8 лет назад

daihatsu FOURTRAK rear brake.

@johnoldson8629 7 лет назад

yale fork lift wet brakes

@johnoldson8629 7 лет назад

Yale fork lift wet brakes replacement

@micheldupras7854 6 лет назад

Am I the only one that gets disturbed by how he just hammers the seals?

@scottedwards2349 5 лет назад

This is the way we all used to install seals....notice how easily it went in? This guy knows what he is doing!

@luismorejon7050 4 года назад

I like to put a little block of wood on top of the uninserted hub seal and hammer that block causing the seal to equally go in hub so that I don’t damage seal.

@danwilliams6769 3 года назад

@@luismorejon7050 From my limited experience all auto and some industrial seal material is comprised of a softer metal substance for the outer material. I agree that using a piece of wood works well by moving or indexing the wood around the whole 360 degrees of the exterior of the seal, however if one does this on a frequent basis a inexpensive seal driver kit will be a time saver and you will have the full contact rather than risking damage if you strike to hard. Also a compothane or brass/aluminum hammer. Would be less risky than a standard ball peen steel surface.