Hyper Tough H2520 25cc How to rewind recoil spring and pull string on a weed eater. This demonstration could also help with installing a new recoil spring.
For the last 18 months I've not let the lawn crew edge or use a weed eater in my back yard. ru-vid.comUgkx_rBCFuDW1zD6blTGhLkvAkxU657uR_lG I didn't like the fact that they just kept cutting the edge of the lawn further and further from the rock lining the flower beds and leaving bare ground. And the grass was trimmed or scalped several feet around trees, etc. It was a constant battle with them so I told them to just mow and no trimming. I have Zoysia grass so it grows pretty slow. Obviously after a while it could use some trimming. I'm in my 80's so I can't do much of it myself.Finally I decided that if I could find a lightweight battery powered trimmer I might be able to do some light trimming. I decided to buy the LST201 20V trimmer. And it works great for my needs. I have back yard with about 150' of flower beds and several trees to be trimmed. I can lightly trim the whole yard with a single charge! The grass I trimmed was only a few inches high but the trimmer was more powerful than I expected.
jeez, I'm glad I didn't trash my recoil spring, it popped out on me today and I'm like there's no way I'm getting that spring back into position, now i see it is not that difficult, this will help me out greatly
After fighting with the recoil spring for 15 minutes I found this video. Thanks man, my hands were starting to cramp up. The only thing I did differently is,That, I un did the knot on the pull handle and installed the cord on the spool so after loading the spool, the last step was just to get the string to the hole in the horsing Instead of trying to fish it through the housing and through the spool and then make the knot.
Thanks for your video bro‼️💯 Before ur video I was told these replacement parts were not meant to be opened back up and you had to just buy a whole new one when it came to replacing or repairing the cord string but after I followed your video step-by-step I ended up dropping the damn thing on the floor and it just exploded everywhere UGH 😩 😣 😑 so I’m watching your video and I’m about to try it again this time I will glue that damn thing to my hand Thanks man. Have a great one.‼️
great video, one suggestion, take the rope off the pull handle and wind it around the spool before you do the tension. Then you can just hold the string under tension with a clamp and tie the not onto the pull handle. easier than trying to feed the rope and hold the spring at tension. Thanks again for the video
there is an easier way to wind the pull cord with only two hands. Put the cord through the feral, case and pulley. Tie the knot in the pulley. Now, if you look at the pulley, you can see there is a small slot on the perimeter of the pulley. using a flat screw driver, push the cord int the slot. Now, assemble the pull into the case. loop the cord over the ratchet end. so it doesn't want to slide out of the slot. Wind the pulley for the 4 turns. On the final hold the pulley and slide the cord out of the slot. While still holding the tension on the pulley with a finger, lift the casing up to let the 4 winds of the cord relax ( because it gets twisted ). Now hold the cord and let it feed in slowly, releasing the pulley. No need to explain to the wife where she needs to hold thing.
@DennisLiverani, I have a Craftsman p2100 pole saw, and I've duplicated everything you did up to installing the clutch assy but the arrows aren't lining up like they did in your video! Any idea of what could be wrong?
For some reason my arrows are not lining up like yours was does it really matter? What got me to take this whole thing apart was that it doesn't engage the engine when I pull the start rope only about twenty to thirty percent of the time does it actually engage the engine and spend the engine over
@@dennisliverani4293 no wear at all...I'm wondering if the pulley itself just isnt spinning because of dirt...and it isnt engaging the gear...Think I'm just going to replace the whole mechanism and make sure I don't leave it outside again...
It definitely fix mine. But u need to break the metal holding seal ring to open the back whirling spring gear box. That seal is one time use and I see no where to sale that. I put everything back without the seal, it only last about 5 mins then all the gear box fall apart. Guess I would never buy this Walmart cheap shi@$t. They don't want you the fix it or replace the part.
This is why I will not buy Troy bolt, hyper tough, black max, craps man or any cheap modern Mtd type weedwacker. When something goes wrong with it, Get yourself a STIHL or an ECHO.