How to Frame Reinforcement on 1964 Impala Lowrider Hydraulics

Подписаться 19 тыс.

Просмотров 124 тыс.

50% 1

Frame Reinforcement on 1964 Impala Lowrider Hydraulics. This video is intended to help other learn how to reinforce a frame for hydraulic setups. The 64 impala was made with a X frame that can't withstand the force produced by hydraulic suspensions for very long. It is necessary to take the proper steps in reinforcing the stress points on the frame. Same goes for many other lowriders, reinforcement is almost always a must. I have personally seen the aftermath of a hydraulic setup without reinforcement, sagging doors, sagging fenders, most common is the body will start to crack behind the back window where the entire rear frame has bent downward due to weight in the trunk. Hopefully this video can start you on the right path.
#tennesseeonhydraulics #lowrider #hydraulics
FOLLOW US ON TIKTOK AT:
vm.tiktok.com/...
FOLLOW US ON FACEBOOK AT:
/ 775197889302991
FOLLOW US ON INSTAGRAM AT:
...
Have an issue you just can’t figure out? Look through the videos listed below and if you still can’t find the answer, contact me directly at:
/ lowriderhydraulicstips
How To Hop with Hydraulics Lowrider
• How To Hop with Hydrau...
HOW TO 3 WHEEL WITH HYDRAULICS TUTORIAL LOWRIDER
• HOW TO 3 WHEEL WITH HY...
How to Troubleshoot Clicking Lowrider Hydraulics
• How to Troubleshoot Cl...
HOW TO LIFT YOUR CAR WITH BAD SOLENOIDS LOWRIDER HYDRAULICS
• HOW TO LIFT YOUR CAR W...
Switchbox wiring diagram HOW TO Lowrider Hydraulics
• Switchbox wiring diagr...
How to Making Hydraulic Battery Cables Lowrider Hydraulics
• How to Making Hydrauli...
How to Cylinder O Rings Leaking Replacement Lowrider Hydraulics
• How to Cylinder O Ring...
How to Hydraulic Motor Replacement Lowrider Hydraulics
• How to Hydraulic Motor...
How to Putting together fittings on Lowrider Hyrdualics
• How to Putting togethe...
How to Frame Reinforcement on 1964 Impala Lowrider Hydraulics
• How to Frame Reinforce...
How to Taking cylinder out of car lowrider hydraulics
• How to Taking cylinder...
How to Basics of hydraulics Lowrider How it all works
• How to Basics of hydra...
How to Switches How They Work 3 6 & 12
• How to Switches How Th...
How to Bleed Lines on Hydraulics Lowrider
• How to Bleed Lines on ...
How to Hardlines tutorial impala Lowrider Hydraulics
• How to Hardlines tutor...
How to Make Hardlines for Lowrider Hydraulics
• How to Make Hardlines ...
How to Impala Hydraulics Install Part 1 Lowrider Hydraulics
• How to Impala Hydrauli...
How to Impala Hydraulics Install Part 2
• How to Impala Hydrauli...
How to Impala Hydraulics Install Part 3
• How to Impala Hydrauli...
Fat Sticks versus Standard Cylinders Lowrider Hydraulics
• Fat Sticks versus Stan...
Gas Hopping How to Lowrider Hydraulics Lowriders
• Gas Hopping How to Low...
How to Replace Dump Seal Lowrider Hydraulics
• How to Replace Dump Se...
64 Bel Air Wagon Build Lowrider Hydraulics Part 1
• 64 Bel Air Wagon Build...
How to figure out what wire goes to what for lowrider hydraulics switchbox • How to figure out what...
How to S10 4 Link with Lowrider Hydraulics
• How to S10 4 Link with...
How to Measure a Cylinder size
• How to Measure a Cylin...
How to wiring with hydraulics
• How to wiring with hyd...
How To Change 4 Switch FBSS to Multiple Function
• How To Change 4 Switch...
How To Power Ball and Polyurethane bushings and install Lowrider Hydraulics • How To Power Ball and ...
Check Valves How To Install
• Check Valves How To In...
2 Pump Standing 3 Lowrider Hydraulics
• 2 Pump Standing 3 Lowr...
Spark Blocks How To Install Lowrider Hydraulics
• Spark Blocks How To In...
Hydraulic Fluid How Much To Add Lowrider Hydraulics
• Hydraulic Fluid How Mu...
Piston Pump Tutorial Lowrider Hydraulics
• Piston Pump Tutorial L...
CLEANING A HYDRAULIC MOTOR LOWRIDER HYDRAULICS
• CLEANING A HYDRAULIC M...
How to ground a motor lowrider Hydraulics
• How to ground a motor ...
HOW TO CHANGE FLUID LOWRIDER HYDRAULICS
• HOW TO CHANGE FLUID LO...
HOW TO INSTALL ACCUMULATORS LOWRIDER HYDRAULICS
• HOW TO INSTALL ACCUMUL...
Changing out Springs Lowrider Hydraulics
• Changing out Springs L...
WHAT TO LOOK FOR BUYING A LOWRIDER HYDRAULICS
• WHAT TO LOOK FOR BUYIN...
ALL LOWRIDERS NEED TO WATCH OUT FOR THIS!! LOWRIDER HYDRAULICS • ALL LOWRIDERS NEED TO ...
LITTLE SECRET LOWRIDER HYDRAULICS HOW TO
• LITTLE SECRET LOWRIDER...
WONT GO DOWN “PRESSURE LOCK” LOWRIDER HYDRAULICS
• WONT GO DOWN “PRESSURE...
FITTINGS SIZES AND STYLES LOWRIDER HYDRAULICS HOW TOO
• FITTINGS SIZES AND STY...

Опубликовано:

21 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 119

@toddsmith1690 3 года назад

Bucket list car. I’m terminally ill and unless GOD does a miracle I won’t be around long enough to buy or build. Beautiful work. God Bless you brother.

@idontknowyouvalid5400 3 года назад

I'm so sorry god be with you Amen❤❤

@Mac_with_the_lsx 3 года назад

Tell me you still here mane

@toddsmith1690 3 года назад

@@Mac_with_the_lsx yes. Barely hanging in. Thanks 🙏🏻 and God Bless

@chevelle7873 5 лет назад

Tell that welder to go on lunch break next time you film a video!

@icebreakers8378 4 года назад

He’s a real welder ha

@mcdxvid6139 4 года назад

He don’t take breaks

@davidrobinson4057 3 года назад

He’s paid by the hour not job lmao. He be takin them breaks

@georgechadis4713 Месяц назад

No shit lol

@alonsomajikal3158 7 лет назад

What a great video. This is what youtubeing is all about, sharing that knowledge. Thanks for taking the time to put this video up guys. Very, very helpful.

@emmanuelekeleme4935 7 лет назад

this is the first time in life I have EVER commented on a you tube video! I am compelled to express what i just saw in this video. So, first of all, this is by far the greatest in depth video i have seen on frame reinforcement. Not only that, the lingo that dude is using is straight hittin switches in the streets lowriding. I love the passion and appreciate all who keep the lifestyle alive. The only thing I'm mad about is that yall aint closer to Philly to work on my 64 impala conv. 4 pumps 10 batt. fyi, been lowriding for 25 years. keep up the good videos!

@LOWRIDERHYDRAULICS 7 лет назад

Emmanuel Ekeleme that's what started all this, hard to find any information or help with this stuff, I'm also working on several others that I will be posting soon.

@jamesgilliam7539 7 лет назад

Emmanuel Ekeleme CHILL is that you commenting

@AaronChristensen 7 лет назад

Emmanuel thank you very much man. Im 37 years old and have been into the lifestyle since I was 16 years old. Definitley not something that you can just stop. I don't care how old I get, a passion is a passion no matter what.

@MrTheHillfolk 7 лет назад

Aaron Christensen I'm into another genre of cars you could say, but I love lowriders.. the time and effort put into them is amazing... I know cause one of my cars is in 100 pieces. Haha hey if ya can't get a low rider car get a bike , I did😬

@gridebrougham 6 лет назад

Just go to Motion 3 Customs.. Hmm Lol 😝

@slipsonic809 10 месяцев назад

Nice video! Im on the tail end of frame off restoring my 64 hardtop. I opted for air bags from BC Fab, you cant do as much with bags but hydros are just so heavy. I wrapped the X section of the frame on my car for a little added rigidity. Should work out alright.

@lumurumba 6 лет назад

Hard to listen with the welding noise in the background, but other than that, great vid. Thanks!

@AaronChristensen 7 лет назад

Thanks for all the comments guys. Just an update, the frame is finished and has been filled and painted. Also, the adjustable upper control arms have been removed and replaced with OEM arms. They have not been extended or reinforced yet but definitely will be. Front end has been put back and as well as the rear end. Had to replace a rear main seal in the engine yesterday and new oil pan gasket which took up a lot of time. Also got the y-bone on Saturday and have installed it. Hopefully have the engine mounted today and maybe even the body back on the frame. Also, the battery and pump racks have been primered, painted and cleared with paint that was matched to the car.

@warrentopping5764 7 лет назад

very....very cool & informative video that addresses real world problems & solutions that can arise when tackling a tough mechanical task dealing w/ framework....nicely done!

@snyper5150 2 года назад

Very, very informative. I have a64 impala convertible. I, unfortunately, cannot install Hydros on it because it would be a HUGE waste of money because of the roads in this city. But, hopefully, one day I can get the frame reinforced and toss switches on it.

@Mark-zk7mv 7 лет назад

It's true there are very few videos on wrapping a frame. Thanks for taking the time to make these. very helpful. I'm wrapping my first 66 impala frame and trying to make a few quick videos along the way. I'm looking for all the help I can get. maybe you could do one on molding the frame after reinforcenent? Thanks again man....

@raulfuerte8472 3 года назад

Thank you guys for the video!!

@alrod7ify 2 года назад

Great job & video bro

@geehernandez8446 5 лет назад

How many sheets of 3/16s did u use for the whole frame

@jasonlopez4855 3 года назад

What a bout the Cold welding spot When you weld 4 inch at a time.

@joegarcia4944 6 лет назад

Reinforcing the frame for hydraulics seems like the right thing to do. But how much does it cost to remove the frame from the body and reinforce the whole frame like in your video?

@cabernettanks6955 6 лет назад

Joe Garcia Im wondering the same thing.

@danieleckerman7099 5 лет назад

Looking at 2500 on a homie hookup to 5000 but you can find one for 3000-3500 I’d do it

@genodinero 5 лет назад

@@danieleckerman7099 i just got a 62 w mad frame cancer in the rear. good to know..

@JonathanVasquez-o7o Год назад

About $8,000-$12000

@JonathanVasquez-o7o Год назад

@@danieleckerman7099 I wish but you are off about 7to 10 grand

@slickpanther06 4 года назад

Do you have to have a full wrap on a 64 convertible because it has less support? Can you get away with a stress point reinforcement if you’re just doing fbss and no 3 wheeling or hopping.

@SugarHill28st 7 лет назад

any old car you must wrap the whole frame period

@mooremaceo 6 лет назад

S.I. Thug that’s the right way to do it fa sho

@miahriah5939 6 лет назад

What about if its partial reinforcement?

@Lowridersdoggs 7 месяцев назад

What do you charge to do a full frame wrap?

@gibfortune 3 года назад

Will you reinforce the frame of a four-door Mercedes Benz for me so that I can cut the roof off

@LPXNelly 7 лет назад

How about a 90s Cadillac Brougham on two pumps 6 battery setup ?

@antoniomendez9119 6 лет назад

Raser Cat do the 4 stress points and the chest plate should be good enough bro

@moptop85 6 лет назад

Look up 1959 olds guard beam frame, if you added those side beams I bet it would help out

@BryanAnderson-ti5ew 3 года назад

Where are you located at. I just got my first lowrider ever. Lincoln Town Car & i want to do it right???

@LOWRIDERHYDRAULICS 3 года назад

Clarksville TN

@potpans980 6 лет назад

Hello, I am currently doing a 63 impala hardtop to functional factory working vert conversion, and I was wondering if you know what the interior body structure for the vert looks like, I have the vert frame and windshield frame I just need to know and see what all else the interior structural integrity needs to have done to it! Thanks

@joeolivas7437 8 месяцев назад

Do you box in the back in support

@sadame1414 6 лет назад

Good work Russ !

@alrod7ify 2 года назад

How much is it to re enforce the frame? More or less

@asulliv1954 6 лет назад

I was wondering on some low riders I notice chains in the rear axle to the trunk I think and can you get the same affect using air bag shocks I think they are?

@rogersonnier7892 5 лет назад

I like your videos! Can u make a dog leg video (rear three wheel) thanks .....

@LOWRIDERHYDRAULICS 7 лет назад

They were on it when he got it, we have to change them out, they touch the frame now with no weight on the frame.

@TREALLDAY-nj1dz 7 лет назад

More videos please.

@LOWRIDERHYDRAULICS 7 лет назад

R D Rob working on it. Have several coming up. How to make removable battery racks, custom rear spring perch and reinforcement, installing extended trailing arms and how to make them work. Anything specific your wanting to know?

@TREALLDAY-nj1dz 7 лет назад

No nothing specific that I need. I just really enjoyed watching your video. I was always curious how they reinforce frames to three wheel. Now I see how it's done

@davidalvarado733 4 года назад

Can i reinforce without removing the body.

@sergioramos4967 7 лет назад

Where is ur shop good stuff man good information

@guadalahustler 7 лет назад

good videos .can you make some video on how to install cylinders. there no videos on RU-vid. Good job .

@LOWRIDERHYDRAULICS 7 лет назад

guadalahustler that is the video I'm working on now. Should have it up and others this week

@rustybrowneye 7 лет назад

those nubs u got welded to the rear of the frame for the rack. im sure most people weld the rack to them but have u ever seen anyone use them to bolt the rack in?

@LOWRIDERHYDRAULICS 7 лет назад

Actually those are removable racks, I just havent posted the videos yet. I will be posting the video in a couple weeks when the car is completely done. It will be a how to make removable racks and several other things.

@rustybrowneye 7 лет назад

Russell Harris cool, please touch on those in the video,,,,, it makes scents that its removable rack.

@LOWRIDERHYDRAULICS 7 лет назад

fuzzy wuzzy we did a few now like that but haven't posted the videos, it's easy but time consuming to make it all line up right. We have some pretty cool stuff coming up, stay tuned

@jackmoore2682 4 года назад

What size metal do u recommend to wrap frame

@miahriah5939 6 лет назад

how can i tell when the frame has been twisted on a 64 hardtop impala? is one door dosent completely shut flush?

@MC-gb8hn 7 лет назад

Great Vid.. Informative..

@gridebrougham 6 лет назад

I only got the rear arches, front sides, and underneath the belly. Got 3 pumps 10 batts. Starting to notice gaps in doors and fenders. Somebody said sit the car on jack stands all 4 corners and it will restore the frame and close the gaps. Then box in the center of the frame. Will that help?

@LOWRIDERHYDRAULICS 6 лет назад

Gride Brougham I’m not saying that won’t work but once the damage is done, it’s hard to correct. I doubt doing that will fully straighten the frame. But give it a try, once it has straightened as much as you can get it, fully reinforce frame and fix whatever bodywork needed.

@gridebrougham 6 лет назад

Thank you. Kinda figured it wouldn't go back 100% to specs. But If I can get it close, I'll box in the center span. My next build will be a frame off :thumbsup:

@juangonzalez-rr7wc 6 лет назад

Can I use metal plate or do I have to buy steel plate

@recordingwithrev3496 6 лет назад

What’s going on? My name is also Russell Harris. And I have a 62 impala that I want to do this to.

@juangonzalez-rr7wc 6 лет назад

Good video by the way

@leehernandez1557 7 лет назад

Will you ever do a video showing a complete build?

@LOWRIDERHYDRAULICS 7 лет назад

Lee Hernandez working on it now but unfortunately it's a process that takes time. Will post progress as we go along

@HOGSIDESJTV14BOSSHOGRECORDS 7 лет назад

those are cool a arms on top .

@AdamMargie4ever 7 лет назад

Great job on the video.

@danieleckerman7099 5 лет назад

Hey is it mandatory to re enforce the frame to start hoppin ?

@dracula293 5 лет назад

yes

@nathanaelpedroza 5 лет назад

Do I need to reinforce both sides top and bottom or leave the bottom out ?

@LOWRIDERHYDRAULICS 5 лет назад

Nathanael Pedroza it’s best to reinforce all sides if possible.

@WouldYouLookAtThis 3 года назад

Do you have contact information? I need my Frame wrapped on my 64

@djenglewood 7 лет назад

i have never seen adjustable upper control arms b 4

@gayrunnycumstain 4 года назад

stfu bitch nigga

@chrisvelarde2106 5 лет назад

How much will this cost to do on a 68 Cadillac deville

@HOGSIDESJTV14BOSSHOGRECORDS 7 лет назад

jus subbed.good work

@Wewhoooooo Год назад

Naw you said it right the first time!!!!!!! LINCOLN

@LOWRIDERHYDRAULICS 7 лет назад

Playing all 4 sides, boxing in everything

@chrisjones3789 4 года назад

I have a 64 and a extra 64 frame im not using, can i cut up one and weld it to the other

@daddyboss907 7 лет назад

So are u just pretty much putting plate steel where ever the frame isnt already boxed..or are u completely wrapping all 4 sides of the frame in plate steel

@lonestarlows 6 лет назад

Easier to sell convertible frame get a ht frame add 2 body mounts and u don't have all the factory welded reinforcements in the way

@marlineharrold1937 6 лет назад

awesome. :D

@rcjr1371 6 лет назад

Is 1,700 too much for a partial wrap for my 63 Impala? That's what they wanna charge me when they install my hydraulics?

@LOWRIDERHYDRAULICS 6 лет назад

RC Jr depends on where exactly the are reinforcing, thickness of metal, and quality of work. But assuming they are using 1/4 inch since it’s just a partial wrap, and the welds are nice and the work is good, $1700 is a decent price. My suggestion before you do that would be to call Pit Bull Hydraulics and ask how much for a completed frame, they have them already done sometimes, just send them your donor frame and they send you a finished one. Not always but they are the gold standard when it comes to frames. Brent knows his stuff

@rcjr1371 6 лет назад

They're mainly focusing on the front and rear axle, they're not removing the shell of the car. Thanks! I do plan on doing a little hopping and maybe three wheel.

@LOWRIDERHYDRAULICS 6 лет назад

RC Jr my advice is to find someone else that knows impala frames and Hydraulics to do the reinforcing. The weak points of the x frame at mainly from the middle to the back. Call Pit Bull

@rcjr1371 6 лет назад

Russell Harris Lowrider Hydraulics thank you

@miahriah5939 6 лет назад

I looking into buying a 64 hardtop impala that is partial reinforced trail arms,a arms,side & bottom of frame. is those areas the main stress point for a 4 pump car? Thanks

@52YOUNGHOGGHGC 5 лет назад

Are you guys located in Clarksville

@LOWRIDERHYDRAULICS 5 лет назад

Yes

@52YOUNGHOGGHGC 5 лет назад

Russell Harris Lowrider Hydraulics would've never knew. I have a 63 4 door belair i want to transform into a lowrider but couldn't find anyone in the city to do it. The shops i went to kept talking about airbags and I'm not a fan of that

@LOWRIDERHYDRAULICS 5 лет назад

Where are you located?

@52YOUNGHOGGHGC 5 лет назад

Russell Harris Lowrider Hydraulics new providence area

@LOWRIDERHYDRAULICS 5 лет назад

Find me on FB and I’ll come with a few guys to take a look, worse case you’ll have some new homies that can help you get up and going. If you are not a part of Tennessee on Hydraulics page, go join and Message me.

@Tkssa580 4 года назад

Couldn’t bare the welding in the background.

@tboneo2005 4 года назад

My car frame is made for hydros so I'm am very lucky

@marcosantacruz6035 7 лет назад

how much is this project?

@LOWRIDERHYDRAULICS 7 лет назад

Marco Santa Cruz to do yourself, if you have all the tools and equipment, around $500 worth of metal and misc items. Having someone do it, $2500-$4000. Painting included.