HOW TO - Honda Fourtrax trx 250 Carburetor Clean Carb Rebuild Kit Gas Fuel Cleaner GUMOUT Repair Kit

Подписаться 38 тыс.

Просмотров 29 тыс.

50% 1

We are disassembling, cleaning, rebuilding, and re-assembling a 1985-1987 Honda Fourtrax 250 Carburetor
Fuel Tank: amzn.to/3nLCHJt
Oil Kit: amzn.to/38ZRJY6
Starter: amzn.to/336LXjM
GN4 Oil: amzn.to/3pPHjA6
Patreon / midnebraskamotorsports
Instagram / midnebraskamotorsports
Check out my eBay store at stores.ebay.com/midnebraskamotorsports
We Disassemble: Clutch Head Cover Cylinder Piston Stator Points Rotor Magneto Generator Alternator Coil Camshaft Cam Chain Tensioner Rocker Electrical Cases Bottom End Case Set Transmission Shift Drum Fork Gear Shaft Flywheel Starter Idler Clutches Bearings U Joint Yoke Driveshaft Shaft Float Slide Needle Seat Adjust Clean Assembly

Опубликовано:

2 окт 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@ceclay1 3 года назад

I’m getting ready to do this exact carb. I appreciate the video!

@davidfloyd6084 Год назад

Just a tip. What would work great cleaning out the needles and jets is a welding tip cleaner. Really small picks used for unclogging rose buds and torch tips. Would work great here if you have access to that

@privateperson1148 5 лет назад

Nicely done video.

@loganthomas6868 5 лет назад

Very helpful thanks 👍

@fan1701 5 лет назад

So many people need these kind of videos. I'll be recommending your channel to people and also watching myself. Thanks for your efforts! I've got a bayou 220 with a low end noise I'm going to pull down over the winter and fix. Never been into a bayou before so I'll be looking to see if you have videos for them. Great work!

@rvrandy1710 4 года назад

awesome !! Thanks :-)

@tashathayer6427 2 года назад

I just bought a new one there not allot & it started right up,I probably will take the old one apart & clean it but there so inexpensive,it did take almost a week but that's fine,it won't move but working on that issue... ✌

@brianbridgeo147 2 года назад

thanks am doing one now - this helps

@MidNebraskaMotorsports 2 года назад

Happy to help. Let us know if you need anything! www.ebay.com/usr/midnebraskamotorsports

@topherg396 2 года назад

Thanks a million!

@MidNebraskaMotorsports 2 года назад

Thanks for watching Topher. Hit the subscribe button as we have a lot more videos coming out on this machine. If you need parts or tools for the job check us out at www.midnebraskamotorsports.com/

@wicziwajcha8 3 года назад

Thank you!

@wicziwajcha8 3 года назад

on my Honda there was no starter handle and lights, I bought it but I don't know what to connect to and I need a diagram or photos, please mail: wiczi1988@gmail.com

@sunnyray7819 5 лет назад

Just found your channel a few days ago, Great content, Just got me a Big Bear 350, top end torn apart.......Just a suggestion, it would be nice to set up playlists for different motor tear down rebuilds ect.

@sunnyray7819 5 лет назад

@@MidNebraskaMotorsports I am subscribed,and I always hit like, unless I forget to... Love the videos!

@sunnyray7819 5 лет назад

@@MidNebraskaMotorsports Wow you have allot of parts..

@sunnyray7819 5 лет назад

@@MidNebraskaMotorsports What state are you in?

@TheShooter466 Год назад

If the engine ran on choked but then stalled and won't start again, where would I begin? I know nothing about carbs

@steves659 5 месяцев назад

For the choke does that cable hook onto anything or just bumps up against the 'plunger'? when we too apart it was not connected so not sure how it is supposed to be. Thank you

@LanceSheppard 5 лет назад

What is your personal pre clean procedure before you even remove the carbs

@lmt-adventures620 Год назад

Good job! Followed your steps on my 85 Fourtrax 250 but still fackfiring and won’t idle, start east on full choke and Boggs to death after five seconds or so, and gets better if I spray startng fluid in carb when Bogging begins. I’m suspecting a fuel shortage just don’t know where to begin. I started at 1 3/4 turns out on carb. Cleaned carb and everything looks clean.

@vanillagorilla6845 Год назад

Try checking to see if the petcock is clogged

@lmt-adventures620 Год назад

@@vanillagorilla6845 Thanks for the input. I just solved the problem. It was a lean backfiring problem. Solved it by fixing the carb installation. There was a piece of plastic in there that seats on the main jet area-well it was installed incorrectly not sitting properly hence blocking pilot jet orifice. Twisted it to fit properly and boom! Runs like a champ now!

@vanillagorilla6845 Год назад

@@lmt-adventures620 right on. I just picked up a neglected 85 trx250 I’m working on. Gas so old was yellow and could probably peel paint off the walls. Petcock was clogged, carb was dirtiest I’ve ever seen lol. Put it back together and starts first kick but idle is way too high so I’m trying to figure that out now

@lmt-adventures620 Год назад

@@vanillagorilla6845 We for the same quad then! New to the sport but learning a lot and having tons of fun through the process. Carb Chem did the work for my carb. “Rust Dissolver” by Rust-Oleum did the magic for my rusty tank now looks brand new inside after a few days of flipping (way too long as product needs about 30 min to an hour to do the job but I had only a gallon so wasn’t touching every wall surface)….Sounds like you got her back to life, high idle doesn’t sound serious adjust the idle knob and let me know how it goes.

@Vazerin Год назад

Is the carburetor the same as the 250X?

@MidNebraskaMotorsports Год назад

Unfortunately no. Check out our eBay store for the carburetor you need. Thanks for checking. www.ebay.com/str/midnebraskamotorsports

@thssportingcenter1 5 лет назад

Kudos

@12mp121 2 года назад

I got a little rubber piece at the bottom of my carburetor I took it out but I don't remember where it goes

@lt4911 Год назад

Have you figured out?

@greggory448 6 месяцев назад

When I took this carburetor off I was thinking. What the f*** was Honda? Rethinking the carburetor thinking about toss and the thing and just putting a real flat slide on it.

@MidNebraskaMotorsports 6 месяцев назад

Well, this is a new idea on a fourtrax. Love the idea tho. Let me know how it works! Snag this kit that is on sale: amzn.to/47N6J7e

@loganwork7024 3 года назад

Hard to come by? They're all over ebay for anywhere from 30 to 60 dollars. I just got a new one in today. Good video though thanks

@sunnyray7819 5 лет назад

First

@daniellanglois851 Месяц назад

I loke your video and it seems you know what your doing but why do you have to go so fast just slow down a bit and give us new guys a second to digest. thanks

@MidNebraskaMotorsports 29 дней назад

Sorry for the speed. Viewer like me to get to the point. My goal is that people will find this videos helpful and will keep coming back. Thanks Daniel If you need more helpful tips, check out: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-X0AdFxkJiOg.html and if you need parts: www.ebay.com/str/midnebraskamotorsports. thanks for watching and the comment.

@topherg396 2 года назад

Rebuilt mine but now it is fluid in really bad.. Any idea?

@topherg396 2 года назад

Flooding really bad

@MidNebraskaMotorsports 2 года назад

Did you mess with float height? Also, I see a lot of times, guys rebuild their carbs, then during install, they put the fuel hose back on and a chunk of rubber gets chipped off of the fuel line and holds the float open. Might be worth checking. Also if you possibly didnt get the main tight enough, I've seen those work loose and give some major fits. Let me know! Thanks for the question! Hit the subscribe button as we have a lot more videos coming out on this machine. Also, check us out at www.midnebraskamotorsports.com/

@topherg396 2 года назад

i cant get it to hit at all i even put a brand new carb back on it. wont say nothing. good spark also. changed the coil