how to instal a 3 inch lift / levelling kit on a 2007-2013 GMC sierra Chevy silverado 

you can buy the lift kit on Amazon here: amzn.to/2Es0eK4

Did this on a 07 Yukon denali a few years back. The front was a total pain! Got the 3.5" leveling so a spacer above and below. Installing the 2 lower bolts got me creating new 4 letter words for the time it took to get them in. Definitely needed and alignment afterwards too, but also get a correct angle upper control arm for anything over 2 inches. The ride is a bit more stiff, but works great for me because it reduces roll on turns. Rockin 35s MTs under my Yukon Denali and been loving it for a few years now.

Good video I just got done with mine it took 9 hours but it looks great

You absolutely do not have to take the upper control arm out of the spindle to take the strut out all you need to do is remove the sway bar link unbolt it from the lower control arm Loosen Three Top bolts and a push it towards the front diff and it pops right out

Badass! Going to do this to my Tahoe since they’re all pretty similar

hey i just wanted to say thanks just finished installing it on my 07 silverado using your instructions and they were very clear. it now it has an aggressive look

Easy job to do. its those rough country, bds, rancho, superlift 4-6-8in lifts thats a killer.... damn frame cutting, triming and drilling....... happy all i need to do it a torsion bar key done with a c clamp...

Good video. Enjoyed the music. Nice editing.

Excellent how to. Everyone removes just about everything to get these in and you don’t need to at all. I finished my 3.5 (3.5 inch lifted struts from rough country) in the front relatively easy. Thank you! I didn’t remove the tie rod nuts because they were spinning. Decided to move forward and was able to get the new struts in no problem with a little elbow grease. Anyone doing this, I would definitely recommend new upper control arms. It makes a huge difference in the travel for that knuckle and ride comfort.

Not to say anybodys wrong but ive done 3" level kits like this on three trucks about to do it to my new 2016 chevy and most those trucks i put over 100k no ball joint issues no axle angle issues if your going with a 2.5" it's absolutely no diff .5" isnt gonning to make or break you. If you want a 3" lift and clear larger tires do it you wont regret it if your just looking to level the truck use a 2" kit and have piece of mind. The motofab i bought was on amazon 124.99$ free shipping easy install as you watched. Besides if the ball joints did go out big deal replace the upper arm and joint at that point thats my plan on this new chevy and if the angke is bad enough theres a easy install for a front diff drop to help if needed really cheap as well. Good luck! Enjoy

Great install video! Thank you

Great video but I have a question what are the torque specs for the spacer nuts

Hello thanks for the video did learn a lot but my daughter bought a 2009 Chevy suburban with a lift kit but hers' looks like a u-joint and my grandson changed I can't remember but her tire, passenger side, fell off he called himself putting it back together trying to hammer something to make it straight instead of just replacing it make a longer story shorter the wheel bearing went bad had to replace that and an axle but that u-joint can't get it to fit unless I drop the tire rod but does it go right under the spring and strutt on the bottom?

Thank You this video really helped a lot!

I have a silverado with a similar lift I like it a lot. BTW if you don't get the alignment right it will ruin the tires fast I recommend doing a Lazer alignment

really helpful!! thanks got my gmc lifted right by watching this video

Thanks . Helps to see it done before doing it. TZ

I Didn't have to take off the tires when I did the rear blocks on my 1999 chevy silverado 1500.

Good video. After the install, does it still have a little bit of a rake? Or is it really even?

Excellent video I’m going to do mine

I am in the prosses of lifting my gmc and was wondering why you remove the other blocks that are there already and how come you didnt have to do anything with the shock absorbers cus I out the blocks in with the old block and when i let the jack down it didnt raise it at all

Have you had any problems with the front suspension after installing this? Ball joins and such?

Hey what did your torque everything back to? I am doing mine soon and want to know the torque specs

Exelente video!!! Yo levante mi chevy 2011 si ningun problema

Question. If u already have a 3” level kit in the front can you still install a 3” lift on the front and back?

La medida del espaciador es de 3 inches o lo que levanta la camioneta son las 3 inches?

you sir need to spray under your truck before that rust damages more than it has good video by the way

How often do you go through upper ball joints?

Those headlights are dope

I have a 99 GMC yukon n want a 3in lift. what dose it take to achieve this , with out moving or cutting on transfer case. coast for kit?

Nice video man. Thanks a lot

So my spacer doesn’t have screw holes to just throw on top of the strut, it seems like I need to take my spring out, is that the case?

Do you need an alignment after you put them?

what brand was the kit and how much was it? it seams to work well

I bought 3" front and 2" rear lift kit from Ebay for $87. My 2" rear lift is different than yours, it's a full aluminium billet (CNC machined). I'm done with rear easy peasy but struggling with front. Realizing that you removed upper arm. No wonder why I couldn't get bottom of shock bracket to hang on top of lower strut. Instruction don't tell me at all. Glad that I checked your video. Hey! Did you forget to bolt in 3" billet to top shock before you insert under truck shock support?? I saw you drop in 3" billet then install under strut support body. Or you already did bolted in billet to shock "video offline"?? Wonder..

Did u have to adjust your plow after

When putting the front blocks on do u put the factory big bolts on top of the strut or in the holes ?

Nice video. Congratulations. What company did you buy the 3 inch spacer? Can you advice to me?

How did you tight the front shocks screws on top??????? It looks that there is no room to work???

What do you do about your travel

Can I just do the same on a 1991 4×4 Mazda king cab? It is easy the procedure in rear wheels but Im a little cautious to mess with the front wheels , Any help is wellcome.

Did you just use 2 jack stands and 1 jack?

Thanks man really helpful

How's was your ride after? Stiff or close to same?

Necesito ver cómo se levanta una GMC TERRAIN 2013

do you have some kind of problem with the front bearings? as buzzing noise? even alignment

Can this work for Chevrolet equinox?

did you have any trouble getting an alignment ?

what is your upper ball joint angle is it ok or out of wack?

how thick is that front spacer

Are ur headlights retrofitted

Great tutorial ! i am looking for same systme but for my Peugeot J 5 but impossible to find it in France...any adresse by any chance?^^ kind regards from Provence

Where did you get your headlights

Hello friend. I have a question. After uploading your GMC did you have an alignment?

Let’s say you add a 3 inch lift to a Tahoe does that require you to have to change shocks or can you keep using the same ones as before?!?

I did this now I have bed bounce how do I fix this

Is that a 2inch for the rear and 3inch for the front ? Year truck ?

Did you get it align ??

Great video!

We're do u buy the parts

what is a l8ft kit and what is a leveling kit ?

How bad were your upper ball joint angles?

Hi ,if u can tell me where u got the kit from

Hey are you in Canada? And is only the same process to install a higher lift?

My 08 Silverado only has 2 blocks in the front and my upper control arms sit right on the droop stops.

Great Video. Thanks.

if you do this lift... my question is.... can you do a shackle in the rear too for added lift ?.... can you do a spindle in the front as well to add lift ?.... can you also add a torsion key lift?.... an upgrade shocks too....or does this contradict each other and or cause other issues?... I wanna do my own cheap lift big enough for 35s. an I'm willing to trim an cut some...

I can’t get my the lower strut to line up with the bolt holes

Need help quick have to turn in rental today

Thanks you just saved me like 1000$ bucks

Did you get any vibrations after installing the 2” tapered rear blocks?

great video thanks

how does this effect the towing? The spacer flexes the leaf spring and thats what helps the towing weight

Would have been helpful to show spacer being mounted to strut.

Is it just me or are those frowny face leaf springs shot

De qué parte de EEUU mandan su producto supreme suspensión para una pick up Nisan Frontier 2005 2wD hacia Mexico en el estado de Coahuila

What kit is this????

curious to know how the truck is holding up as well. could u fill us in on if there were any issues with the ride or joint problems

why does my truck lift up when trying to put the top bolt on?????

I'd like to do this to my 95 Chevy Silverado.. can u give me some tips

I just got a 3"to1 level kit and the 2 spacers are 2"equal is that normal or they send me the wrong part get back to me when you can

Nice video

I would get it aligned after

what brand did you go with? for the level kit and the blocks for the leaf spring?

Where can I find that kit?

What kit/brand is this? Looks really good bro

Did you bolt the spacer to the strut or its just sits on it and just holding with the pressure?

Tire size?

I really wanna put a 3" lift on my Chevy blazer

Question:after you put the leveling kits you take the truck to alignment or not?

3 inch lift dont go to well with the tires i saw in this vid what are best size tires that look good on a 3 inch lift

Did you ever needed to add any new parts on the truck? Like knuckles, a arms or tie rods?

I put this lift/leveling kit on my 2013 gmc Sierra. But now my front end is higher than the rare. Please hel me out. And explain this this to me.

Think I woulda pressure washed it first

You should show the video when your using the jack to put the bolts

do u recommend to take the truck to get it reallined?

Broo THANK YOU

Won't it ruin your bearings because it's uneavean

What I need to do for lift a Isuzu Rodeo 1995

I have a 2011 Silverado LS 2WD would a 3in lift kit be a good idea