No video :(

How to Install a 12V Socket in Your Car - Subaru Impreza 2018

Подписаться 706

Просмотров 12 тыс.

50% 1

In this video, I'm going to show you how to install a 12 volt socket in your car as well as disassemble some of the interior. I'm installing this in the back of my car, but you can install it anywhere you want power.
Im installing this in my 2018 Subaru Impreza, so this guide will be very helpful if you are planning to install on a Subaru as well.
If you are not, the same principles for electronics apply: running the wire, attaching the fuse tap, attaching wires and so on.
Did you try this install on your car? Let me know in the comments and if you have any questions about this build.
#12voltsocket #subaru #impreza
Tools and other stuff:
Plastic prying tools: amzn.to/3eOf7K9
Fuse tap: amzn.to/3zvV3nV
14 gauge wire: amzn.to/3f5ycYD
Terminal crimpers: amzn.to/3iUhTir
12V socket: amzn.to/2V6sSwE
Dremel tool: amzn.to/3zwPhm1
Production gear:
Gopro hero 8 black: amzn.to/3BzTiHV
Lav mic pack: amzn.to/3zquyjt

Опубликовано:

1 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 17

@jeffrey3498 Год назад

That’s a massive amount of work.

@heatherm8261 9 месяцев назад

Interesting that you took the seat out. I ran trailer wires to to a 7 way tv plug I installed and never once thought the seat was in the way. I am looking to add a 12v plug for a dash cam in the rear of my car so the video was a nice refresher on where all the. Lips and screws are.

@fgardner 2 года назад

Very high production quality! Good job man

@goinhigher 2 года назад

Thank you!

@skylarfairchild3234 2 года назад

Perfect, needed this for my install on my 18 wrx

@goinhigher 2 года назад

glad it helped.

@semoemo1 10 месяцев назад

Should note on using fuse taps the prong with the wire side coming out should be on the negative side in the fuse box. Otherwise power flows bypassing the fuse making it point less.

@drivemixgame 3 года назад

This is impressive video work.

@goinhigher 3 года назад

Thank you!

@FriaGram 2 года назад

I have the hybrid, it has a little pocket on the right side where the air compressor kit fits. Looks like I can just drill out the bottom of it and the socket will drop in, and the socket will be facing upward. I didn't take apart all of the panels on the right side, but I assume it's the same as the left. Any reason not to run the wire along the passenger side, and then behind the glove box to the fuse panel?

@FriaGram 2 года назад

Also I should mention the hybrid is a bit odd. The battery is a good 4 inches higher than the lift gate platform. Also, there is an air vent on the left and right (i assume for battery venting), as well as an air vent on the right panel beside the rightmost passenger rear seat. Doesn't look like the older crosstreks have this.

@goinhigher 2 года назад

The only reason I went around the drivers side was because I figured it would be easier to run the wire along the body and then have quick access to the fuse box versus behind the dash.

@FriaGram 2 года назад

@@goinhigher I was able to drill a hole in the bottom of the right panel. The hybrid has a little 6 inch by 6 inch cubby in that side for the air pump, so there is enough room. And yes, I ran it under the dash and glove box, and down the right side.