How to Install a Pool Table Cloth - FULL DIY GUIDE, BEST ON YOUTUBE!!!

Подписаться 10 тыс.

Просмотров 388 тыс.

50% 1

Packed with useful Tips & Tricks, this video will take you through the full process of installing your new Pool Table Cloth, saving you HUNDREDS of dollars in install fees by allowing you to fit your own cloth!
AMAZON LINKS:
Worsted Cloth:
USA: amzn.to/3e2eX1q
Canada: amzn.to/3jl53L2
UK: amzn.to/3Iq2HYw
Napped Cloth:
USA: amzn.to/3NGG5Vt
Canada: amzn.to/3VMymX9
UK: amzn.to/3CqFRfG
Air Stapler:
Amazon USA: amzn.to/47o9VFX
Amazon Canada: amzn.to/46r3SiP
Amazon UK: amzn.to/3RcNdeg
T50 Staples:
Amazon USA: amzn.to/40MVbyd
Amazon Canada: amzn.to/49PFiew
Amazon UK: amzn.to/47Kmb3r
Staple Remover:
Amazon USA: amzn.to/3SYKmY1
Amazon Canada: amzn.to/3QS0RCl
Amazon UK: amzn.to/46s3EI0
3M Super 77 Spray Glue:
Amazon USA: amzn.to/3R7YGe0
Amazon Canada: amzn.to/3R7YR9a
Amazon UK: amzn.to/41cSjdZ
Alternative Spray Glue (Fabric Compatible):
Amazon USA: amzn.to/3GtIDlP
Amazon Canada: amzn.to/3NdGmiv
Amazon UK: amzn.to/47I4EcI
CHAPTERS:
0:00 Intro
0:58 Stapling vs Gluing methods
1:39 Equipment required
2:23 Preparation
3:45 Laying out the new cloth
6:38 Starting at the head end
8:41 Moving to the foot end
11:46 Side Pockets
16:27 Drawing cloth into the corners
18:24 Working on the sides
21:20 Corner pockets
23:46 Trimming off spare cloth
24:42 Holes for rail bolts
29:35 Final thoughts
OUR OTHER POOL TABLE CONSTRUCTION VIDEO'S:
Pool Table Complete Installation:
Basic Install, Older Table: • How to Install and Clo...
Advanced Install, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Level Your Pool Table Frame:
Basic Method, Carpenter Levels Only: • Pool Table Assembly: H...
Advanced Method, Machinist Level, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Level Your Pool Table Slates:
Basic Method, Carpenter Levels Only: • Pool Table Assembly: H...
Advanced Method, Machinist Level, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Seal Your Pool Table Slate Seams:
Beeswax Method: • How to Seal Pool Table...
Bondo Method: • How to Seal Pool Table...
Sealing Pool Table Slates: Beeswax vs Bondo - Which is Best?:
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Make Pool Table Slate Pocket Liners:
Advanced Method, Neoprene or rubber etc: • How to Make and Fit Po...
Basic Method, Cloth Strip: • Pool Table Cloth Insta...
How to Replace Your Pool Table Cushions:
• How to Change Pool Tab...
How to Fit Your Pool Table Cloth:
Advanced Method for Worsted Cloths inc Simonis/Predator/Championship etc: • Pool Table Cloth Repla...
Basic Method: • How to Install a Pool ...
How to Calculate the Stretch Index of Your Pool Table Cloth:
• How to Calculate the S...
How to Finish Your Pool Table Pockets the Right Way:
Advanced Method Custom Liner: • Fitting Pool Table Clo...
Basic Staple-Only Method: • Pool Table Cloth Insta...
How to Re-Cloth Your Pool Table Rails:
Basic Method: • How to Re-Cloth Your P...
Advanced Method, Simonis Cloth, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Install Pool Table Rubber Pockets:
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Calculate Your Pool Table Difficulty Factor (TDF):
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Mark Your Pool Table (for Pool):
Basic Method: • How to Mark Your Pool ...
Advanced Method, Simonis Cloth, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Mark Your Pool Table for Snooker:
• How to Mark Your Pool ...
How to mark Your Pool Table for Snooker (Technical Considerations):
• Marking Your Pool Tabl...
How to Drill a Pool Table Slate:
• How to Drill Pool Tabl...
PLEASE NOTE: This video was originally produced for our General DIY channel (Fix Savers) before we launched our dedicated Pool channel (Average Joes Pool), hence the Fix Savers branding in the video.
VIDEO BY: Average Joes Pool/Fix Savers (all rights reserved)

Хобби

Опубликовано:

11 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 215

@AverageJoesPool 2 года назад

Worsted Cloth: USA: amzn.to/3e2eX1q Canada: amzn.to/3jl53L2 UK: amzn.to/3Iq2HYw Napped Cloth: USA: amzn.to/3NGG5Vt Canada: amzn.to/3VMymX9 UK: amzn.to/3CqFRfG Air Stapler: Amazon USA: amzn.to/47o9VFX Amazon Canada: amzn.to/46r3SiP Amazon UK: amzn.to/3RcNdeg T50 Staples: Amazon USA: amzn.to/40MVbyd Amazon Canada: amzn.to/49PFiew Amazon UK: amzn.to/47Kmb3r Staple Remover Amazon USA: amzn.to/3SYKmY1 Amazon Canada: amzn.to/3QS0RCl Amazon UK: amzn.to/46s3EI0 3M Super 77 Spray Glue: Amazon USA: amzn.to/3R7YGe0 Amazon Canada: amzn.to/3R7YR9a Amazon UK: amzn.to/41cSjdZ Fabric Spray Glue: Amazon USA: amzn.to/3GtIDlP Amazon Canada: amzn.to/3NdGmiv Amazon UK: amzn.to/47I4EcI

@mysty0 2 года назад

Hey buddy, I looked at your links and you only sell cloth in 7/8/9 sets.. any chance of a napped 12' x 6' set?

@dannyortiz1598 4 месяца назад

NH V V BVLGARI. PPPPP B B"CHYNA U

@CraftyHalo Год назад

i don’t have a pool table but i felt like this was necessary to know how to do for some reason

@AverageJoesPool Год назад

Glad you enjoyed the video 🙂

@ginadoughty6950 Год назад

Hahaha!! Me too!!

@ImPredial Год назад

This is easily the best tutorial on RU-vid for felting a pool table. Clear and concise information, while showing perfect camera angles as he’s explaining. Followed this video step by step and my table came out immaculate. Thank you so much! Called up a few local places to who felt tables and you saved me $650 USD, and a 2 month wait. Thanks again.

@AverageJoesPool Год назад

That's awesome! Really glad that we were able to help guide you through the installation, and of course save you all that money and the waiting time too. That's awesome! Thank you for your support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@user-pw5nb7lo2s 18 дней назад

My wife and I did it. We were somewhat slow, starting and stopping the video moving very slowly watching it several times. It turned out great. I used the worshed 20 oz cloth. played my first game on it today. I think the rails were the hardest and I think mine looked better then the videos. OK maybe. Thanks for your instructional video, no way could I have done this on my own. you are awesome sharing your knowledge.

@AverageJoesPool 15 дней назад

Really glad that we were able to help you out, and that you installation went smoothly! Great stuff, and thank you for your support! 👍 ----------------------------------------------- To help support us: 1) Please be sure to use our Amazon Links! 2) Please ensure you LIKE our video's, and SUBSCRIBE to our channel! 3) Donations always welcome! Hit the SUPER THANKS option below the video on RU-vid! Thank you for your support!

@DaveRondinone 5 месяцев назад

I refelted my table for the first time today and your videos were my guide. Thank you!

@AverageJoesPool 5 месяцев назад

That's great! Glad to hear we were able to help you out with your installation, and enjoy your game! 👍 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@fredericktrummer8941 Год назад

Thank you very much for the time and effort in making this and the other video tutorials. Just finished the process of my first assembly up to beginning to install felt now. Without your videos, would never have been able to get to this point at the quality desired. Have been learning lots of added tips and tricks on final leveling after 0 degrees on the digital level by slow rolling a ball on the slates, and techniques of getting super flat beeswax on cracks and filling holes (level) with beeswax. Your videos gave me the confidence to attack the project with my Olehausen. The pocket finishing is something prior installers never did and it will look far better than the pros who left ugly cuts visible in the pockets of my last table.

@AverageJoesPool Год назад

That's great to hear! Really good to know that we've helped you out along the way with you install, and hope everything went nice and smoothly for you! Yes, the pocket finishing is something that is overlooked a lot (even by professional installers, as you mentioned, most likely due to time factors) but it does make such a big difference to the overall look inside the pockets - those cuts always look terrible (ironically, somehwhat unfinished in appearance, lol!) Thanks again :-)

@garygabbard5995 2 года назад

I've been scratch building a pool table and had very little luck finding tutorials that would help. I've found these just in time to help with levelling and covering. Thanks so much. Great vids.

@AverageJoesPool 2 года назад

Excellent! Glad we could help out!

@lilformersmatt 2 года назад

Just used this as my main guide to replacing the cloth on our table. It was left with the house we bought this year. and in rough shape. Very helpful, thanks!

@AverageJoesPool 2 года назад

Glad it was helpful!

@baddad18 9 месяцев назад

Agree with all the previous positive comments as your tutorials are the most comprehensive yet concise I've yet seen on RU-vid. You Sir are "Far Above Amateur Joe". Was able to completely cloth on Brunswick Heritage Pro-8 following your video. Thank You so much.

@AverageJoesPool 8 месяцев назад

Thank you for your kind words, it is genuinely appreciated! Glad to hear that we were able to help you out along the way with your cloth installation. Now you can relax and enjoy your table! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@chrisshore9000 Месяц назад

I was quoted $700 to level and re felt my pool table. I offered them $500 cash thinking that was enough money but it wasn’t so I did it myself. The company that put it together the 1st time used bondo on the seems so other videos helped with that, but this was the most helpful. Thank you.

@AverageJoesPool Месяц назад

Excellent stuff! Glad it was helpful for you! We also have video's on how to seal your slate joints using both beeswax and Bondo so you can choose which best suits. Both are available on our channel. Hope that helps! 👍

@caspervandijk9377 Год назад

Awesome tutorial. Clear explanation. Step by step this is a very easy way to cloth your pool table. Thanks for the help. Mine looks awesome!

@AverageJoesPool Год назад

Thank you, and really glad that your installation went well for you and we were able to help you out. Thanks for your support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@graemehodgson8580 2 года назад

Cheers guys (and gal) very helpful step by step guide! Keep up the good work, from over here in NZ.

@AverageJoesPool 2 года назад

Thank you, we really appreciate that :-) Hopefully we'll have lots more great content coming your way, thanks for your support!

@frankleonard2391 10 месяцев назад

Thank you! I followed your video step by step and am tremendously pleased with the results. 🙏

@AverageJoesPool 10 месяцев назад

That's awesome - thank you for your support!

@williefifer6361 27 дней назад

Hello I am a past coin machine technician and repairman I've reclothed billiards tables of all brands over 45 yrs. I was really trying to find new people to train in that area. I have reclothed in all shades of cloth backed and unbacked. thank you for having this on video.

@AverageJoesPool 25 дней назад

Thank you for sharing, and glad you enjoyed the video 👍

@lenzyg7541 2 года назад

Thank you for your help I did it and it worked out perfectly looks like it was done by a professional

@AverageJoesPool 2 года назад

Excellent!! That's what we like to hear, thank you for your support!

@fyx812 Год назад

I like how you explain the process and what it does to get a professional looking job, I'm going to be doing a felt job soon... Thanks for the video!!!

@AverageJoesPool Год назад

Thank you, glad you found the video helpful! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@MichaelJart 2 года назад

Done this table 6 times and these are the best my side pockets have ever come out!!! Thanks. Great vid!

@AverageJoesPool 2 года назад

Excellent! Glad we were able to assist, and great to hear it's come out better than ever before! Thank you for your support!

@tomjenkins8817 11 месяцев назад

Followed your instructions and just finished refelting my table. The job included replacing the bumpers and took me 4 days to finish. I think the hardest part was the bump work and your instruction were very helpful.

@AverageJoesPool 11 месяцев назад

That is excellent news - really glad that our video's helped you complete the job successfully!! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@cathalfitzpatrick9025 2 года назад

Just refurbished an old damaged table this video was very useful thanks for the help

@AverageJoesPool 2 года назад

You're welcome! Glad it helped!!

@andcrafter4790 Год назад

This video is one of the most helpfull and simple tutorials on the platform. Good work!

@AverageJoesPool Год назад

Thank you, glad you found it helpful and hope your installation went well :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@excxmoody 2 года назад

Exactly the amount of attention to detail I put in when building a poker table, even double and triple checking. Took a little longer but I was happy with the end result.

@AverageJoesPool 2 года назад

Thank you!

@Z06Fred Год назад

Thanks for the great video series. There are lots of other youtube pool table rebuild videos but none hold a candle to this series. I had no choice but to rebuild my table myself as I am hundreds of km from the nearest pro, so travel cost alone would have tripled the cost of a my rebulid.

@AverageJoesPool Год назад

Thank you, that is very much appreciated, and really glad to hear we could help you out with your table rebuild. Hope all went smoothly for you, and thank you again for your support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@0bm31770 Год назад

I was able to follow your instructions and re-cover my table. Thanks!

@AverageJoesPool Год назад

Excellent, that's what we like to hear. Job well done! :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@NM-md1yh 8 месяцев назад

Great tutorial, saved me tons of time and money!! Thanks for the help!

@AverageJoesPool 7 месяцев назад

Glad that you found our video useful 👍 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@nogribin 12 дней назад

what a superb video. i appreciate all the work involved, will be much happier paying some pro's to come do this on my personal table vs trying this myself heh. thanks + hi hi hi from spain.

@AverageJoesPool 11 дней назад

Glad it was helpful, and understand your viewpoint 100% 👍👍

@jtcowhand Месяц назад

Great craftsmanship! Your videos have inspired me to buy a used affordable pool table with confidence.

@AverageJoesPool Месяц назад

Go for it! 👍👍👍

@user-ko9sb2cg2e Месяц назад

I'm looking for a pool table that most likely will need re-covering . Your tutorial has helped understand what is involved and now I'm confident I can go ahead and give this a try . Thanks

@AverageJoesPool Месяц назад

Excellent, glad we could help and good luck with your installation 👍

@joedon1706 Год назад

Thank you for your great help. Just got done and the job turned out very well. And, as always, if I can do it....anyone can do it. :)

@AverageJoesPool Год назад

Excellent, glad we could be of help, and glad to hear that the job turned out well. Great stuff, and thank you for your kind words and support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@billybinkley6786 2 года назад

Awesome job on explaining it !!

@AverageJoesPool 2 года назад

Thank you!

@TheJemster Год назад

Thank you for creating this tutorial! Your concise instructions made my first ever felt'ng perfect!

@AverageJoesPool Год назад

That's great! Really glad that your cloth install wnet nice and smoothly, and glad we could help :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@TheJemster Год назад

@@AverageJoesPool Just PayPal'd a donation. Thx again!

@AverageJoesPool Год назад

Thank you for your support!! Hopefully we can help you out again the the future :-)

@darrengauger9218 2 года назад

Yep, best vid I have watched on pool table cloth install, and I watched several. I will watch again while I replace. Thank you! Will you be making one on putting new cloth on the rails, or am I missing it? Not finding one yet.

@AverageJoesPool 2 года назад

Thank you, nice to see our hard work is appreciated!!! Yes, the rails video is now live: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bous6ShN_W8.html

@judahjaquith6854 2 года назад

This is absolutely perfect thank you so much

@AverageJoesPool 2 года назад

Glad you like it!

@judahjaquith6854 2 года назад

@@AverageJoesPool I'm building my own pool table and now that I've finished the felt I'm so close!

@wescoleman6390 Год назад

Thanks for making this video! I used this technique to stretch some felt over a board gaming table. It looks great!

@AverageJoesPool Год назад

Excellent, glad you found our video helpful, and glad your gaming table came out well! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@ricardochrispim8250 2 года назад

Excellent content! Congratulations!

@AverageJoesPool 2 года назад

Much appreciated!

@pmp2103 11 месяцев назад

Great, well explained, thanks!

@AverageJoesPool 10 месяцев назад

Great to hear that our video was helpful for you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@jari12039 Год назад

thank you so much ! this video really helped me a lot

@AverageJoesPool Год назад

Glad we could help, and hope that your installation turned out well for you! Thanks for your kind words and support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@pootieputin2771 Год назад

Great video... one suggestion. I always leave some clorh overhang around the table so I can come back at some point and restretch the cloth. Leaving some overhang by not trimming it off allows you to grab the cloth for basically reinstalling the cloth to tighten it. By trimming the cloth, there is not enough the do a good re-stretch job. Many players like fast worn cloth.

@AverageJoesPool Год назад

Absolutely, nice tip! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@Emontop1 2 года назад

Thanks for the tutorial 👍👍👍👍👍😀

@AverageJoesPool 2 года назад

Thank you, much appreciated!

@alanmorgan09 Год назад

IF YOU WANT TO KNOW HOW TO COVER YOUR TABLE YOURSELF THEN WATCH THIS GUY, BEST DEMO ON TABLE COVERING I HAVE SEEN, I MANAGED TO GET ALL POCKETS REALLY NICE THIS TIME, THANKS MAN GREAT HELP

@AverageJoesPool Год назад

Thank you, glad to hear we could help you out with your installation! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@waynebrough8330 8 месяцев назад

Excellent video, thank you

@AverageJoesPool 8 месяцев назад

Glad that the video was helpful for you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@jaysalvacion9249 Год назад

his videos deserve a 5star..

@AverageJoesPool Год назад

Thank you, much appreciated! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@nasruallahmehmoodmashallah1055 2 года назад

Very nice cloth installation pool table 👌 😎

@AverageJoesPool 2 года назад

Thank you :-)

@2869may 2 года назад

Great video with good information..!

@AverageJoesPool 2 года назад

Thank you, really glad to hear it was helpful for you :-)

@financialzone 2 года назад

This is a fantastic presentation of the pool table cloth installation process. Thank you.

@AverageJoesPool 2 года назад

Thank you, glad it was helpful for you! We put a lot of time and effort into producing this video series, so it's nice to see it's appreciated :-)

@hobo1704 Год назад

Awesome, thanks

@AverageJoesPool Год назад

Glad the video was useful for you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@jayrobelo9877 Год назад

Awesome content you earned yourself a subscriber and a like thanks my friend!

@AverageJoesPool Год назад

Thank you! Glad you are liking our videos :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@bertblue9683 Год назад

Great video!

@AverageJoesPool Год назад

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@paulnielson2629 Год назад

Thank you very helpful, do more videos

@AverageJoesPool Год назад

Thank you! We definitely have plenty more video's to come!! Please make sure you#ve subscribed and have notifications switched on. Thank you again! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@coatingkings 2 года назад

Thank you Sir!!! 🍻

@AverageJoesPool 2 года назад

My pleasure!

@toddpeterson Год назад

I love your videos.

@AverageJoesPool Год назад

@bobbevins8946 2 года назад

Great Video

@AverageJoesPool 2 года назад

Thanks! Much appreciated!

@stephengordon5754 2 года назад

I hope you get some more views! Great Videos!

@AverageJoesPool 2 года назад

Thank you! We're hoping so too!! We're still pretty new, but making ground. Thanks fo ryour support! :-)

@guiso1973 Год назад

thank you so much!

@AverageJoesPool Год назад

Glad we could help you out! :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@tiny951 Год назад

Thanks!

@AverageJoesPool Год назад

Thank you for your support - glad we could help you out :-)

@jeffthornton2229 Год назад

Got a free pool table the other day 7 ft but still cmon lol.. picked it up and it’s mostly good except the felt was trash. Followed this tutorial mostly to a T. Turned out fantastic. Had to comment my thanks

@AverageJoesPool Год назад

Awesome - glad to hear that the video was useful for you. And glad we could help you out! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@didster2000 4 месяца назад

Simply outstanding video!! Thank you. However, I am confused about where the stretch calculations from your other video come into play. I plan on doing mine in a couple hours if anyone has ay input for me that would be greatly appreciated.

@AverageJoesPool 4 месяца назад

Thank you for your comment! Just to clear up any confusion, we are currently putting together a newer and more advanced version of our cloth installation video, which will utilise the stretch index method. The stretch index can be very helpful when you are fitting high-end worsted cloths that have very little give (such as Simonis) as they can be very unforgiving. The new more advanced video is NOT designed to be a replacement for our original cloth installation video. Instead it is designed for people who want to delve a little deeper and/or are installing cloths such as Simonis. It's likely that 80%+ of cloth installations done on pool tables are done without utilising a cloth stretch index method, by a process identical or similar to the process shown in our original video, so it will remain relevant to the majority of people who want to do a DIY cloth install. But if you are installing Simonis (or similar top-end worsted cloths) then the new more advanced video (which uses stretch index) would definitely be a good option. The process is slightly different if using the Stretch Index method, simply because it HAS to be due to the requirements of the process. But you can use either method, original or advanced. They both work! Hope that helps! ----------------------------------------------- To help support us: 1) Please be sure to use our Amazon Links! 2) Please ensure you LIKE our video's, and SUBSCRIBE to our channel! 3) Donations always welcome! Hit the SUPER THANKS option below the video on RU-vid! Thank you for your support!

@Nutsofamily Год назад

Thanks for extremely well done videos. Can you please recommend a worsted cloth from Amazon Canada? So many conflicting reviews Reg ball marks and creases!

@AverageJoesPool Год назад

Hey there! Thank you, glad you are enjoying our video's!! With regards to cloth, budget is always a factor. Pretty much the best of the best is Simonis cloth, but it does (naturally) come with a higher price tag. We have added links to several cheaper options on Amazon (including amazon.ca!) into the video description if the budget is tight. Yes, cloth reviews often vary from great to terrible, and this often seems to be linked to the experience that the person had fitting the cloth rather than the cloth quality itself. On cheaper cloths expect ball marks (burns, white spotting). You get them on expensive cloths too, but they tend to be more resilient (Simonis make a 860HR cloth and the HR stands for High Resistance, designed specifically to reduce white spotting). Hope that's of some help!! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@scooterk1940 3 месяца назад

Thanks for the informational video. The problem I have is my Kasson pool table doesn't have the wood backing on the slate pieces, so it needs to be done with adhesive. Any videos on how to do that?

@AverageJoesPool 3 месяца назад

Hey there! Unfortunately we do not currently have a video for the glueing method for pool table cloths, only the staple method as shown here. Sorry we couldn't help this time 👍

@benstumpo5145 2 года назад

@Fix Savers many thanks for your advice. I have installed based on this video and the cloth turned out really good. The middle pockets were heart wrenching. I have noticed that there is a small amount of slack around the middle pockets area. Nothing disastrous, but there are some waves there when you run a pushed finger around the area. Any advice for getting rid of that. IE, I would need to move one staple at a time to make any corrections to get rid of it, but which ones. From the table sides or directly below where ripples are on the curve of the pocket?

@AverageJoesPool 2 года назад

Yes, the centre pockets are probably the worst part o fthe job as you are dealing with a 180 degree curve rather than 90 on the corners. Hard to know the best solution without seeing it first-hand, but the important thing is to remember that the cloth is pulled in various directions during installation, so you need to be careful removing any staples, and don't remove too many at a time. It may be worth carefully removing a couple from the centre of the pocket on both sides (get someone to help) and try pulling the two centres out and see if this gets rid of the ripples. If not, it is likely another angle causing the issue. Worst case you should be able to remove all of the staples from inside the centre pocket and pull from various directions to see where the issue lies. Once you have found it, you could also try some spray glue carefully underneath the trouble area to help stick that down as you recorrect the tension. It's one of those PINA jobs where you have to play around with it a little, but being careful not to release too much tension anywhere as you may not be able to replicate that tensioin again (well, not easily!). Hope that's of some help!

@8Scorpions 10 месяцев назад

Do you also have a video on a simple level technique for the table as well?? Thanks for the video!!!

@AverageJoesPool 10 месяцев назад

Indeed we do! Here is our video for levelling the frame: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HyXCsk8_n_A.html and here is our video for levelling the slates: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V-GfbSnjGtg.html - hope they are helpful for you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@FingerJam12 Месяц назад

dont know about full guide but thanks for what you did show.

@AverageJoesPool Месяц назад

Please be sure to check out our latest video on cloth installation, it might have more of what you were looking for: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-s4mH1Lw104I.html ----------------------------------------------- To help support us: 1) Please be sure to use our Amazon Links! 2) Please ensure you LIKE our video's, and SUBSCRIBE to our channel! 3) Donations always welcome! Hit the SUPER THANKS option below the video on RU-vid! Thank you for your support!

@cesara4979 2 года назад

Very good video, im about to help a friend to do his table. What brand is your staple gun because that one in the link is very similar but not exactly the same one, and i would like to get the same one bc the tip is a little different ?? Thanks again

@AverageJoesPool 2 года назад

Thanks for the message. Actually this model is only available in Canada, BUT there is a very similar model on Amazon USA with the same tip type (more accurate). We have updated the Amazon links in the video description. Please take a look and try again - thanks for your support and best of luck with the installation! :-)

@martinemmerson2809 4 месяца назад

Do you have a video of the table rail installation? How would you ensure the rails are centred on the slate pockets, square and straight.

@AverageJoesPool 4 месяца назад

Yes, indeed we do. How to ensure that the rails are square and pockets are even during rail install is covered within our complete Pool Table installation video, which is here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mIem08KAPkI.html Hope that helps 👍 ----------------------------------------------- To help support us: 1) Please be sure to use our Amazon Links! 2) Please ensure you LIKE our video's, and SUBSCRIBE to our channel! 3) Donations always welcome! Hit the SUPER THANKS option below the video on RU-vid! Thank you for your support!

@piokul Месяц назад

I really appreciate this video! One question though... How do you tell which side of the cloth is the playing side?

@AverageJoesPool Месяц назад

The playing surface is smoother, whereas the rear will look a touch fluffier. You may want to check out our new cloth installation video (specific for worsted cloths) as this shows the difference as an example, watch from 8:00 onwards for the clips that compares front and rear of cloth: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-s4mH1Lw104I.html Hope that helps! 👍

@piokul Месяц назад

@@AverageJoesPool Thank you! I got my cloth now and it has an embroidered edge, so now I have more indications than I need ;)

@user-fz3bs4mf7w 8 месяцев назад

Hey great video! Just a question do you first staple the side of the table then move to the end or do both sides first then the two ends ? Or it doesn’t really matter ?

@AverageJoesPool 5 месяцев назад

Thank you! You should follow the order shown in the video, so starting on the ends first. 👍 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@tonyde9ball 2 года назад

Shot bruv ive done plenty of tables over the years and ill be adding something new to the tool box as of today. The wifes nail polish lol

@AverageJoesPool 2 года назад

Nice! :-)

@DcDouglass84 7 месяцев назад

Is it better to order felt to be more then you need so it's not as short when doing the other side?? Like ordering for a table that is a foot bigger, atleast then you can trim afterwards if needed

@AverageJoesPool 7 месяцев назад

Yes, absolutely. However, when it comes to more expensive cloths the difference in price to go up by one size can be considerable and so not always practical cost-wise. But for more budget-orientated cloths the price difference would not be massive, and so it's a option definitely to be considered! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@BergKnowsBest 2 года назад

I'm about to do my first recover. I have seen other videos where they start from the middle pockets and stretch, work their way out to the corners. So which is best - end-to-end as you show or center out to corners? I'm sure there is more than one way to skin the cat. I'm just looking for best practice so I only do this once.

@AverageJoesPool 2 года назад

Well, we'd recommend it the way we've done it, but of course try it other ways too and be sure to report back on your experiences for other viewers. Thanks for watching!

@toddembry3792 2 года назад

Follow this video and you will be fine

@sharune007 2 года назад

Can you do a video on changing the rubber rails? Thanks.

@AverageJoesPool 2 года назад

Not right now, but we may cover that in the future!!

@bruce6620 2 года назад

Check out Creative restorations for a rail replacement Doug Giles has a great video.

@MCash7709 Год назад

I have a question. One of my shims has moved from under the slate and caused it to droop some and come out of level in one corner. Are you able to partially lift some of the felt, enough to relevel the slate, then just retighten it and staple again or do you need to redo the entire piece of felt?

@AverageJoesPool Год назад

Well, once out of alignment it should be levelled again really. You could try to re-shim just the part where the old shim failed, but you're unlikely to get it perfect, and the seam may well have cracked it's beeswax seal due to the drop. But if you do want to try it and see, you should not need to remove the cloth at all to level the slate. The slate should have timber backing (which you staple in to) like in this video. The shims go underneath this timber frame, so sit between the table frame and slate timber frame. So you should not need to remove any part of the cloth if you want to try and re-shim as a quick fix to see you through. But really you'll want to level up the slates afresh, which means cloth removal and re-sealing the seams. But for a quick temporary fix you could try it. Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@sharkymoon422 Год назад

Do you fill in the holes on the slate near the edges or just cover them as they will be under the cushions?

@AverageJoesPool Год назад

No need to fill any holes that will be under the rails. If the ball can't touch the hole, then you don't need to fill it. Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@juliemstevens 6 месяцев назад

Do you have to iron the felt? The fold marks pull out?

@AverageJoesPool 6 месяцев назад

No, the cloth should not need ironing (and should never be ironed on the table). Any fold marks will definitely stretch out during installation so there's no need to try and iron them out beforehand. Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@brett6314 Год назад

I just got Predator Acadia select cloth. There are some creases where the cloth was folded. The corners are somewhat pronounced wrinkles. I'm very much wanting to iron these out. A little research says low heat is safe. Should I? Is it necessary? They are much more pronounced than what I see here.

@AverageJoesPool Год назад

Hey Brett! Well because the cloth is going to be stretched a fair bit it's unlikley that those creases/wrinkles will still be there during installation. You should be able to iron them out on low heat if you prefer, just keep it low heat and keep the iron moving. But it likle;y won't be required. Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@drumrooster 4 месяца назад

My table is 1" 2 peice slate but it dont have the wood strips under the outter bottom edges to staple the cloth too? Has someone removed them? My last cover I had to glue on with clamps..should I put the wood strips on it?

@AverageJoesPool 4 месяца назад

Yes, not all pool tables will have the slate backing. Most do, but not all. The other method for re-clothing is gluing instead of stapling, which it would seem the manufacturer of your table intended. The process is different though, and unfortunately we do not have a video for the gluing method so you'd have to have a good search around RU-vid and see what's out there. I would recommend against adding the timber backing retrospectively as this throw up issues such as overall table bed height, the skirts may not be long enough to hide the slate edges anymore when raised etc. We hope you find a good guide for gluing. Best of luck! ----------------------------------------------- To help support us: 1) Please be sure to use our Amazon Links! 2) Please ensure you LIKE our video's, and SUBSCRIBE to our channel! 3) Donations always welcome! Hit the SUPER THANKS option below the video on RU-vid! Thank you for your support!

@MC-vr2fl 6 месяцев назад

Hi there. What kind of wax did you use?

@AverageJoesPool 6 месяцев назад

Hi there! Please take a look at our How to Seal Pool Table Slates video as that covers the process and what type of wax to use etc. The video is here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-wZmM9sJeCXc.html --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@stevehunt9114 4 месяца назад

Thanks so much really appreciate all those tips the center pockets didn't go as well with the felt I bought off amazon but you tip helped save the day. do you have a email address that I can send a thankyou retransfer to

@AverageJoesPool 4 месяца назад

Glad we could help you out with your installation! Absolutely, you can make a donation at www.paypal.me/thanksfixsavers or alternatively you can click the Super Thanks button under the video and donate via RU-vid. Whichever works best for you. Thank you for your support 👍

@stevehunt9114 4 месяца назад

Sent by pay pall. Thanks again apricated all the time you put into the video @@AverageJoesPool

@AverageJoesPool 4 месяца назад

@@stevehunt9114 Received with thanks! Thank you very much for supporting our work, and we hope we can help you out again in the future!

@kevinmchale5660 2 года назад

One thing to mention perhaps is cutting the cloth for the rails if your cloth comes all 1 piece. Mine was just barely enough and I wasn't super careful to keep the max I could now I am short enough clith to do 1 rail. Shieks.

@AverageJoesPool 2 года назад

Yes, cutting the cloth yourself can be troublesome which is why we recommend to set a cloth that comes with the rails pre-cut whever possible as it saves a lot of extra hassle and possibility of mistakes. Cloth manufacturers can be very stingy, and so there is usually next to zero extra so you have to be accurate with the measurements and cutting. Sorry to hear that you mis-cut - that's a nightmare! Especially as you cannot usually just order one rail cloth, you usually have to re-order a full second set and that's costly!!! It may be worth contacting the manufacturer, maybe they can help you out. Best of luck!

@kevinmchale5660 2 года назад

@@AverageJoesPool thx. Perhaps a video on replacing the bumpers. Daunting cutting the ends to the proper shape. Great videos. I watched them all more than once.

@stephiboy61 3 месяца назад

i use a soldering gun to burn the bolt holes out it prevents unravelling

@AverageJoesPool 3 месяца назад

That's an interesting solution. It should seal the edges pretty well 👍

@jackoconnell5524 2 года назад

What psi reading did you put your compressor to?

@AverageJoesPool 2 года назад

You can leave your compressor on the standard default. No need to adjust for the stapler. Hope that helps!

@barbl4297 Год назад

Nothing is working to get the wrinkles out around the side pockets. We have Predator cloth. Any advice?!?!

@AverageJoesPool Год назад

Hey there! Usually if you find you are repeatedly getting wrinkles whilst you're confident you are doing everything right, it can be best to rewind a little. The cloth may not be stretched quite right in a certain direction before you got to the side pockets. If you undo a few staples at a time you'll be able to pull the cloth slightly more in that area and see if it makes the wrinkles disappear or get worse. The pull may be required at an angle you would not expect, hard to know without having it in front of you. But that would be a good route to take, try and find the source of the issue rather than fighting against something that's not quite right. Hope this helps!! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@rjaycagayan5766 2 года назад

What brand your staple gun?

@AverageJoesPool 2 года назад

Actually there are links in the video description, here they are again: Looking for tools and supplies? Air Stapler: amzn.to/3k0DQhE T50 Staples: amzn.to/3k20OVD Felt Cloth: amzn.to/2VsIVFt Worsted Cloth: amzn.to/3e2eX1q

@johng-840 2 месяца назад

Are heading protecting required?

@AverageJoesPool 2 месяца назад

Do you mean ear protectors? It depends on your preference. I always wear them whilst using power or air tool of all kinds, and in the location of this table the ceilings are quite low and no soft furnishings and so you get a lot of noise. But most people are happy to use air staplers without ear protection, whatever you prefer personally 👍

@GoldwingTrailer 7 месяцев назад

Cloth developed wrinkles around the center pocket after the holes where cut into the cloth.........did not appear right away but the hole looked distorted after cutting...........I used nail polish to finish the cut around the hole...........I cut the holes by inserting a tube into the bolt holes and hampering on the tube with a hammer to cut the cloth..........what is the best way to fix this? thanks

@AverageJoesPool 7 месяцев назад

My guess would be that by hammering the tube into the hole to cut the cloth you would have stretched the cloth, hence the hole now looks distorted. The holes should be cut with a knife or scissors. The only way to fix this would be to see if you could re-stretch the cloth a little by undoing the staples one area at a time and taking up the slack. And then re-cutting the holes but this time with a knife or scissors. Not a hammer and tube. Hope that helps! 👍 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@GoldwingTrailer 7 месяцев назад

Clarification, I did not stretch the cloth to cut the hole, the process is similar to die cutting where the cutting surface the sharp inside diameter of a tube is held against the bottom of the cloth and does not stretch or raise it off the surface of the slate and then a ball peen hammer ball end is used to lightly strike the cloth pinching and cutting the cloth against the sharp inner edge of the tube thereby cutting the fibers very easily. Forms a near perfect hole in the cloth slightly smaller in diameter than the hole itself since the tubing is inside the hole and fits tightly. I assumed that cutting the hole with a knife and scissors would cut all the fibers around the hole similar to the way the die cutting works and if so then I would expect similar problems with the knife and scissors method. I'm thinking I could have super glued (or glued) the cloth to the slate around the hole prior to cutting the hole. I also discovered that the wrinkles are coming and going away with temperature. It is currently start to drop from the 70's F to the 50's F. Thanks for your prompt reply and excellent video. @@AverageJoesPool

@donaldprimm6164 9 месяцев назад

Do you have a video or installing the new pockets?

@AverageJoesPool 8 месяцев назад

We don't have a video dedicated to that, but if your pocket type if the same as this table you should check out the full install video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mIem08KAPkI.html as this shows putting the rails and pockets together. The pockets themselves (this type) are quite generic and so it's usually very easy to find replacements (Amazon etc). Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@fearsomefox23 2 года назад

Do you have steps for recovering using simonis cloth?

@kennethcrouse6212 2 года назад

much less stretch with simonis. requires strong hands lol. Other than that it's the same. Covering a table with cloth that has a nap (like snooker cloth) takes a slightly more precise technique as it tears very easily.

@AverageJoesPool 2 года назад

The basic principal is the same. Simonis tends to have very little strech to it so a couple of extra tools including a pair of canvas stretcher pliers come in very useful (we did the one if this video by hand as the most DIY-orientated way as that would be most applicable to most viewers). We may do a seperate dedicated Simonis installation video in the future if we get enough support, but for the most part the basic principal is the same. Hope that helps!

@masongreen2284 Год назад

I think I may have found my new business idea! Now what to charge for this new knowledge!?

@AverageJoesPool Год назад

Best of luck!! :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@palmer7203 5 месяцев назад

I’m not sure if someone commented on this already, but it would be nice to have reference to the stretch index for the cloth on this particular video. It doesn’t seem to use it or reference it.

@AverageJoesPool 5 месяцев назад

Thank you for your comment! Just to clear up any confusion, we are currently putting together a newer and more advanced version of our cloth installation video, which will utilise the stretch index method. The stretch index can be very helpful when you are fitting high-end worsted cloths that have very little give (such as Simonis) as they can be very unforgiving. The new more advanced video is NOT designed to be a replacement for our original cloth installation video. Instead it is designed for people who want to delve a little deeper and/or are installing cloths such as Simonis. It's likely that 80%+ of cloth installations done on pool tables are done without utilising a cloth stretch index method, by a process identical or similar to the process shown in our original video, so it will remain relevant to the majority of people who want to do a DIY cloth install. But if you are installing Simonis (or similar top-end worsted cloths) then the new more advanced video (which uses stretch index) would definitely be a good option. The process is definitely slightly different if using the Stretch Index method, simply because it HAS to be due to the requirements of the process. But you can use either method, original or advanced. You can pick and choose, watch both and do whichever you like the look of, they both work! Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on RU-vid (by clicking Like!) 3) Please ensure you subscribe to our RU-vid channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@Oshane_smith19 Год назад

How you installed the banks would be well appreciated

@AverageJoesPool Год назад

Hey there! We have done a full pool table installation video which shows the installation and alignment for fitting the rails to the table. That video is here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mIem08KAPkI.html However, if you mean how to replace the rail rubbers, we have not done a video on that yet. Maybe in the future! Thanks for your support :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@JoeWooldridge2 2 года назад

How different is installing Simonis 860HR?

@AverageJoesPool 2 года назад

@Ken_aka_Ice Год назад

@@AverageJoesPool Great video! Hoping you do a Simonis recover soon. Thanks for the great tips and videos!

@AverageJoesPool Год назад

@@Ken_aka_Ice Thank you!

@oOohdaddy 2 года назад

So you eont need a 3M spray glue at any point?

@AverageJoesPool 2 года назад

Not for the staple installation method. There is a glue method where the cloth is glued rather than stapled. Spray glue is usually used on the pocket liners though (link to that video is in the video description on this video!) Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@Seohelpnow Год назад

What about felt on bumpers

@AverageJoesPool Год назад

Here's the video you need for that: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bous6ShN_W8.html 🙂 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@oOohdaddy 2 года назад

I have cheap sportcraft pool that i took appart to refelt the sides and the top well after cleaning railsand removing old felt from one of the sides i have come to conclusion that my sided dont have removable trim piece that holds felt in place looks like the whole thing was put together in pieces and stapled and glued and not meant to be changed just use and discard i believe , on the other hand i could be wrong which im hoping i am so please if someone has done one of these shed some light

@AverageJoesPool Год назад

I've never worked (or played) on a Sportcraft table. Are they slate top, or wood? A lot of the cheaper wood tables are indeed often glued and stapled and not really meant to be 'maintained' ongoing (or to really last he test of time). Hopefully someone reading will have experience of Sportscraft tables? --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@jarespeoples554 Год назад

Call me pops. I have the same sportscraft table. How did you job turn out? Were you able to refelt the table since it is not slate just wood underneath? I was thinking about refelting but now now I think the table is not worth the felt. Let me know. Thanks

@jarespeoples554 Год назад

@@AverageJoesPool the sportscraft table is wood. Is it worth replacing the felt? The cost of good felt maybe more than the table.

@oOohdaddy Год назад

@@jarespeoples554 go for it it turned out awesome, i got new pockets old ones were so fragile that brackets broke off so i replaced those , they are not same you will have to do some modification on the table to fit it you will see once you get to that stage you will know what to do once you get there it does take a long time but i was determined to finish it so if you are same as me in that field than i say go for it i went from having 200$ table looking like 3000$ one i even aded neon strip lights that i put under the edges that are battery operated i was able to tuck it all under so none if it visible only the light glow shows not to mention i crushed my table sides when i was loading it on the truck so i had to do some bondo work on the pannels even after all that turned up awesome wish i can upload photos of it so i can show you

@jarespeoples554 Год назад

@@oOohdaddy ok now you got me curious. Thank you for responding! U care to share a few photos via email?

@ajfanotreally2523 Год назад

1. If the slate has wood underneath use tac nails, staples are horrible and look awful on a pool table. 2. If the slate has no wood then use a approved adhesive glue for the felt and slate.

@AverageJoesPool Год назад

Actually you don't see the staples at all once the table is back together with the panels/trims installed so cosmetics is not an issue for staples. Hope that helps !

@paulbailey5699 Год назад

Is there a video for using glue? Instead of a staple gun?

@AverageJoesPool Год назад

Hi there! Currently we have only doing a video for the stapling method, not for glue. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@swedishkev 2 года назад

Hi there, could I just ask your expert opinion? I have just bought an 8ft snooker table from a company here in Sweden. They class it as a pool table but it is exactly the same as an English snooker table.It comes with 6 legs and 3 slates,4cm thick. I have bought an 9ft table from china in 2011 , so have some experience with these tables. Now this 8ft to my surprise has no screw holes on top,to screw all those wood pieces on, for stapling the cloth. This to me is weird, there are no videos on youtube where you don't have holes on the snooker tables. So there is no holes to even keep the slates screwed down. Also, the slate looks more like a type of marble and the two slates are different looking to the other one,and one is a bit smoother. I am complaining about this to the company, I don't think they have forgotten to include all the wood bits for the edges of the slate underneath obviously. I am sure their thinking is that the cloth is to be glued on, like most pool tables nowadays. But to not have screw holes to keep the slate from moving, seems a bit ridiculous.. I will glue a bit of paper with superglue on the seems,but do you think I should just use silicone under the slates to stop them from moving. I want to use the stapling method for stretching the cloth and am not going to glue it down. Was thinking of getting the wood strips and gluing it all underneath, should work. Have you seen tables with no screw holes? Kind regard Kevin

@AverageJoesPool 2 года назад

That does sounds very odd! The slates must be attached to the base frame in some way, hence they usually have the screw holes so they can be screwed directly on to the base frame. And the three slates should definitely not be made from different materials - none of that sounds good!!! You should ask the manufacturer how the slates attach to the base frame and see what they say. Yes, you should be able to attach timber to the underside of the slates (using a good construction adhestive) if you want to do stapling, but this will raise the height of the slates above the base frame and so it may no longer fit the additional decorative trims as it should. Sounds like a nightmare TBH!!! Best of luck!

@swedishkev 2 года назад

@@AverageJoesPool All sorted, Yes very odd no screw holes on 3 piece slates. I have glued wood all around the slate, so l could staple. So now the slates can not move and all more secure when all cushions are screwed on also. As a 3rd precaution ,used a strong silicon underneath that will also hold the slates onto the frame and stop it all from moving. Not as good as being screwed down, but is working fine. One of the slates that was a different type, has not made any difference. I had complained about everything and got 40% off the price.

@jeffreylynds7986 Год назад

I’m watching this and I don’t even own a pool table

@AverageJoesPool Год назад

Glad you enjoyed the video :-)

@Eurobunneh 10 месяцев назад

I bet you’ve got thumbs of steel!

@AverageJoesPool 10 месяцев назад

Lol, pretty much 🙂 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on RU-vid and donate that way too! 2) Please ensure you subscribe to our RU-vid channel. 3) Please Like our video's on RU-vid (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!