How to Install and Configure an Allen Bradley Powerflex 525 Encoder Module 

I messed up on the scaling at 3:45 and stated 333 (20,000/60). It should have been 342. 10,000*60/1750 = 342 pulses per revolution

Are you any closer to the positioning video? I’m super intrigued about it after looking at the prices of servos and servo controllers

Hey Tim, I love the videos and I have recently built a control panel that feeds rolls of various materials through a pinch roll and cuts them at a custom length using a micro 820 with a hsc card for an encoder to get the sheet length, a pf525 and a hmi using nothing more then your videos and some help from a family member. I had a some trouble knowing the order to do stuff and the whole process so could you make a video about how you look at a job, what you do and why you do it and your whole process?

Hi Tim, Just to comment that I tryed 10+ times to configurate with CCWDE Ver 20.01.00, and never got the speed (was reading th encoder speed by d378 but o moving, until I write the parameters by keypad, then works. regards, and thank you por helping, you are practical Enginner, Cheers

I like plugging in the handheld to dsi to configure

Hello Sir, could do you please demonstrate a system to control position of a system which include vfd,encoder,proximity sensor and PLC together? its configuration both in vfds and plc

great video my friend

Would love to see a positioning video I’m actually working on a project now but can’t find any documentation on how to set it up any input would help thanks

Hey Tim, did you ever create the positioning videos involving the powerflex 5 series?

Hi Tim, could u please tell me, what is the procedure, " the motor was running with power flex 750 and encoder, Rexroth 317207, and the motor was burned, " we replace the motor with exactly one but the encoder has a different part number encoder number Rexroth 330889 ( looks like same). NOW WE HAVE AN ENCODER FAULT ALARM. please let me now what to do. should i set the parameter again? best regards

Hi Tim, Why 60? where do you get that from? Thanks

Hi Tim, a question. I have a PowerFlex 755 Frame 2 Drive. In it I have a 20-750-UFB-1 card, the manual says that I should use 20-750-S1 but I only have a 20-750-S. Is it possible to use 20-750-S?

anyway thanks tim

I have a AB 525 that I have set up to a 2 wire start. But it doesn’t stop when I open the Circuit. Can you help me?

Hi Tim, so here at work we have Powerflex 40 and powerflex 525. When ever we have a power blip or a power outage we always lose a few drive but only the powerflex 40 never the 525. do you know why that is?

Hi Tim, I enjoy and learn many things with your Videos. I have some question. I do have 2 Allen Bradley VFD one 525 5 hp other one 753 50 hp. 525 is used to take up for spiral cooler main drive is 753. I like to install encoder on 753 will be the master and 525 is slave. Can you help me on this. Thanks, Ara

Hey Tim, can you make a video of using virtual machines for plc programing

thankks

so in this application the encoder controls the speed of the vsd?.....i haven't come across an application but is there application you would know?...its a first for me..lol

Toda linha 525 aceita essa placa do encoder?

If you slide the top cover forward first it comes apart with much less effort. If you finish the playlist (show positioning and control with a Micro850) then make the playlist one video, I would throw you some cash for that.

Hello Tim, How are you, hope you are fine during these days. I need a little help as i am beginner in rslogix5. in my program i have data file f8:xx, it show usage 'X' when i click on usage tab, but when i try to find it with 'find all' it shows nothing. kindly help it would be so kind.

20,000 / 60 = 333