What is the shaft length on that? I'm installing a 54 or a 60"on my 17' mako pro skiff. It has 19" to the water from the mount. Do I need a 60" or the 54". Thanks Great video
Thanks for watching the video dude! Good eye! We did actually silicone the exterior bottom fastener array, which did include a nylon size matched washer and a small dab of silicone. Filming a process like this is very different and lots gets edited for time and/or gets done when camera is off. Regardless, your comment is 💯 relevant and again, good eye!
How about a review on that terrova! Thinking about replacing an old Minn Kota on the boat I just bought. That Terrova come with a cordless foot pedal to??
That "GPS puck" you are speaking of is not a GPS. It is actually a digital compass known as a heading sensor. The heading sensor does not receive any GPS signal. What it actually does is tell the motor board where the back of the boat is pointed so your spot lock becomes hyper accurate and allows the motor to better compensate for wind and current.
@@bsummit826 I did not, but the installers at Accurate Marine sure did. Sometimes videos get compressed for time to fit RU-vid, shots get left out. Minn Kota does a great job of providing detailed instructions for that sensor. Also, the location for mounting changes with every boat, so its best to find the spot on your particular vessel to install. Its very simple, 2 screws, 1 hole to pass wire through and a positive and negative wire.
If I mount my new terrova on the starboard side can I turn the head and motor 180° to secure it after deploy? Intent is as you mentioned, keeping the head inside the boat.
when reviewing several of these videos on installing terrovas... i've run into a bunch that say the shaft collar (or the inside edge of the semi-circular notch in the aluminum base of the motor should be at least 1.5" from the gunwale of the boat. After installing... that looks like excessive protection of the motor shaft. 1.5" from the shaft looks like it should be enough clearance. When you mount these... what is your clearance to the shaft the the mount collar?
They always try to adhere to the manufacturers recommendations. The manufacturer is looking to avoid any contact with the rub rail or hull and motor shaft which is why that distance is provided. A lot of times it comes down to the design of your boat and how your fasteners will be placed through the deck. This particular install followed Minn Kota's recommendation exactly as fastener location was not an issue.
@@thetravelingcaptain I loved this video and tried to follow it exactly and had issues with the plate too close to the edge. I disagree with you and the video in that Minnkota actually states with the shaft down there should be a minimum of 1 1/2 inches from the gunnel to the SHAFT when deployed!. If you use a plumb bob to have the inch and half clearance from the aluminum resting place, you will have 2 1/4 inches clearance to the shaft. This is due to the 3/4 inch collar on the shaft. This should be clarified as that 3/4 inch makes a huge difference in mounting
@@bobhoffman1869, as mentioned multiple times in comments, your install may differ from the one in this video. Unless you own a Beavertail skiff, the shape of your vessel's bow may not be like the one in this video. The installers followed Minn Kota's guidelines and completed a successful install. This vessel is still running around with the same troller on the bow and no damage from it. So, allow me to state this again, your install may differ from the one in this video. Please read all of the directions provided by the manufacturer before attempting to start your project.
You have your way of marking your work and Accurate Marine has their way. Both will arrive at the same destination. Please feel free to install hundreds of trolling motors your way just as the guys in this video do it their way.
Are you wondering about the heading sensor for the Ipilot? That was installed on centerline of boat just forward of motor. Not much to show other than 2 screws and pos/neg wire. Sensor uses wireless connection to Terrova.
This is 100% A++ and done on a professional with critical "need-to-know" info to install the Terrova unit. Thanks a million guys. Well Done!! I will be doing this install next week and will have this video up on my chromebook side by side with my work area.
So, when did the power plug get installed??? Factory?? Reason I ask is that I do not have a power plug on my boat...would have been nice to see installing to battery n plug install
Which part of the running would you like to have seen? It is zip tied under starboard side gunnel in an area manufacturer ran other cables to rear of skiff. Minn Kota provides a long enough cable to get it around your boat to console. Trolling motor has a shorter length cable that then attaches to extension which is connected to Solix 10.
@@chandlerhill6453 Long arms through a small access area inside forward hatch. Every vessel installation is different so there is honestly no need to show exactly how it is done. Unless you own a Beavertail Vengeance, will not be the same.
This video was about installing a physical electric motor on the vessel. Battery wiring instructions are provided in box for you by MinnKota. Read all included instructions and please take care when connecting power. Batteries connected in 24Vdc create enough current to do extreme damage.
Thanks for the video, I see you recommend a deka agm battery, which group size for the terrova? Is a lithium battery worth the investment on a terrova?
Yes there is a tool to trim cable ties off. It is available at West Marine or on Amazon. You can also buy self trimming cable ties which do to require a cutting tool. Those are also available from same vendors.
Hi , great video, I have a new ulterra that I’m having issues with and have no faith in it, I’m waiting on getting a new terrova, the ulterra is a 36 112 60” on a quick release, can I just put a terrova 36” 112 60” on that same quick release and be done with it? Thanks in advance
@@mikebromelow8514 Your point is valid, but don't worry that part of the job is very simple. Minn Kota provides detailed instructions on how/where they recommend you install sensor. All vessels are different and your mounting location will most likely differ from this one. It is highly recommended you read all of the included installation instructions before proceeding with your own. Thanks for watching this video.
@@BruteManny Unfortunately, there was not enough room to fit anything but an arm and tool through the access point to reach bolts. The installer put his whole body in hatch then reached through that access point to put nuts on the bolts. I understand how important this is and will take your request in to consideration for future installs and make sure to show you how to put a nut on a bolt.
Thanks for watching the video. I’ll get with my hairdresser and see if there is anything I can do to hide the scars on my scalp and then maybe I can meet with your approval. I’ll follow up with you after I get it all done.
Silicone is NOT the correct sealant here, in fact other than working around wind sheild glass, silicone has no place on a boat, not even "marine" silicone. 3M 4200 (not 5200) would be a much better choice, or maybe life caulk. The best way to do it would be to overdrill the holes a little then pot them with thickened epoxy, then redrill them and seal with 4200. They will probably be OK here on the Beavertail since it is no wood construction, but it's a disaster to this on a boat with a wood core. You are asking for core rot in a few years to do it this way. I'm surprised that pros don't know this.
In your professional opinion why is 3M 4200 a better choice? Have you consulted a representative for 3M who advised you on proper sealant for this particular job? 3M Marine silicone is a valid choice for this install where it is above the waterline through closed cell foam core and fiberglass substrate. Adhesive properties of 4200 are not needed for this type of work. As far as your comment on "drill and fill" technique, this is not the type of job that would require you to do it. The puck part of the quick release bracket an large fender washers below provide enough strength. Just make sure to use the correct Minn Kota quick release bracket for the 80lb thrust and below motors or HD version for 112lb thrust motor.
Deka AGM batteries, they came with boat from manufacturer. If purchasing for your own use, choose a good quality AGM battery brand with nation wide warranty.