How to install R.O. UV Filter with Flow switch.

Подписаться 2 тыс.

Просмотров 21 тыс.

50% 1

How to install an automatic start - stop flow switch / flow sensor to a UV filter
and how to install it to an existing Reverse Osmosis Water Filter System.
0:00 Introduction
0:58 INSTALLATION OF GLASS TUBE
2:11 WIRING CONNECTIONS
3:55 INSTALLATION OF FLOW SWITCH
4:46 U.V. LAMP INSTALLATION
6:19 INSTALLATION OF PRE-FILTER
6:51 INSTALLATION OF UV FILTER
9:28 Use of UVC Test Cards
Also included in the video, how to install a stainless steel mesh washable pre-filter.
If you have any questions, just leave it on the comments below.
If you liked this video, please don't forget to like and subscribe, and please hit that bell button.
Thanks for watching, till next time. :)
Please watch:
Reverse Osmosis water filter installation Tutorial.
• How to Install Reverse...
Click here to subscribe:
/ @jongpenaranda
#uvsterilizer #reverseosmosis #flowswitch

Опубликовано:

2 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 48

@garryboi15 2 года назад

Very good tutorial but this will actually shorten the lifespan of your CCFL UV lamp.. You can actually do the same function using motorcycle horn relay, mas safe pang gamitin compare sa flow switch that is running on 220V AC. "When the electrodes no longer emit sufficient electrons, the light burns out. As startup rapidly depletes the coating on the electrodes due to the high voltage required to get an arc going, frequent startups will shorten the life of the bulb."

@jongpenaranda 2 года назад

Hi, thanks for the proactive input. That quote is applicable to larger UV systems which consumes higher wattage, but may also have less effect to home units since were using ''electronic ballasts'' nowadays. However, overheating of UV lamps also damages the coating due to continuous operation which is caused by less flow of water as cooling (in which has more disadvantages). If you have enough flow of water to cooldown your system or you're in colder areas, then this flow switch is not necessary. I myself in tropical area, using this design is more efficient when it comes to temperature issues and lesser electric consumption.

@jongpenaranda 2 года назад

And for the flow switch itself, I have used in this video is a magnetic type switch. Which means the mechanical (water) side is totally isolated from the electrical side and the contacts are activated by a magnet, which means it is very safe even operating in 220V. Motorcycle horn relay is also a good idea but good luck with the complications with the voltage difference in your system. :)

@garryboi15 2 года назад

@@jongpenaranda just match the voltage of your pump.. mine is in 12v so a motorcycle relay is perfect.. just turn ON the relay when the pump turns ON.. and your lamp will turn ON as well.. completely safe and economic.

@jongpenaranda 2 года назад

@@garryboi15 Oh i see, i agree on that design is indeed more practical. But it can only sanitise water when pump is running only, meaning the UV lamp needs to be relocated before the water tank and not after. You just need to drain and clean your tank regularly though to lower risk of microorganisms that might grow in the system overtime since you cant efficiently place your uv on the final stage before faucet.

@garryboi15 2 года назад

@@jongpenaranda you can place the UV lamp anywhere in the system, the pump is just the trigger. as long as you did not add more air in your reservior.. it should match the pressure switch that the pump is set to operate. it should turn on everytime you fetch water from the faucet.

@jongpenaranda Год назад

For those requesting for the product link, here it is: Flowswitch: Amazon US amzn.to/3QZwxWh Lazada PH c.lazada.com.ph/t/c.YKnGsK UV Lamp Filter Amazon amzn.to/3CSGAqi Lazada PH c.lazada.com.ph/t/c.YKq5wx

@MrW3iss 10 месяцев назад

Thanks, couldn't find anywhere!

@deeboyjin8151 Год назад

Good day sir, ur video was very informative, but would u have any insight regarding connecting a water pump to an automatic flow switch for a whole house for instant hot when the faucet is opened?

@jongpenaranda Год назад

Hi thanks. Technically you can apply this design with the flowswitch to your whole house (just connect to water heater outlet pipe and wire it to the pump) as long as you have enough water pressure to activate the flowswitch, if not then your pump wont start. If that's the case, I strongly suggest to use a pressure switch, it far more safe and efficient.

@mikey5713 Год назад

Hi, have you tried using a dc flow switch with relay? The one you use po is made of brass, which leaches lead to your water...

@jongpenaranda Год назад

No I haven't, I have to use this type of switch to match the voltage of my UV ballast. With this small valve and small content of lead (if there is?) it wont matter....but anyway, most suppliers have a standard they follow regarding health and safety to pass product.

@artificial_intelligence0423 6 месяцев назад

Good day po sir, may water refilling station po ako at nag DIY ako ng vendo ko.. Issue nga Lang po is laging nk andar ang UV. Umiinit po sia, pag nilagyan ko po ng flow switch, dina po b iinit ang UV ko kahit parating Naka on ung switch ng UV?Salamat po

@OldLadyGamersince1990 4 месяца назад

Does it shorten the lifespan of the bulb? Some folks said that turning on/off the bulb frequently shorten the lifespan of it. What is your experience about this? thanks!

@entropy11 Год назад

What model flow sensor is that? The first one I tried failed to turn off once activated, I think the system pressure was too high.

@jongpenaranda Год назад

This model is a generic type so no specific brand. Try buying a sensor which has an adjustable sensitivity like on my video.

@pauladrianmarquita8854 5 месяцев назад

Hi. Is it okay to use this flowswitch to 25Watts bulb? I saw the specs of the flow switch and it says 100watts. Thank you

@jongpenaranda 4 месяца назад

Yes, you can use bulbs as long as it is below 100 watts.

@wonderboykun 11 месяцев назад

Does it need to be series or parallel connection for the power is also ok?

@jongpenaranda 11 месяцев назад

The power should be in series connection with the main cable.

@wonderboykun 11 месяцев назад

@@jongpenaranda ok thanks!

@jeffreyarroyo3390 Год назад

where i can buy

@jongpenaranda Год назад

You buy it online at Lazada. www.lazada.com.ph/products/ht-200-g12-g12-thread-220v-water-pump-flow-sensor-automatic-control-switch-i1127792144-s3911822482.html

@MsAlejandro2711 10 месяцев назад

hola hice todo lo mismo que tu y se me queda el sensor activado

@jongpenaranda 10 месяцев назад

Hi, please adjust the sensitivity of the sensor and make sure that it is installed horizontally. If still activated, maybe it is deffective. To confirm function, move flap of flow switch with screw driver while electrical circuit is connected or use multimeter.

@jongpenaranda 10 месяцев назад

And lastly, make sure you reached the minimum line pressure of your flow switch. About 60 to 70 psi.

@reinfrooze Год назад

sir penge ng link kung saan nyo nabili yan flow switch? yung nabili ko kasi di nagtagal.

@jongpenaranda Год назад

Not related to seller, but just sharing. Mine is 6 months old and still in good working condition. www.lazada.com.ph/products/ht-200-g12-g12-thread-220v-water-pump-flow-sensor-automatic-control-switch-i1127792144-s3911822482.html

@toposvlog 10 месяцев назад

Sir ilang psi or gaano kalakas ang waterflow para mapagana ang switch? may nabili kasi ako na ganyan hindi po nagswiswitch kahit sa faucet ko na nilagay. sana masagot salamat

@jongpenaranda 10 месяцев назад

About 60-80 psi water preasure needed to activate. If you dont have enough pressure, positioning the switch vertical with the flow will help, but will have a risk that it will stay activated. Also try adjusting the sensitivity.

@raffy3304 2 года назад

boss pwede ba tanggalin na lang yung tank? yung diretso na lang para di na magipon ng tubig. possible ba yun sa ganyan system

@jongpenaranda 2 года назад

Di pwede boss kasi mahina lang pressure ng pump installed. Double purpose kasi yung tank, it serves as storage and buffer/accumulator para magkapressure system mo. If you remove the tank, it will take you approx 1 to 2 minutes to fill-up a 300ml cup.

@raffy3304 2 года назад

boss isa pang question, anong brand ng water flow switch magandang bilhin? may mga nakita kasi ako sa shopee na pumutok agad.

@jongpenaranda 2 года назад

@@raffy3304 Hi sorry i missed your other question. Buy the magnetic type flowswitch same model on my video. It is safe even running in 220V since the electical and mechanical sides are totally isolated. Mine is working for 5 months straight up to now woth no issues.

@romeopronton9475 Месяц назад

same lng ba yan sa waterpure na brand..

@francescodimaria2124 Год назад

Ne ho comprato uno preciso su amazon ma non funziona, in pratica appena apro l'acqua si accende ma dopo mon si spegne piu

@jongpenaranda Год назад

Hi, idont really understand what you mean. But you need to adjust sensitivity of the flowswicth according to the pressure you have.

@artificial_intelligence0423 6 месяцев назад

Di po b malakas ang kain s kuryente pag laging Naka on ang UV?Salamat po

@jongpenaranda 4 месяца назад

it depends sa size ng uv lamp/s mo. Ok lang if 50-100 watts, pero i suggest for a flowswitch para di uminit masyado and maextend life ng UV lamp gas and coating. But if you have multiple UV lamps, then malakas yan sa kuryente.

@artificial_intelligence0423 Месяц назад

S water refilling station po, ano pong dapat n variation, 100w or 260w? S lazada kc may dalawang variations?

@godblessthelessfortunate3175 Год назад

Why do you need a UV filter if the RO filters everything out including viruses and bacteria?

@jongpenaranda Год назад

I added my UV filter as an extra precaution to get optimum removal of unwanted micro organisms. In addition, through time of use with your RO system, the efficiency drops and this may cause bacteria build up on the pressurized tank in which we cant clean regularly.

@nurdinharipin2206 2 месяца назад

@chesterdollente5781 2 года назад

Nag iinstal pb kau??pede makuwa mobile number nio

@jongpenaranda 2 года назад

Hi, sorry just DIY lang for the video. Installations are very easy to do, just follow the video step by step. Or I can answer some of your questions.

@chitoramos681 2 года назад

Boss, bakit tuloy-tuloy yung overflow ko?

@jongpenaranda 2 года назад

@@chitoramos681 Could you pls elaborate. Do you mean you've got continuous waste water flow? It should only be flowing while the pump is running only.