How to Install the Upgraded MTD Steering Rack Service Kit (753-11064B) 

BUY THE KIT HERE; amzn.to/3Y9oucJ

Let me start off by saying this is one of the best instructional videos I have ever watched. Fantastic job and many thanks for posting this! I am not very mechanical but, after watching your video, I was confident I could do it myself. After buying the repair kit and my first torque wrench on Amazon and writing down the instructions you gave, I was able to complete the job in less than two hours. I am so proud and grateful for the guidance and tips in your video. If anyone else is like me and needs a step-by-step list of the instructions, I am posting the one I made from your video. How to Install the upgraded MTD Steering Rack Service Kit (753-11064B) 1. Remove top plastic piece. 2. Push spring-loaded button and pull up on steering wheel. 3. Remove Phillips screw holding top plastic piece. 4. Rotate top plastic cover counter-clockwise to free tabs and lift up. Rotate it to the side and out of the way. 5. Remove black pushpin retainers from front and back of steering column. - Raise top center pin just enough to get under the whole retainer, the larger round part. 6. Lift lower plastic piece and rotate it to the side out of the way. Use tape to hold it out of the way. 7. Clean the top of the deck and notice the 2 carriage bolts. This is where the 2 nylon lock nuts will go. 8. Align the steering wheel (with spring-loaded button engaged) with wheels. Mark the steering column, the steering column bushing, and the frame with a marker. 9. Raise front of mower. 10. Use a ½” socket to remove center Nylock nut from end of the steering shaft. Discard. 11. Use needle nose pliers to remove cotter pins on the rear steering linkages from the steering spindle. Steering linkages should be hanging freely. 12. Use 7/16” socket to remove Nylock nuts on both sides of the steering rack, holding carriage bolts from the top, if necessary. 13. Remove steering support, steering rack and steering linkages. 14. Remove one of the remaining carriage bolts hanging down from the top so that, later, the steering rack assembly can be attached by the remaining bolt & rotated into place. 15. Slide off the pinion gear. 16. Align the new plastic rack support in the new support bracket by laying it down, sliding sideways, then twisting up, where it should hold in place. 17. Grease the inside channel of the rack support and the angle of the rack and slide it into the rack support, as well as the teeth on the steering rack. 18. Remove linkages from old steering support. The left one is silver and the right one is gold, looking from open side with plastic support to the rear. Transfer one at a time to new housing. 19. Align center line on steering rack with the center hole on the housing. 20. For future maintenance: Apply a little anti-seize lubricant to spline shaft where pinion gear goes. 21. Slide pinion gear onto steering shaft. 22. Mount rack assembly (open end at front) at an angle, with the remaining carriage bolt and connecting the teeth of the rack onto the pinion gear and lightly threading the new lock nut. 23. Double check that the steering wheel is centered before attaching remaining bolt. 24. Install other carriage bolt from the top and thread lock nut onto it. 25. Make sure the rack is centered. 26. Slowly tighten both 7/16” lock nuts, then torque to 90 inch pounds. 27. Tighten larger ½ “ lock nut to 185 inch pounds, with someone holding the steering wheel. 28. Insert tie rod ends into the hole on the steering spindle and install new bow-tie cotter pins. 29. Insure drive shaft is aligned. 30. Reinstall lower plastic cover and lock in place with push pin retainers. 31. Install upper plastic collar and rotate clockwise to lock in place. 32. Re-install Phillips screw into front of upper plastic cover. 33. Re adjust steering wheel into position with spring-loaded button.

Dude, I love precision, and this was precision! You should lecture at Harvard. Precise, concise and to the point. No razzle-dazzle, just the facts, ma'am. This guy gets to the point, and take it from there to the finish line. Quick and clear.

This is by far ...... one of the best DIY videos I have ever used. Two thumbs up!!!!

As usual, this young man rocks with perfect (9.9+++++++) presentation, analysis, intonation, to-the-point instruction, and clarity. For those of us who love all things mechanical, we salute you Sir. Well done. (From Florida, USA).

*MTD has once again updated this service kit, please read the following* At the time of filming this video (Jan 2022) the 753-11064B was the latest upgrade kit (it was published Aug 9th 2021) with the white Teflon plastic piece. However, as of March 2022 (2 months after filming this video) MTD has now issued a new service kit # 753-11064C with black plastic being used once again. If you want the latest upgrade service kit, I would recommend you use 753-11064C. The link below will show you the latest service kit info; cdn.datamanager.arinet.com/file/mtd/2ecc33cd-3fbd-4990-a5db-49e5da9edbb4

First of all CONGRATULATIONS on hitting the 50k half way mark to the Platinum RU-vid plaque. Secondly i must commend you on the thumbnail just a great idea including the 3 colours used on the different models that are sold you have a great thought process when putting together your videos. Third and most importantly even though most of your videos are well done with great audio and video angles with easy to follow instructions and explanation, personally i think this may be your best one yet. Everything looked so smooth i would think an 8 year old with tools could follow this video and get the job done. Fourth and final cannot wait to see the giveaway video and what you come up with. Thanks again the OLD MAN over and out!

I used this kit on my Troy BILT TB 30R. Man what a difference! Super easy to install.

Great instructional video. I just replaced the steering kit on my CC-30H which had started acting up last year and was quickly deteriorating. The hardest part was removing the old cotter pins on the rear steering linkages. They were a little inaccessible and I had to loosen the yellow fender shrouds to get hold of them with the BIG pliers. Took me about two hours (and I took a break).

Thanks for this info, I was wondering what the hell was going on with my steering.

I came across your video a few months back, we have a 2020 cc30h and sure enough the steering started acting up last week, I watched your video again, ordered a kit from Amazon that had the exact same parts, replacement was fine except for the bow tie pin on the right side kept popping out so I just reused the pin,what a difference, no more sloppy steering 👍thank you for your video’s, saved me $$$$ from having to take it to a shop

Make sure your front tires are properly inflated as this caused strain on the steering components. Always inspect the bushing where the shaft comes through the floor.👍

This is awesome. Facing the same situation

I told my sister it happened because she didn’t have both hands on the wheel, lololo I watched her mow and she showed me both hands on the steering wheel, lololo ❤

Did mine last week,cut my grass this week worked fine thank you for the video

Just did the surgery...with success, thanks to you Eliminator! You are so right about those farging *#! circlips....(Get the tool...save 30+mins.) Best regards,

I Love DETAIL videos like this, thank you so much Brother!!!!

Thank you for the video and thank you MTD for modifying the steering. I have replaced 5 of these on the same more and I think I finally replaced my last one. I was struggling with the new insert until I found this video. Thanks again.

The Craftsman rear-engine Riders are the exact same issue thank you for your detailed very understanding video

This is a outstanding video on the steering issue thanks

Thanks, you put out a clear instruction video making me confident I can do the work myself.

Thanks!!! Excellent video...just did the repair. Videos like this help save us thousands over a lifetime. Hardest part is getting out those pins..took me awhile to get the first one out..basically just destroyed it .. also a little tricky to get the part back on..

I'm in Australia and I own a Rover Mini Rider Hydro, also made by MTD. Exact same rack, same issue. I've replaced 3x racks myself in the last 12 months, each time I called MTD they were out of racks and said there was no problem with the design. I had to order replacements from Amazon overseas and they'd last for about 3 months before they'd fail again. So glad they've finally released an upgrade! MTD Australia can't tell me when they're getting stock of the kits, but I've just replaced the rack AGAIN so to make it last until I can get the upgrade kit, I've put a zip tie above the rack in the black plastic guide to stop it from backing out (different to where your customer had theirs, behind & above the rack). See how she goes! Thanks for the vid.

This works for a murray 24 in riding mowing. Same equipment only difference is the color. Murray is red.

Congrats on reaching 50k. You are doing a great job on this channel!!

No grease fittings except on the wheels. I used spray lithium and lubed the steering shaft, the spindles (king pins) and the gear plate. Mine was ok, just hard to steer and squealing. Aired up the tires and now it steers great.

It's too bad Part's stores are still selling the old gear and slide, they should be helping people out and tell them it's been updated, this fix is great and works great

Congratulations on reaching this milestone and thanks for another well rounded tutorial.

Just to thank you for the great tutorial. I did it myself with your help. Really appreciate it!🙏👍

Great Vid Elinator! Thank you

That was an awesome in-depth on the repair. Of course, I found this AFTER I had to do mine. Lol But the repair kits make a huge difference. You covered every step perfectly. 👉👍

One thing I would like to add for this install . You will find the job a lot easier if you remove the front tires so you can easily access the cotter pins. For the removal of the old and install of the new.

Super job! Thanks for the info.

Great detailed repair video!! :)

Great video Eliminator Performance video footage is really clear,You explain the job really well , Congratulations on hitting the 50k subscribers well deserved.

Hi I just replaced the rack and gear on my TB30 after watching some of the YT videos on this subject, I got the kit from amazon and it was okay, however a simple file test on the old OEM one and the new one showed that the amzn one is not hardened at all so I don't think it will last to long. The stock one lasted 6 years. I think next year after the season i am going to pull it apart again check the wear and also see if it is high carbon and can be heat treated, then I will go ahead and harden it and put it back. Yeah the one from MTD was $67. US so it was pretty expensive.

Thank you for this video! Very well explained, really helped installing the new kit ... cheers!!

I have watched three other videos on fixing this exact problem on these mowers, and no one ever removed the top plastics or marked the steering shaft. All that is unnecessary. But if you pushed up one of the two bolts for the bracket, or just want to clean in there, then yeah. If you are careful, you won't push either of the bolts up. To keep junk out of the new steering assembly, I'd put some Gorilla tape on the front and rear of the bracket.

I like especially the secure bolt on the chain hoist

Very well done! Thanks!

Congrats on 50k. As always, good clear instructions on repair. Stay Safe. Rick

Great video, part changed successfully.

Thanks great video and extremely informative will be doing this on mine soon

Doing Lords work. Costed me 32$ and an hour to fix this compared to 150$ and a 3 day wait at the repair shop.

Wicked job at hitting 50K!

I uses cub cadets parts to fix steering on my murray riding mower

Congratulations on 50k a great achievement there brother. And good how-to video on this mtd steering issue.

Thank you for this.!

MTD is not the only one with this exact same issue. The rear engine riders made by husqvarna, like the weed eater one, have the exact same issue.

Awesome job as usual, good explanation of work.

I wish they'd use a bushing in the bracket for the pinion shaft.

Nice easy to follow video Jake, congrats on the 50k, you're doing great bud!!! 👍 That was nice of your Old Man to hold the steering wheel for you while you tightened the steering nut. Maybe one day he'll do a video with you and actually get in the video. 🤣🙂

Awesome fix thanks.

Congrats on reaching 50,000 subscribers Jake! Well deserved for your channel. Nice repair on the Cub Cadet rack. 👍🇨🇦🇺🇸Roger

Good ideal on chain hoist bolt but I’ve never done it, but I don’t have any china hoist eather

nice set up EP. ANOTHER WELL EXPLAINED VIDEO! THANK YOU

You da man! Thanks

Excellent video. Q: do you have a video on how to replace the actual steering shaft itself? Thanks.

Good stuff!

Excellent video!

Helpful vid but I wish it showed how to remove the pinion gear so I could put the new one on from the kit. As it was, I had to leave the old one on. Fortunately, it was not the issue…it was the bad teeth on the bar. Steers like a Crown Vic now!

I’m thinking this might work on my R 110 craftsman? I bought my little craftsman about three years ago

what if the linkages are twisted? i got them out.. but now i cant get them back in!? Ugh.. lol its too hot outside today to get frustrated by this! hellllp!!!

Congratulations 🎊 👏 💐 great video

Can the steering bar be replaced leaving the tires on and working from underneath the front with 2 drive on ramps

Great video. My mower cuts terrible. One side cuts higher than the other. Terracing I believe it's called. MTD says can't be fixed. Only front to back. Any suggestions?

Great video. Tons of confusion on proper kit item#. Cub website shows for 753-11064B shows a black rack support while 753-11064C shows a white one. the C part isn’t showing anywhere. My dealers said the black is current updated one and what will come in the 753-11064B they order for me. Who knows what I will actually get.

excellent video, very helpful

CONGRATS!

Great video keep up the good work

I’ve found out heavy people steering goes bad twice as fast as a 150 lb person, sadly it’s just what I’ve been seeing 😢

Can you lower the steering on the Troy bilt 30” mower. It’s a bit high for mowing.

8:12 Great informational video. My mower is having steering issues now as well. Any tips on how you got access to the cotter pin here? You mentioned the tool you used. But, I can barely see where the cotter pin is, let alone reach it. I have yet to run into a video that actually showed this step. It is very frustrating to know what needs to be done, but not being able to access it. Thank you.

My club cadet cc30 has a lot of play in steering wheel what can I do?

Great Video. I have the craftsman R110. Since you did not mention it, does that kit fit my craftsman as well?

Hello, i see there is a 753-11064C version . What is the difference between the 753-11064b vs 753-11064C

Can't get this part in Australia no one could get it I had to make my own steering set up

They Should Make The Plastic Piece Out Of Brass And Use Some Lube Once In Awhile. DUGH?

Can you tell me where you got the upgraded kit?? There are so many for sale, how do you know its the upgraded instead of the original ? GREAT video Thanks!!!

HELP , Can you tell me how to raise the RPMs on the mower. It seems a bit low and runs at 3200 RPMS full throttle with the PTO engaged. Seems like it needs higer RPMS to cut he grass easier. How do I adjust the throttle to gains more ROMS on the Cub cadet CC30H , the throttle plate looks identical to the one on your video. Thank

Hi, Do you know the individual Part number of the White Steering Rack Support. I would like to order a couple of spares since its a Plastic Part and will wear out. Thanks

Will the repair kit resolve imo excessive steering wheel play?

If you put the mower vertical that way are you draining the gas and oil first or is it sealed well enough that is not an issue?

Do you work on Scag Turf Tigers

👍great job

50k👍👍👌👌