HOW TO JIMNY [ Replacing the rear wheel bearing at home or in the bush ] **With ABS** 

Just found my leaky oils seal needs doing after replacing a good one after doing a diff swap so will do bearings while I'm at it, great tutorial mate! Nice and detailed yet simple and to the point.

Awesome video. About to remove my rear diff centre so a lot of this is necessary to do that as well. Now I’ve seen this video I will replace both rear bearings while the diff is at the shop. Thanks heaps from Moorooka, Brisbane Southside

Thanks for the video mate ! Very helpful. Regards from South Africa 🇿🇦

Best video av found to follow will be doing mine now 😂💪

Nice thorough video! On my non-abs model I make the cutting part easier by cutting through the bearing outer race first, which then allows me to slide the back plate off and out of the way before cutting the retainer. I don't think the backplate clears the tone ring on ABS models though? The inner race then normally hammers off.

Thank you for this epic guide, just finished doing this myself thanks to this video. Will just note that in my case the 32mm diameter tube didn't fit over the axle, so had to use punches but other than that appreciate all the info!

very good I learned one more… thank you very much, directly from Brazil 🤘😎

Brilliant, thanks a lot. Love the make shift slid-hammer! Is it possible to do the input shaft bearing in situ? Just purchased another Jimny and the rear axle growls gently all the time. Not sure if it is wheel or input shaft so may just do all three.

I'm wondering if you have Extended Diff Breathers. While they primarily prevent water getting into the diff housing, they also serve the purpose of preventing the factory diff breathers from failing. If the diff housing can't breath, the sudden cooling of a water crossing will cause it to try and suck in from the wheel bearings.

Well done !!!... saludos desde Perú . Quisiera saber tu expericiencia con esta camioneta . Has probado la la nueva Jimny?

Great video's I've subbed 👍👍. Any advice on reinstalling the half shaft? I was hoping you was going to do a video on the reassembly. What's the best way to put the shaft back in does it take much force to push the bearing back into place? If so what's the best way of doing it?

Nice video mate. It's not that easy job either. Jimnys are fun but pain to repair

good job

I have problem with my jimny. I hope you can give me ideas or advice on what to do. This is what happen. I parked my jimny and after a day i tried to use it. so start the engine, stepped on the brake put my AT gear to reverse and released the handbrake. It won't reverse. The other rear wheel is already spinning but the one on the rear right wheel wont turn. so I jack both rear tires and tried turning the right wheel. It feels like a locked steering wheel where it only turns half inch left and right. and when I tried to remove the tires. It so happen that one of the lug nut got busted so I used a nut removal tool and when I hammer it to the busted lug nut the wheel suddenly turn freely. So the hammering fixed my problem. But I want to know what might have caused this problem? what can I do about it? thank you so much for the videos it helps me a lot with my little jimny.

Are the parts the same for a1999 grand vitara.

спасибо братан!

Ótimo trabalho

Another really helpful video thank you 🙏. Any over social media to follow you on

Did you have to bleed the brakes after the install mate?

Hey, thanks for showing. What I don´t understand is, why the bearing has a gearwheel? What is that for?

do you have any tips for EGR valve cleaning on the jimny? do you need to remove it or is it enough to spray a cleaner into the air intake?

Ah, now I see, the bearing sits on the axle and is not pressed into the diff housing, that´s great.

Do you think it would be worth using a good quality waterproof grease when refitting to try and help keep the shit out?

Boy I wish my wheel bearings came off as nicely as yours. Shitest job I've done on my car

Витаю. Україна.