DIY Pure Sine Wave Inverter 12V To 220V - 1000W [Full Video] ✓ 

Thanks

30-40khz

Thanks 😊

I will try my best

Hello, The circuit diagrams of all sections are in video ,

Thank you for supporting 😊

Hi Friend, All Schematics are already in video, thanks For watching

Hello, The circuit diagram is all parts in video

Is it pure sine wave output? And have you measured it in AC ?

It ok now the 2.2uf 400vols is open thats why it cant filter the output.thank you for your reply more power to your chanel..

Nice to hear that it worked Have a nice day :-)

But have a probleme the mosfet getting hot even no load.

​@@eduardobautista9557send me an email with the circuit diagram so I will send you mine

There is voltage adjustment potentiometer to set the voltage to 300V

@@Electronic_For_You Thank you for your answer. I noticed when you put some load @22:47, voltage increased from 220v to 230v. I am having the same problem in a lab power supply that i am building and don't know why this overshooting is happening. I suspect OP AMP gain but have no expertise on this. Do you have please some advise ? Thanks.

I don't think it will cause any problems, because 230V-240V is normal ,

HighVoltage side MOSFETs VS1 and VS2 were at the wrong point! Later I fixed it ! I think it's better to use 12V Isolated Auxiliary Voltage from Transformer

It's all shown in video

Ok, I will try 😊

There are all schematics shown in video

Please, is there any other means of payment apart from debit and credit cards?

Payment for what?

Use 7812 & 7805 regulator

@@Electronic_For_You how to convt 200+ VDC to less 30VDC for voltage regulators

@@Electronic_For_You HF chopper output is 220vdc or plus.. You are input it to sinewave pcb.but egs002 module need 30 or under dc voltage.. How to get suply for it. ?

Use extra 4 turns for module supply

40khz (EE-35)

@@Electronic_For_You thanks bro. Nice work

@@Electronic_For_You 100khz par kya problem h bro. Ye same core size 2000 watt nikal degi.

Current consumption increases

@@Electronic_For_You i mean aap ne two tranformer use kiye single transformer use kar lete frequncy 100khz kar lete 1000 watt output mil jata. If Frequncy increse core size decrese

It's same

You even watched the video?

@@Electronic_For_You yeah..but how to calculate? Why 45 turn? Based on why?

Based on core EE-35

Thanks ❤️

The 3rd diagram isn't clear...

Here is a PDF , I recommend Using Isolated Power supply for supplying the module! pdf1.alldatasheet.com/datasheet-pdf/view/1132081/EGMICRO/EGS002.html

@@Electronic_For_You fantastic 😻 thank u sir

You are welcome 😊

Sorry, But I don't sell products, Thanks for watching 👍

How much price

Please tell me

Power supply

This is for educational purposes, I don't sell products ✌️

I'm already working on a PCB Project :-)

@@Electronic_For_You Nice! Will look forward

All diagrams I showed in video 😊 Thanks for watching

Hello, I can see you have set the current limit of your lab power supply to 1Amps , and voltage drops to 7v this is why your Inverter is resetting!

@@Electronic_For_You thanks u sir

You are welcome

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HhRgXBVkSgs.htmlsi=pUVAIUO6LJrIWhSl

I think it's because of thin tracks of MOSFETs that burned out early at high current, this is why I used copper stripes to carry high current! And you should always use a fuse at input to protect yourself from exploding components 😆

You should use car headlight bulb to test the no-load current consumption. If the bulb light up when no load added and MOSFET get too hot, your circuit may have some mistake like transfomer fail, driver signal from IC not corret or you have bad MOSFET😊

You are right! It's a very good technique

Can you tell me in English?

The transformer is key to success, and it's the most difficult part of this project

I don't have 1000W Power source

Relaly me kitana load mil sakta hai bro.?

700W continuous (1000W Peak) If everything is built right

Using buck converter or voltage regulators