How to Make 2KW induction heater from old induction cooker Great idea DIY induction heater 

It's amazing content sir.. Watching here sending full support thank you for sharing this

This project is very good!

a great project, you are very good, the kitchen has many uses

Thanks for this great video, I know it's been a long time coming! But I like some tips. I want to know if copper coils can be put on each burner together in 4 induction burners. Then connect them together to take advantage of the full capacity of the stove, which is 6 kW, to get more energy. Thanks from Egypt

Genial.... Es exactamente lo que quiero hacer..... Será para calentar un cautín tipo hacha para soldar canaletas galvanizadas... Gracias

In your opinion, what is the insulating material above the coil if you want to use this method, and what is the amount of heat generated by this process?

Я знав що теоретично це можна зробити, але не маючи потрібних знань шукав підтвердження в українському сегменті ютубу. Знайшов але не так детально (були питання по котушці), тепер дякуючи Вашому ролику я реалізую свій проект. Спасибі🙏.

Great video, but I was wondering if there is a specific configuration for winding the coil or i can wind it however I want.

For Cooper?

Oh, i see: if it's still able to drive pancake workcoils in the kitchen then why not an air-core selenoïd?! Well, a genuine IH cooking base happens to be featured with flux-concentrator yokes located below its glass surface, inside in close proximity to the Litz wire actually, so we don't see it but it's there for a purpose nonetheless. ... As a matter of fact i must confess i thought of a similar procedure when i acquired my Salton iD-1081 and found out such pancake workcoils impose a disc diameter of nearly 4+ inches for its detection to succeed. The exact date was December 21st, 2010... Lets raise the bar over a decade later please! Air-core selenoïds generate only TWO poles with just one single magnetic vector in between. My challenge is to "Flex the flux" so to bend that vector in a way to multiply the poles, to redistribute the magnetic energy more evenly rather than focus as a red spot. The thing is all applications don't necessarily even require a metal to be glowing-red, 183°C ~ 188°C (as for 60/40 Solder Alloy) would have been fine back then, though an air-core selenoïd spits out radio noise that has to be tamed down, euh... M'well, unless living in a forest with no neighbours (and no wall-plugs), possibly relying on batteries or solar panels... Consider by folding magnetic vectors via "U" shaped flux-concentrating cores it should become easy & convenient to shield it all in a Faraday box, with the workload sealing its IH Aperture electrically as needed. No more EMi! Believe me, it's sort of boring when the neighbour starts paying visits everytime one installs in the veranda to relax and finally flip the switch, euh... Try it around an A.M. radio, it's like a "barker" invitation signal! At 2 KW why not add an antenna to communicate with beings in space, or on the moon? ... Good day, have fun!!

Try taking the secondary coil out of a microwave oven transformer and set it on an induction stovetop with the two ends of the coil about 4 or 5 inches apart then turn the thing on but step back.. lol.. if it grabs you than you shouldnt die but you will at least wake up a little while later.. the more powerful the induction cooktop is the more the coil will multiply the induced voltage across itself.. i tried it on a 6kw and it made the coil arc to the stove and killed the main breaker to the house.. 150 amp breaker.. stove fried its brains..

can you explain to me something how come these wires have no insulation for the coil ?

Working perfectly, but its blown the sparks and coil got damaged. How to prevent this damage.

Hello , I bought this card but I will wrap my coil myself. do you know the uh value of the coil?

I guess as its winding it will get short circuit so coil gets spark and damage

Can you make a video how to make working without a iron plate please 🙏.

Too bad i have the coil, but the control board was damaged beyond repair. Ou well guess i need to learn how to make control board then.

E0 error only showing how to stop E0 error and make heating?

Danger! The coil is DC high voltage, DIY is not encouraged.