How to make a beaded necklace. Easy beading tutorial. Last minute DIY NECKLACE 

Would love to see your designs!

Praise p

Hi judith...what picture...what is your FB I can send it to your FB address

Thanks .Nice mala

1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111¹111111111111111111111111111111111111111111111111111¹1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111¹11¹111111111111111111111111111111111¹¹¹11111¹111¹11111111111111111111111111111111111111¹1111¹111111111111111111111111111111111¹1¹1111111111111¹1¹11111111¹1111¹¹¹¹¹¹¹¹¹¹¹¹¹¹111111¹111111111¹¹111¹11¹¹¹¹¹1¹¹¹

класно

You’re welcome 😊

i never measure the thread. Im working with regular sewing thread (not wire).

Hi Sweetheart, I hope that I can help you... I cut 6 metres/yards off my spool of 'Nymo D' thread, which would obviously be ridiculously too long to work with if I tried to start at one end and get to the other! So I almost always slide my first 'unit' of beads to the middle of the the 6m/y thread (with a stopper bead FIRST) and begin weaving from the middle of the necklace, as I then only have 3 metres/yards of thread to work with which is much easier than having to finish and start new thread. When I get to the end of my piece I weave my clasp into a circle or drop shape (so I don't need to use jump rings to attach it later and reinforce it several times), then I turn the whole piece around and weave the other side of the piece from the middle again (but remember to remove the stop bead!), and then I do the same thing with the other end of the clasp. I usually have a good bit of thread left to weave back in to each end rather than just tying a knot and cutting at my 'clasp circles' - and then there's often some left over - but better too long than too short. I do the same with bracelets and any pieces where a lot of thread is needed. I hope I've been clear enough and it makes sense. Good luck with your project! PS: Nymo D Is a specialised beading thread and should be available at any good beading store or on Ebay. It comes in a wide range of colours but I've found that I mostly use 'Smoke' because it disappears into the beadwork but if I'm doing a black or white piece then I use black or white accordingly. BUT.. I heard that when doing multiple passes through the same beads you must be careful not to pierce the previous thread/s, but I've never had any problems with that. It's my go-to thread for everything, and comes in little bobbin size rolls (of 64 metres/yardsl and in very large spools. I keep a range of colours in the the bobbin sizes, and buy Smoke, Black, and White in the huge spools.. I think they're 1000 metres and last for YEARS - and I do a LOT of bead-weaving! Best wishes.

avec pleasure !

Thanks 🤗

thank you

thank you Khan!

Thank you

Thank you my friend

aliexpress.com pr pandahall.com

wildfire

ဪဇာသိး

မမ

wildfire 0.15 mm , or ... maybe nylon thread will be ok

i used regular sewing thread...(doubled it !!!)

+Denise Winant use beading wire

Then the wire shows. Wire is metal. I will try fishing line again. That is invisible but with 2 needles it is difficult to work with. It curls. I'll try my plastic pliers and try to straighten it out.

это не имеет значения, как долго это нить ... вы можете сделать узел, который он не увидит

hi...this is a necklace. pls watch the tutorial ..I dont know how much thread do you need, I always add more thread by making a knot because it wont be seen -it will get hidden through the beads, I dont like to work with long thread.

Thank you I did go back feel a little silly I love the knecklace apologies

Like

Thanks 🤗

wildfire, nylon, fireline, cotton thread

Thankyou

For this tutorial how am I supposed to add thread if the thread is almost at then end?

length=15.5 inch (40 CM)-without clasps 46 pearl beads (6mm) 56 gold beads (4mm) 28 bicone beads (4mm)-black 29 pearl beads (4mm) If you have any question please feel free and ask !!!

شكرا جزيلا

nymo...or regular sewing thread or any other beading thread

it doesnt matter the length of the thread . you can add more thread by making a knot , it will get hidden through the beads and you wont see it !

have you tried using silver beads in place of gold beads? I'm real excited about this choker. It's so pretty

no but i can try making it with silver beads

Score Der @

@@beadingtutorials ' s

Ok, thank you

thx Rachel . LOVE!

thank you