How to mirror the Team Garage Hack forward motor mount to allow for proper drive shaft alignment when running Axial AR45 axles. gspeedchassis.com/products/tg...
Just a tip to others, to prevent the drill bit from running, bolt up the triangle piece with both fasteners. Take your bit and drill through the hole in the guide to make your hole in the frame rails. Unbolt it and do the same to the other side.
Ok Mr. Gspd I’m a believer of all tha hype bro trx4 v3x4 zr2 just pulled a krazy insane vertical Rez line man 🤯🤓 stay safe man!! One last thing hell of a chassis and Rez approved man✊🏽✊🏽🤓.. Good info on vid too bro..
No. The shock hoop brackets is what needs to be drilled on the V1-C1 and they come with the transmission, not the chassis so holes will still need to be drilled in the future
V1-C1 package deal gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/gspeed-chassis-v1-c1-package-deal Square chassis spacers gspeedchassis.com/collections/tgh-v3-products/products/gspeed-chassis-square-spacers . GSPEED G-LD servo mount gspeedchassis.com/products/gspeed-chassis-g-ld-laydown-cms-servo-mount . Hard body mount sliders for the RC4WD Mojave ii hard body 2 door gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/gspeed-chassis-v1-c1-hard-body-mount-sliders . Forward motor mount and 30% overdrive transfer case gspeedchassis.com/collections/tgh-v3-products/products/tgh-forward-motor-mount-for-v3-chassis-and-30-overdrive-creeper-t-package . I'm running the TGH-FMM forward motor mount and transfer case with AR45 axles. You'll need the TGH mirror drilling jig kit to assist in laying out new holes to drill in the front shock hoop brackets in order to mount a mirrored front motor mount. gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/tgh-mirrored-drilling-jig-forward-motor-mount-kit Instructional video on mirroring the front motor mount ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hqGZ6ldiAJo.html Instructional video on mirroring the Creeper T transfer case ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WHppEWlDsEE.html . Suspension link kits can be purchased here. There are drop down menus to select the parts you are building with, like AR45 axles and G-MP panhard mount. hardcore-rc.ecwid.com/G-Speed-V1-C1-AR45-Portal-Kit-p367791960 . Wheel base- 11.75" Front and rear drive shafts- 105mm Center drive shaft- 70mm You can use drive shafts like..... supershafty.com/products/supershafty-mip-hd-driveline-individual-parts_pos=1&_sid=087864444&_ss=r&variant=12160250708062 Or www.amainhobbies.com/axial-wb8hd-driveshaft-set-2-axi31133/p-qtqqtqtqymzxactz . 3Brothers RC 👇👇👇 www.3brothersrc.com/product-page/anti-foams-4-19-1-pair G14 servo gspeedchassis.com/products/g14-direct-power-servo?_pos=1&_sid=76baf2e7a&_ss=r 3Brothers RC 2750kv motor gspeedchassis.com/products/kratos-ten-2750kv-10-pole-sensored-brushless-motor?_pos=1&_sid=db51ae6a0&_ss=r Recommend Team KNK hardware 3mm screws, nuts and washers gspeedchassis.com/collections/team-knk-hardware/products/team-knk-hardware-700-pcs-monster-bag-stainless-hardware-kit Assorted spacers gspeedchassis.com/collections/team-knk-hardware/products/team-knk-hardware-aluminum-spacer-variety-pack-natural
If the TGH forward motor mount was purchased from the GSPEED Chassis website, it comes with shock hoop brackets that don't need to be drilled if not mirroring the mount.