Тёмный

How to open and fix a broken switch or slider on the RadioMaster TX16S or Eachine TX16S 

i3Drones & iTech for life
Подписаться 1,4 тыс.
Просмотров 1,1 тыс.
50% 1

The video presents all the steps required to open/close the case of the TX16S transmitter and replace a damaged switch or slider. All the proposed steps in this video can be applied to the RadioMaster TX16S or Eachine TX16S.
00:00 - Introduction
00:47 - Opening the RadioMaster TX16S or Eachine TX16S
01:53 - Replacing the side sliders
02:08 - Replacing the SF & SE or SH & SG switches
03:02 - Replacing the SA & SB or SC & SD switches
03:21 - Closing the RadioMaster TX16S or Eachine TX16S
Eachine TX16S Multi-protocol Radio Transmitter: bit.ly/3k4ennI
Switches:
---------------
SA & SB: www.banggood.com/Original-Rad...
SC & SD: www.banggood.com/Original-Rad...
SF & SE: www.banggood.com/Original-Rad...
SH & SG: www.banggood.com/Original-Rad...
Side Sliders
----------------------
www.banggood.com/Original-Rad...
Switch’s nut disassembling tool
---------------------------------------------------
www.banggood.com/8PCS-STAR-PO...
╔═╦╗╔╦╗╔═╦═╦╦╦╦╗╔═╗
║╚╣║║║╚╣╚╣╔╣╔╣║╚╣═╣ → bit.ly/3arWvOq
╠╗║╚╝║║╠╗║╚╣║║║║║═╣ I Really Appreciate Your Support!
╚═╩══╩═╩═╩═╩╝╚╩═╩═╝

Наука

Опубликовано:

 

7 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 6   
@jeanlucvassort6411
@jeanlucvassort6411 Год назад
an other very good and instructive video - Thanks a lot
@i3Drones
@i3Drones Год назад
In short time (around 1 week) another video will come. So, be tune.
@jeanlucvassort6411
@jeanlucvassort6411 Год назад
@@i3Drones fine :-) thanks ...
@visualdosage234
@visualdosage234 2 года назад
Hi i just got this radio, and when callibrating and sliding the right slider all the way to the top on screen i only see it going a bit above half of the center, the left slider reaches the top. Do u know a fix and if its software or hardware? When sliding it smoothly goes from the bottom till lets say 54% without a dead zone so i think its a bug or setting, anyone got a clue?
@i3Drones
@i3Drones 2 года назад
To be sure that iti is not a software problem go to a "factory reset". In this mode the default settings will be set and you can now chech if it is working correctly. If work OK, this means trat from the settings the output values were limited in a way.
@visualdosage234
@visualdosage234 2 года назад
@@i3Drones noo i fixed it haha i just didnt center that stick before callibration when it asked me to, thanks for the reply!
Далее
Radiomaster TX16S Teardown and Jumper T16 comparison
13:55
Все сезоны бравл пассов…!!!😨
00:59
The Clever Way to Count Tanks - Numberphile
16:45
Просмотров 792 тыс.
Why The Windows Phone Failed
24:08
Просмотров 309 тыс.
OpenTX Part 5: How to use Logical Switches
19:09
Просмотров 6 тыс.
5 ways to setup models in OpenTX - TX16S
11:33
Просмотров 26 тыс.
Your USB-C Cable probably SUCKS! Sooo is that Bad?
10:54
Новые iPhone 16 и 16 Pro Max
0:42
Просмотров 2,4 млн
Самая редкая видеокарта NVIDIA
1:00