Тёмный

How to pick the best air pressures for adventure/dual sport riding︱Cross Training Adventure 

Cross Training Adventure
Подписаться 66 тыс.
Просмотров 30 тыс.
50% 1

crosstrainingenduro.com tractionerag.com What are the best tyre pressures for dual sport and adventure bikes? There is a lot of debate about this, especially on the best air pressure for road and dirt road. Lets look at three options. First, you can just use the air pressures that are common with three broad groups of bikes. Twin cylinder adventure bikes. These typically weigh between 200 to 270kg. Adventure bike tyre pressures will vary between 30 and 40psi for road and dirt roads. Your larger single cylinder bikes weigh between 160 to 200kg. Air pressures will usually vary from 20 to 30psi. And finally you have the smaller single cylinder bikes, weighing from 125kg to 160kg. Their air pressures run mostly between 20 and 25psi. These are just very broad guidelines for dual sport tyre pressures. A second option to pick the best tyre pressure is to run with the manufacturer's recommendation. At the very least they will give an air pressure for road riding which is usually quite accurate. Remember to check the maximum pressures shown on the side of your tyres for Adventure bike tyre pressures. Usually there will be no conflict. Sometimes the motorbike manufacturer give you a figure for the best tyre pressure for dual sport riding. If they don't, you need to work out the best off road pressure yourself. And that leads to the third method, working it yourself. Deciding to work out the best tyre pressure can be a tricky business. We suggest using the manufacturer's recommendation as a baseline for dual sport tyre pressures and go from there. Try increasing or decreasing pressure in 5psi increments. When you feel you are getting close, try some fine tuning. Why go to all the hassle of working it out for yourself? There are lots of variables to the best tyre pressure for adventure riding. Your bikes' weight. Your weight. A pillion passenger. Any luggage to consider ofr Adventure bike tyre pressures? The profile, sidewall, and rubber compound of your tyres. How fast or aggressively do you ride? What sort of terrain? Do you have cast or spoked wheels? How hot is the climate? How hot is the ground? Is it worth experimenting to work your own custom dual sport tyre pressures? We will leave that up to you. Why is air pressure important? Once you are off road, traction becomes critical. You get a bigger contact patch on the ground as you lower the air pressure. But if the pressure is too low you can cause problems. Increased wear. Strange wear patterns if not using the best tyre pressure for adventure riding. Higher tyre temperature. Cracking of the rubber. Dented or cracked rims. Increased chance of punctures. Poor handling. You might unseat a tubeless tyre and lose all your pressure. And with tubes your tyre might move on the rim and rip the valve stem out of the tube. And of course too much adventure bike tyre pressure isn't good either. How long can you go? There are situations you may want to run very low pressures to avoid trouble. Very soft sand. Slippery mud. A steep climb. We have reports of adventure riders, on big heavy twins, temporarily running as low as 12psi just to get traction in difficult spots. Then they immediately pump the tyres up again. For single cylinder dual sport tyre pressures, you could probably run as low at 6psi just for tricky situations. But if you use tubes, please ensure your bike has rim locks to avoid the tyre moving and ripping your valve stem out of the tube. If you don't have rim locks, 10psi is probably safer. Remember you greatly increase your chances of problems with very low pressures. It is just for difficult situations. Extra motorbike tyre pressure tips? Carry your own tyre gauge. Remember air pumps at service stations can be up to 20% inaccurate when aiming for the best tyre pressure for adventure riding. If you use tubes, don't tighten the nut on your valve stem. If your tyre moves, you can see the valve stem leaning and fix it before you rip the valve stem. Carry a pump with you to work out the best tyre pressure for dual sport riding. If weight is an issue, little pumps like this are tiny and weigh nothing. Consider using a tyre sealant along with adventure bike tyre pressure. This can plug up small punctures. If you run tubes, some say it reduces the chances of pinch punctures. If your bike has narrow rims in 18, 19 or 21 inch sizes, you can use the TUbliss system to effectively convert your wheels to TUbliss. You can run quite low air pressures safely and just plug punctures in around two minutes. Do you have any further for dual sport tyre pressure tips? Interesting experiences? Let me know in the comments. I hope this vid is useful. If you are new to adventure riding, don't stress too much about getting your air pressures exact. Follow the manufacturer's guidelines for the best tyre pressure for dual sport riding and you can't go too far wrong. Safe riding!
#crosstrainingadventure #motorbiketirepressures #adventureriding

Спорт

Опубликовано:

 

9 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 181   
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Subscribe for weekly adventure & dual sport vids! English not your first language? Many subtitles... Safety & protective gear vids bit.ly/3BmKeGE Our dual sport & adv ride vids bit.ly/3HTdvvl Bike & product reviews bit.ly/3BrnVjq The more bizzare side! bit.ly/34ZschR The more philosophical side bit.ly/3v9nKYX Riding across Vietnam bit.ly/3pej9Rt DR650 project vids bit.ly/3gQEStP Check out our other channels too... Cross Training Enduro bit.ly/3Jncax4 Cross Training Trials bit.ly/3uUjwEm
@DamonStangherlin
@DamonStangherlin 2 года назад
Three main tips that come to mind are; -Have less psi on the front tire (1-2 psi less), for offroad riding you want more traction to the front than the rear. It's okay (FUN) if the rear steps out, less okay (BUTT PUCKER) if the front tire steps out. -Tip two is to find your baseline for offroad and road and keep it consistent for a while to learn how the bike/tires react to each and every situation. And then fluctuate if need be once comfortable. I recommend a year or so of doing a consistent X offroad psi and Y road psi. This also helps formulate personal opinions about certain tires (ie how they handle wet/dry/rock/sand etc) when you have a consistent baseline. -3; A little 12v pump with either a cig lighter or QD, works wonders for making you WANT to play around with psi or actually do pressure changes. Mine only costs about a 2 beer can space slot in the pack, and it takes me about 4 minutes to air up after riding at the end of some single track before riping back home. Coincidentally the same amount of time that it takes to shoot the shit with the riding buddies and or re-hydrate on h2o. For the first 4-6 or so years, I did not care anything about changing my tire pressure. And that's fine if you don't. But for the last while, I've been running different tire pressures for different scenarios and have found it has drastically improved my riding (probably due to being able to conquer more difficult hills/faster corners, thus improving my courage/confidence. On the klx with stock rims, no rim locks, and heavy-duty tubes. I've settled at 16 psi when I need it (ie slow tough enduro day), 18 for overall single track, 20-25 when I do dualsport shinanigans back and forth from dirt to paved, and 32 for road/hwy rip (1-2 psi less on the front for each). And I change when need be, but like mentioned in this video I settled on these based on the terrain I ride and all the other reasons mentioned. And his has kept me relatively flat-free, and dinged rim-free. Cheers on the excellent vid, very useful to the dual-sport/adv community🤙🏻
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Great top hear, Damon! Yes there are definitely benefits if you are willing to put the time in.
@mweskamppp
@mweskamppp Год назад
I have the 1200 GS and was driving long time with recommended max pressure since i am 130kg and was on travel with luggage. Much better driving after decreasing the pressure from 2.5 and 3 bars to 2.1 and 2.6 bars.
@DmitriyAdv
@DmitriyAdv 2 года назад
On lager/heavier bikes loaded with luggage and passengers, you're usually not far off from the max load of the tires. So, it's important to keep in mind that the max load of the tire is usually at max psi. Running too low with a heavy load will at best cause weird wear and at worst overheat and blowout, so as much as it sucks having to adjust tire pressures, it's better than sliding down the highway. I'm talking bikes that are in the 500lb range here, just to be clear. Which could easily be pushing 900lb with two people and gear.
@take5th
@take5th 2 года назад
I ride at 20R-24F psi. DRZ400. I go about 10 miles each way to trail, then ride on dirt until tired (not long! Can’t measure accurately due to excessive wheelies) , then 10 miles back home. I’ve had Shinko 700, Dunlop something or other (not trail wings), and pirelli scorpion pro. All last about 3000 miles. now have Tusk Dsports - love them - we’ll see how long they last. I ride sand primarily, and lower would certainly be better, but it’s a real bother for my short jaunts. The DSports have a solid carcass, and I weigh about 185 with gear. I like knowing that if I aired down a bit more traction would improve and that I am training at less traction, which I imagine doesn’t negatively affect technique. No rim locks.
@KLRmurdercycle
@KLRmurdercycle 2 года назад
20 in the rear and 24 in the front. I can't be bothered with airing up and down every time the surface changes. I just wanna ride.
@twowheelpilot
@twowheelpilot 2 года назад
I love Tubliss in the rear. Can't beat them. Haven't torn a valve out for years unlike before. I don't bother with front Tubliss. Never had a pinch flat on the front unlike the rear.
@SteelJM1
@SteelJM1 2 года назад
Agreed, and it seems like the rear likes to pick up nails/thorns whatever much more often than fronts. And its a huge PITA taking off a rear wheel and repairing/replacing a tube vs a front.
@allenhuling598
@allenhuling598 2 года назад
Great topic and very timely! On my T7 with the manufacture's tires, I've found that with the bike loaded and my weight at 110 kgs, dropping the pressures 6 psi from the recommended 36 rear and 32 front makes a world of difference for extended gravel and single track riding!!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Good to hear, Allen! Next time I see the owner of the T7 I rode I'll see what he finds works best.
@RedBaroness12
@RedBaroness12 2 года назад
i always appreciate your vids mate, keep the knowledge coming
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Will do, glad you are enjoying the vids. 👍😎
@CesarRamirez-cn5fw
@CesarRamirez-cn5fw 2 года назад
Glad you made this vid, I just bought a xr650l and went off roading with the 35 psi and it was a terrible experience.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I can imagine, Cesar! Does the manual give an offroad figure? Does the XR have rimlocks?
@dennisconrad6124
@dennisconrad6124 6 месяцев назад
Had a Yamaha XT225 and Kawasaki KLR 650. Once I lowered the pressure down to 18psi front, 14psi rear, I never went back. To me, it made a world of difference.
@crosstrainingadventure
@crosstrainingadventure 6 месяцев назад
😎👍
@CHUNKYNUGGET666
@CHUNKYNUGGET666 Месяц назад
Really gotta mention pressure gauge’s guys, they are pretty inaccurate across the board and most tend to become less accurate over time. Nearly all my gauges read different.. I carry a 60 psi Jaco gauge and a lil hand pump, I’m really enjoying playing with different pressures on the loops I do. It’s amazing the difference it makes! Also No digital no batteries a simple combo that just stays in the bag👍
@tincho1979
@tincho1979 3 месяца назад
Excelente video, interesante e instructivo. Yo utilizo Tubliss en mi Husky TE300 la delantera 14psi (menos solo sirva para pinchar) y 5psi en la traerá (tracciona magnifica mente y al tener mucho balón difícilmente pincha) Ahora estoy adentrándome en el mundo adventure y estoy experimentando, en principio tal como sugieres al final del video: utilizando las presiones recomendadas por el fabricante. Gracias y saludos desde Argentina 🇦🇷
@aaronroberts814
@aaronroberts814 2 года назад
I’ve always carried a small air pump, I haven’t needed it myself yet but I’ve lost count how many times I’ve met other riders out the bush with slow leaks/flat tyres that are happy to borrow it 👍
@crosstrainingadventure
@crosstrainingadventure 2 года назад
It's funny how many don't carry one, Aaron... even though they are tiny. My brother has his under the seat of his Beta RR300 and there's barely any room there at all, but it still fits.
@jimdavis1782
@jimdavis1782 2 года назад
Love the bike pump idea. Simpletech! Also the workout you'll get will build your strength so you can help lift your mates GS when it falls over.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
😂 I love simple cheap stuff!
@Dom-nt4gn
@Dom-nt4gn 2 года назад
Some interesting things I leaned from closed course road racing on racing slicks. When moving fast, tire pressure is a function of generating and maintaining proper heat in the tire. The higher the pressure the cooler the tire will run and thus the faster the rider will need to be to maintain proper cohesion with the ground. Race tires get so soft at operating temperatures that you can almost leave your thumbprint in them. I know this doesnt apply to dirt riding but it was pretty cool for me to see. Also doubling down on the tire pressure gauge, many many tire pressure gauges are very inaccurate, a lot of people trust their life with a tire pressure gauges that costs less than the cost of their lunch. Buy once, cry once and invest in an accurate one.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I looked briefly into road riding/racing pressures and it's a huge topic!
@Dowent
@Dowent 2 года назад
As long as you have tire warmers, dialing the pressure in on a track is no big deal. All the manufacturers will give you charts for their slicks and wets, what temp for which tire at which temperature. They give you the pressures at 80° for slicks and 40° for wets and since race is usually only after some practice rounds, if you start losing grip early, air down, if you start overheating (tire blue, inconsistent performance), air up.
@C0PED0GG
@C0PED0GG 2 года назад
Love the information you provide, Please keep up these videos!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Will do, Max! It's a lot of work doing these vids and the enduro channel as well but I'll see how long I can keep it going...
@allenhuling598
@allenhuling598 2 года назад
@@crosstrainingadventure Awesome, thanks Barry!
@vspatmx7458
@vspatmx7458 2 года назад
I would keep it at 5psi lower than recommended range. It improved ride contact patch grip and comfort, However.. Tyre flats increased dramatically
@yorkchris10
@yorkchris10 2 года назад
I stay at road pressure and accept the traction limits. I'd never had a flat with my radials on gravel highway until a track in Oz. The locals asked if I had good tires and I had more than 50% left on my good Michelin T66. They said I should adjust my air pressure because of sharp rocks, but I didn't and that was the only flat I' d had . I've seen 21" pinch flats on undeveloped highway at normal pressure.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I must admit I often just stay at road pressures nowadays too, Chris. If the ride only involves, say, 25% dirt roads I'll just skate around and enjoy the challenge of less traction.
@AussieDazza
@AussieDazza 2 года назад
You’re on the money, I run 24/25 psi on my 640 Adventure.
@fredman1085
@fredman1085 2 года назад
I'm new to dual sport and a couple of months ago I took my new Italian Princess Beta 390RRS up to visit my mom. Next day I went dirt biking and forgot to adjust my tire pressure back down and was dismayed how poor the traction was. After a little while I remembered about my road ride the day before and rode back to the truck to adjust the pressure back down and man what a difference. A stupid story I know but one learned first hand by me. I like 8 in back. And 11 up front. This works for my speed and varying terrain where I ride. When I where out my tires I'm going Tubliss but I'm too lazy to change just yet and my stock Michelins are surprisingly good.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Hopefully you'll enjoy TUbliss, our whole group is on them now. For our slow technical riding we only run about 3psi which is the equivalent of around 6psi... incredible grip! But poor handling at speed of course.
@wyattblessing7078
@wyattblessing7078 2 года назад
Don't feel bad, I had been riding trails for weeks, then left on a 3 day road ride with tires still at the dirt pressure. About half way into the trip my buddy noticed the low pressure but by then my tire was ruined. Weird wear patterns. I had to swap it out shortly after the ride.
@tsoc112
@tsoc112 2 года назад
Valve tool and bike pump are easy to carry. Get a high pressure pump and you'll be able to use it with your tubliss setup too. Mine constantly leaked so was handy in that respect too 😂
@Matt43
@Matt43 2 года назад
I find it worth it to experiment but only change pressures on the Adv bike if I am going to be off-road for long periods (1+ hours) before getting back on the pavement. Currently run sidewall pressure (34) on the road and 25-30 on the dirt for the 890 Adv R with Bridgestone AX41s. Love mousse inserts on the WR450, great traction... but more importantly, peace of mind!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Same here, Matt. I won't drop the pressures if I'm only on dirt for less than an hour. I don't mind the bike skating around a bit on gravel... adds to the challenge!
@MidCoastAdventures
@MidCoastAdventures 2 года назад
All good info there 😎👍 For me (DR650) 25 front and rear- tar, gravel roads, mud and beach sand. Too lazy to change, and adjust my riding to suit the surface.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Same here, I've been running around 25psi for my first 4000km simply because there's been a lot of road riding so far... when we get seriously offroad I'll go down to 18psi and have rimlocks fitted by then.
@pilotdane1
@pilotdane1 2 года назад
Barry - "THE MIGHTY SUZUKI DR 650" - On the road (as recommended) 21 front / 25 rear - Off road 1/2 way down - no bead locks - about 11 front / 13 rear ("ish") - But only if I'm gonna be off road for a wee bit. Never sheared a valve stem AND REALLY TAKES THE EDGE OF THE ROCKS / ROUGH STUFF - and obviously more traction. I have SLIME in my tubes & I also carry a SLIME COMPRESSOR with me - plugs into my BATTERY TENDER plug - quick & easy - just takes a couple of minutes.... If strictly off road & I'm putting the bike in the truck, I air them down before I leave as that ride will only see pavement for maybe a short period of time. LOVE YOUR WORK !!!!!!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Congrats on not ripping valve stems at those pressures without rim locks! I found that even at 15psi I was getting slippage of the tyre and those valve stems were leaning... mind you, I used to ride a lot more aggressively back in those days.
@davebennett5069
@davebennett5069 2 года назад
i stick it at 15psi in my crf 450L. works great for rocky / sandy trails, and it's tolerable on the road. since i barely ever ride on the road, it's just fine knowing that the lower air pressure is not ideal, but it means i don't have to get off any play the PSI game whenever I switch terrain. i make up for any discrepancies in the "ideal" pressure by just trying to ride better!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Enjoying the CRF Dave? I still haven't managed to get a ride on one but keen to see what they are like. Hopefully Honda will make a rally model!
@davebennett5069
@davebennett5069 2 года назад
@@crosstrainingadventure I really like the bike, however it is absolutely true that it's a real PAIN to ride until the ECU is replaced, due to the low rev fuel cutoff. So that's a barrier. But the handling is great, it's lightweight, and it has all the snot you need to get out of hairy situations or climb stuff. Plenty of snot for getting INTO trouble too... I probably wouldn't buy another one, but I have no motivation to replace it either.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Great to hear it's working for you overall. I've actually emailed Honda Australia to see if I can review a few models... but in my experience none of them ever respond.
@barrymurphy3554
@barrymurphy3554 2 года назад
Any other great video thanks Guys
@FriEnduro1
@FriEnduro1 2 года назад
Very good video
@souhailshamaissem7564
@souhailshamaissem7564 2 года назад
Excellent video
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Cheers Souhail
@Boonus18
@Boonus18 2 года назад
22.76 on the front, 25.67 in the rear. Unless it's a full moon, the I take the square root of those numbers, double it, then ad 15 psi.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Which hemisphere? Are you allowing for the Coriolis force? Any allowance for relativistic effects with your position in the gravity well?
@Boonus18
@Boonus18 2 года назад
@@crosstrainingadventure hmmmm, not really sure. I got those numbers from a forum post on Thumpertalk. The author was a 14 year old who has never ridden a motorcycle before, but he swears to be an expert, so I trust the information.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
In that case I will too!
@twowheelpilot
@twowheelpilot 2 года назад
What pressure do you suggest for a total eclipse?
@Boonus18
@Boonus18 2 года назад
@Wes B add 4.20%
@plve82
@plve82 2 года назад
I run 7psi in the front & rear of my dirt bike & On my road bike, 38 front & 42 rear.
@adventureguy4119
@adventureguy4119 Год назад
My shinko 705 front does not like below 35psi
@mimi1girl2dempsey3
@mimi1girl2dempsey3 2 года назад
After watching this I feel comfortable going 25psi front Mitas e-07 and 27psi rear Motos GPS. 20% asphalt, 80% dirt and trails. Versys-x 300. Recommended 28 and 32. I'm weary of pinching tubes on rocks when ripping through atv trails so would never go lower.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I'm not sure how much difference it makes, but you could always try some of that green Slime or a similar product in your tubes. With luck it will fix small punctures and might even reduce pinch punctures. Some riders put talc and even grease on the outside of the tube for this reason, although I'm not really sure how much this reduces pinch flats and if it's a great idea or not.
@tremorflow3614
@tremorflow3614 Год назад
Great video mate. Is that drone footage? Looks really trick hehe
@crosstrainingadventure
@crosstrainingadventure Год назад
Yep, I asked supporters if they'd like drone footage so there was some help to buy the Skydio autonomous drone... reviewed it on this channel. 😊
@mechcavandy986
@mechcavandy986 Год назад
I’m running 31 PSI on the rear and 29 PSI on the front of my BMW R 1200 GSA. I’m wondering if that’s too low on the front. I’m not off-road as much these days. I’m running tubeless Dunlop Trailmax Missions. If I were off road as much now, I know that would be fine.
@Dowent
@Dowent 2 года назад
Even on my light enduro bike, I always start the ride with high pressures (around 1.5atm ~ 22psi) and air down when I start to lose traction too much. I often even air down in a middle of a climb. It can be tricky to learn airing down with one hand while balancing the bike with other while not falling, since the hill was steep enough to stop me in my tracks, but it's easy get used to it. I only air up once I get very low (0.4-0.6atm ~6-9PSI) or when I'm about to do a longer road section. It takes under a minute to air down and under 5 minutes to air up (I have a stripped mini 12v compressor), so it's not a bother.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I remember once being stuck on a mild but muddy climb... it took a few goes before I finally realised the solution was go very low PSI just to get up and out. Then pump the rear up again. Very handy!
@theravedaddy
@theravedaddy 2 года назад
Thais only check their air pressures on a partial eclipse, hence every tyre has 75psi in it. This is checked by pressing your thumb into the tread.....it theres ANY sign of movement add 30psi until solid.
@mosca3289
@mosca3289 2 года назад
Same in Vietnam 👍🏻
@crosstrainingadventure
@crosstrainingadventure 2 года назад
That's what I call precision air pressure monitoring!
@thealvaco
@thealvaco 2 года назад
Good tip regarding the valve stem but. Been doing this for years, i recommend it.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I learned the hard way... two or three ripped stems over the years lol.
@thealvaco
@thealvaco 2 года назад
@@crosstrainingadventure yeah no patching that.
@ShadowsFirst
@ShadowsFirst 2 года назад
Tubliss is also great for keeping dirt out of the inside of your tires and bead seating areas. Especially at low pressure, this is a great way to get a flat on a conventional tube system. Get some dirt and or debris in there and I've had the friction (over time) cause abrasions in the tube that have left me sitting when I wanna be riding. Tubliss seals things up even at
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Our group loves TUbliss, pretty much zero issues over five years.
@usbsol
@usbsol 2 года назад
How is road riding on the tubliss system. I have a 250 l, so I am not doing insane speeds on road (or off road 😉). But Tubliss is like this will explode if you put it near tarmac 😄.... Will it? 😳
@ShadowsFirst
@ShadowsFirst 2 года назад
@@usbsol No it's fine on road. You just may want to adjust your tire pressure accordingly. The system itself won't be any issue.
@sidickkoodoruth6529
@sidickkoodoruth6529 2 года назад
Hye how many air pressure into motorbike 70cc mondial 4strock oil pst pressure
@tazyt3388
@tazyt3388 2 года назад
Great vid cobba I run many different pressures for the terrain I’m guna ride and the bike I’m on flexibility is key a great go to is 20 front 18 rear will work everywhere on most bikes just saying cheers
@crosstrainingadventure
@crosstrainingadventure 2 года назад
For single cylinder bikes I reckon that's a good compromise for a mix of road and dirt. I know with the DR650 I have to get it up more around 25 to 30 for just road road riding or I get weird wear patterns on the front and both ends wear out faster.
@tazyt3388
@tazyt3388 2 года назад
@@crosstrainingadventure yeah the transalp is the same but for short stints between tracks I don’t change it back for the west coast dunes it 8 front 6 rear but the tyres can hold the bead well k60 scout f Dunlop d608 rear very different to the xr660 and the Xt250 I think I’ve never checked the lil XR hundy it just goes everywhere hehe
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I've never been very finnicky with air pressures. I run somewhere around 25psi both ends, maybe even 30 if there's not dirt at all. When we finally get into some serious offroad I'll go down to 20 and have rimlocks fitted.
@tazyt3388
@tazyt3388 2 года назад
@@crosstrainingadventure rim locks are the trick mate had a bugger of a time fitting them to the tubeless set up on the transalp couldn’t get a seal went to tubes but once I did the fork swap Africa twin set and 21 “ front changed the game big bor 800 kit also and remap she’s a beast jumps well handels it all I’m hoping the new transalp is as good I’ll get one if they do it right we’re spoilt for choice really u take care baz cheers mate
@RadekSkylark
@RadekSkylark 2 года назад
Thanks for the vid! Can you please comment on choice of tubes? There usually are standard tubes with thickness ~1mm, the thicker tubes of around 2,5mm and some heavy duty tubes with 4mm thickness (there may be more options I'm not aware of). What would be safe pressures to run with these tubes if you have rim locks? Should you even run standard 1mm tubes with rim locks and air pressures below, lets say, 14 psi without risking a lot of pinch punctures?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Too many variables to make specific recommendations. Rider weight, bike weight, type of terrain, type of riding etc etc.
@chrisswannie3720
@chrisswannie3720 2 года назад
Cheers for the vid - off topic but what did you use to film the parts where cam circles the biks??
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Not sure which bit you mean, it might be our 360 cam? Details in our budget drone alternative vid. Or it might be our homemade swivel cam, Chris. Details in our vid about Gopro mounts. 😊
@diegos3117
@diegos3117 2 года назад
I ride a yamaha xtz 125 (114 kg in order to ride) with tubes and no rimlocks. I use info from yamaha manuals. Yamaha xtz 125: 22 Yamaha xtz 250 lander: 18 front 22 rear Yamaha ttr 230: 15 I made a lot of tests, And go to 12 for off road My cousin use the bike and put 27 to ride rocks, just sucks.
@peter360adventures9
@peter360adventures9 2 года назад
Your in Australia maybe Queensland with the footage I guess tyre pressure is always set the same and don't really change it much I have a usb rechargeable tyre pump it's light, fast and rechargeable and can take it anywhere and easy to use plus it has a light and I also have a tyre gauge which keeps a accurate record for my needs the tyre slime is good for lots other reasons so stay upright ok
@Yapuru
@Yapuru 2 года назад
The manual of my Yamaha xt 600 E has the specifications for tire pressure but not only for road use, you have on road normal use , off road, high load , and high speed.... quite usefull
@crosstrainingadventure
@crosstrainingadventure 2 года назад
The good old XT600E, haven't seen one of those for a while! Enjoying it?
@Yapuru
@Yapuru 2 года назад
@@crosstrainingadventure yeah, i love the bike, hard as rock and really easy to ride, and i have one of the rarest models here the one with the purple tank.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I remember when the first TT500 came out when I was a teenager... talk about lusting after a bike lol.
@Yapuru
@Yapuru 2 года назад
@@crosstrainingadventure haha,lol , for me my yamaha xt its just what i need .An every day bike,not terrible on the highway, with decent offroad capabilities and not very heavy to make it easier for me to ride because my riding level isn't the best(getting better but im still a beginner).
@cedricboivin9422
@cedricboivin9422 2 года назад
If there is other people running Tubliss in here, I would like to hear your experience about the air lost that Nuetech talk about (basically they say that we should check the pressure every ride). Personally, both of my tire have been relatively air tight and the small bladder usually don't lose more than 3 to 5psi per week. I have tried it with and without slime and I have not seen any difference on that subject. Once you go Tubliss, you never go back 😉
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Ditto, Cedri... in our group it's always been about 5psi drop each week. I suspect when guys have air leaks they probably didn't fit them correctly. Funny how many refuse to read the instructions lol.
@cedricboivin9422
@cedricboivin9422 2 года назад
@@crosstrainingadventure are you talking about the small bladder or the tire ? Because personally my tire are really close to a tube for being air tight.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Inner bladder, Cedric.
@EricBanner571
@EricBanner571 2 года назад
Personally, I just run the OEM pressures on my DRZ of 18F and 20R both on and off road and have learnt to adjust my riding style. As with everything dual sport, it's a compromise.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I know some riders obsess over the perfect PSI but of course another option is just learning to ride better and actually enjoying the challenge of skating around on loose gravel. It might be laziness too in my case lol.... but I don't drop my pressures unless I'll be on dirt for most of the ride.
@sebastianmoreno3703
@sebastianmoreno3703 2 года назад
Hi, have you ever used tubliss for adventure bikes? Dr650, KTM 690, and so... How was it?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
As per the vid, you can't on a DR650 rear, Sebastian. But yeah some of our guys have used them on 18"/21" wheelsets with zero issues.
@xtcrider8270
@xtcrider8270 2 года назад
Have you guys ever ridden a husky wr250 or wr360?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Not yet
@rshawiii
@rshawiii 2 года назад
my used klx came with single rimlocks and terrible balance, shaky at hwy speed on blacktop. to balance took shitload of weights. do you recommend two opposing rimlocks?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Never tried it. I usually just slap on enough weights to stop the shakes.
@user-vf3gf4xq3v
@user-vf3gf4xq3v 2 года назад
I had a Cheng Shin front dirt tire on my DR 650 that had such a stiff carcass I could run it on 5 PSI. I had to use a die grinder to cut the bead to get that tire off my rim. Horrible.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
They are still making those?! They have been around for years now, I assumed they'd closed down. Personally I'd prefer to not go with a Chinese brand. My budget go-to-brand is Shinko... Japanese designed tyres made in South Korea.
@joedecata388
@joedecata388 Год назад
I understood spoke tyres had to have tubes? Noting the puncture coments at the end.
@crosstrainingadventure
@crosstrainingadventure Год назад
There's the TUbliss system which in effect makes spoked wheels into tubeless...
@SawyerKnight
@SawyerKnight 2 года назад
just my own experience but on my KTM500 with tubes, no rim locks and aggressive riding I run: 30 on road 20 on dirt, gravel, rocks 10-15 on sand and snow, mud never go under 10. the bike has 11k miles and 400H and I've never had a tire or tube issue. side note: I have had 2 friends on similar bikes who forgot to pump up and have ridden for hours on road with 13psi, no issues
@CesarRamirez-cn5fw
@CesarRamirez-cn5fw 2 года назад
Thanks for sharing sounds easy to remember too, I'm gonna try your recommendations
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Very interesting, in my experience at 10psi I'd have the tyre slipping a bit on the rim and eventually ripping the valve stem tube.... if I didn't have rimlocks. Those figures sound about right! One thing I love with TUbliss is you can run almost flat tyres for slippery conditions... crazy amounts of grip.
@SawyerKnight
@SawyerKnight 2 года назад
@@crosstrainingadventure yea id love to try tubliss but unless they changed it from the last time I looked they say not recommended for the road. and my bike is both a weekend dirt warrior and work day commuter
@cedricboivin9422
@cedricboivin9422 2 года назад
@@SawyerKnight no cop will notice 😉
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I actually emailed the TUbliss guys a few years back, they said zero problems as far as they could see but getting DOT approval would cost a fortune... as Cedric says the cops won't notice.
@arnandegans
@arnandegans 2 года назад
Up to 20%? Most service stations I've been to have no gauge at all. Just a compressor, IF that...
@stevemacca786
@stevemacca786 2 года назад
Just converted my 480rr to adv spec. On dirt roads…for fun factor it’s hard to beat about 26psi and a rat shit bald rear knob. Sliding around effortlessly, good GT 216 up front with about 12 psi. Happiness
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I loved my RR480, Steve... fun in the dirt and on dirt roads. I assume you know about replacing those plastic gears at 100 hours?
@stevemacca786
@stevemacca786 2 года назад
@@crosstrainingadventure yes did it at about 90, did not go the steel route as the plastic is basically only a few dollars worth.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
👍 Yeah those steel replacements are expensive.
@rs5001988
@rs5001988 2 года назад
18psi all I ever run F/R xr400 on off road works ace for me
@crosstrainingadventure
@crosstrainingadventure 2 года назад
The mighty XR400! I think that was my first ever bike vid shot on video tape lol. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MdWW1a1q7RI.html
@robsonenduro3316
@robsonenduro3316 2 года назад
just kick your tyre good if it will not touch the rim you're good to go. Personally I move slowly towards mousses on front wheel.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
For dirt riding I gave up using a gauge years ago... just put a knee into the tyre to check it. 😁
@postmortemspasm
@postmortemspasm 2 года назад
KLX650R at 25psi cause i really hate flats and dont really mind sliding around
@crosstrainingadventure
@crosstrainingadventure 2 года назад
The green hippo! A real shame they discontinued these, I had a ball with mine years ago. A very old vid from 2008.... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-tu8N1XYO284.html
@sethnaughton2111
@sethnaughton2111 2 года назад
Xt500 22psi
@justgjt
@justgjt 2 года назад
I've gone as low a 8 psi with rim locks on skatey pea gravel and held back on the throttle.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
What sized bike?
@eatsleepplayrepeat
@eatsleepplayrepeat Год назад
What's the absolute lowest PSI for deep sand on a 500 pound bike?
@crosstrainingadventure
@crosstrainingadventure Год назад
Rider weight? Luggage? Rim locks? How stiff are the tyre sidewalls? Ply? Tubeless or what type of tubes? There's no one size fits all answer.
@jgruen9854
@jgruen9854 Год назад
0psi
@eatsleepplayrepeat
@eatsleepplayrepeat Год назад
@@jgruen9854 i cant argue with that
@huskypoop4917
@huskypoop4917 2 года назад
eyup bazza i want some knob firming air send me the link
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Clamping knobs for males? www.bolt.com.au/handles-knobs-production-clamping-handles-male-c-2285_2295.html
@huskypoop4917
@huskypoop4917 2 года назад
@@crosstrainingadventure cheers baz ;D
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Warning, I have tried these and have been in lot of pain for several months now. 🤔
@huskypoop4917
@huskypoop4917 2 года назад
LMFAO ;D
@huskypoop4917
@huskypoop4917 2 года назад
@@crosstrainingadventure LMFAO ;D
@wv4life375
@wv4life375 2 года назад
I find 13.4 psi to be the perfect tire pressure any deviation of even 0.1 psi and I become a sucky rider.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Same here... although I find tongue positioning and the correct amount of eye squinting are critical to get it right.
@wv4life375
@wv4life375 2 года назад
@@crosstrainingadventure my wife agrees with that technique
@crosstrainingadventure
@crosstrainingadventure 2 года назад
😂
@tolga1cool
@tolga1cool 2 года назад
As a European watching this I need a second window open to calculate the pressures in bar every five seconds
@crosstrainingadventure
@crosstrainingadventure 2 года назад
But 1 bar = 100kpa so I figured it's an easy conversion. There would just be too much clutter on the screen if I gave all three measurements throughout the vid.
@tolga1cool
@tolga1cool 2 года назад
@@crosstrainingadventure Oh boy. I'm a bit dense as it turns out. Didn't even see the conversions on screen. That's what you get for whatching RU-vid on a phone screen while cooking...
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I keep forgetting lots of viewers are using their phones! I edit and watch vids on a massive tv set and then I have trouble with my eyesight sometimes lol. Enjoy your dinner... 😎
@tolga1cool
@tolga1cool 2 года назад
@@crosstrainingadventure Thanks! Dinner turned out pretty good actually 😅 Anyways. I usually like watching on bigger screens too. But in the kitchen the phone comes in handy. Either for recipes or the occasion enduro video 🏍️💨
@clemoniii
@clemoniii 2 года назад
I love Tubliss on my 2T Betas, and ran it on a tagged 450 EXC I commuted on. However, didn't think they were advisable for twin cylinder ADV bike (Tenere 700) due to chances of extended asphalt rides and speeds over 80 mph. Have you heard more recent test info, or am I doomed to dealing with those ANNOYING tubes again? YES, I fully accept the dangers of taking advice from pink tutu wearing Muppets. No need for caveats.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I did ask the TUbliss guys if they'd ever do a 17 inch setup for the DR650, Clinton... (maybe). I asked about the adventure bikes and they said it's just too expensive getting DOT approval but they couldn't see problems running the system on bigger bikes, as long as the rims are still narrow. T7 rear rim is probably too wide. 🤔
@clemoniii
@clemoniii 2 года назад
@@crosstrainingadventure I don't worry about a DOT stamp, but thanks for mentioning the rim width issue. Did they give max rim width info?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
No but the website will tell you all the models they can fit
@clemoniii
@clemoniii 2 года назад
@@crosstrainingadventure I'm embarrassed to say I found that last night. Sorry to bother you with such an obviously easy to answer question!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
No worries, Clinton! As you probably know I usually don't go looking for links unless someone has really had trouble finding it... and offers a large cash incentive lol.
@MrDavidfuchser
@MrDavidfuchser 2 года назад
Wiggle and pull the tool
@crosstrainingadventure
@crosstrainingadventure 2 года назад
That's what she said
@davidfindlay5432
@davidfindlay5432 2 года назад
Tubliss, resistance is futile.....
@crosstrainingadventure
@crosstrainingadventure 2 года назад
😂 True dat.
@lwil6393
@lwil6393 2 года назад
I have converted tube type spoke wheels to tubeless tires using the following method ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JPzoqi_4X7o.html Have done 2 Africa twins, 2 CB500x with Rally Raid wheels and 1 Kawasaki KLX 300sm and all are still working fine, in loose terrain and slow going I have run down to 10psi. The video is done by an engineer who is quite anal. The only thing I have done different is giving up on his 17$ aluminum valve stems and simply cut the stems out of old inner tubes (use the round circle as the guide) Use the Marine calk to seal the stem and run tape over the top of it cutting an air hole so the whole thing works. Barry experiment on your DR and let us know how it goes!
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I thought about it but the problem is so many guys report failures with the DR650 when they've tried... even with the DR650-specific kit you can buy. I'm just going heavy duty tubes instead with some Slime inside to minimise pinch punctures.
@lwil6393
@lwil6393 2 года назад
@@crosstrainingadventure The advantage of the tube is the ability to run lower tire pressures if you have rim locks installed. I have run the Tublliss system and Nitro Mousse. For Dual sport use I will follow the video and convert spoke wheels to tubeless with great confidence. Thanks for all your great work.
@janeblogs324
@janeblogs324 2 года назад
Coincidence that Brett tkacks just released a video on this??
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Brett who? Are you suggesting he copied my video, Jane?
@crosstrainingadventure
@crosstrainingadventure 2 года назад
I found him... you mean 'Bret Tkacs'? I couldn't see any recent vid of his covering air pressure. And in any case I first covered this topic on my enduro channel back in 2016, so maybe he's copying me. 😂
@janeblogs324
@janeblogs324 2 года назад
2 days ago he did a myth video. I'm not saying you copied him lol, just coincidence Check out his videos, he teaches seminars on enduro/adventure riding.
@-MORK-
@-MORK- 2 года назад
Tubliss with a 505 cheater out back - 5psi. Anything less than 15 up front with the fatty feels too dead and steers like Russian tank.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
On what sort of bike?
@-MORK-
@-MORK- 2 года назад
@@crosstrainingadventure 06 KTM 300 XC - made a world of difference in the silt and deep sand in Utah and the rock/gravel single track here in Colorado. On the F800GS, I have to drop just a bit below street pressures on the rear Motoz tractionator or else it just digs straight down. Maybe 25 is as far as I go. I keep the front at street pressure due to the weak design of the factory rims.
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Gotcha. Yeah I love TUbliss! I run something like 2 to 3psi front and rear on my Beta Xtrainer for all our slow gnarly rides... works a treat.
@mattkeating7446
@mattkeating7446 2 года назад
80psi never worry. Lol
@crosstrainingadventure
@crosstrainingadventure 2 года назад
😂
@supermick83
@supermick83 2 года назад
I love the video except the image of me in my Speedos you clearly stole off my Facebook page. I demand you Photoshop me to have the physic of a Greek god
@crosstrainingadventure
@crosstrainingadventure 2 года назад
Looked damn fine just the way you are Mick... a babe magnet! 😎😂
@supermick83
@supermick83 2 года назад
@@crosstrainingadventure yeah I'm a regular Don Juan.. the ladies Don Juan anything to do with me🤣
@crosstrainingadventure
@crosstrainingadventure 2 года назад
😂
@unclebadger597
@unclebadger597 2 года назад
Best air pressure is manufacturer recommended. Air them properly and leave them alone.
Далее
3 top myths for riding offroad on an ADV bike
14:32
Просмотров 315 тыс.
Каха и суп
00:39
Просмотров 1,8 млн
I Tried Solid Bike Tires | Here's What I Found
13:14
Просмотров 880 тыс.
Motorcycle Riders - You're Leaning the Wrong Way
7:04
WHAT IS FOR YOU ? TUBES vs MOUSSES vs TUBLISS
8:04
Просмотров 138 тыс.
How to fall off your ADV bike - are you in this video?
15:46
How to Check and Adjust Your Tire Pressure
22:58
Просмотров 65 тыс.
Bellingham vs Referees 😪
0:18
Просмотров 4 млн
Лёгкий спарринг.. 😅
0:11
Просмотров 856 тыс.