No video :(

How to program a PIC microchip?

Подписаться 1,6 тыс.

Просмотров 13 тыс.

50% 1

Is it worth to learn PIC programming in 2023? I think so. There are numerous fun projects that you can do with it. Ranging from Blinking LED project to Retro Hardware mods. This video shows you how to start programming in MPLAB X and XC8 compilers. This project uses a K-150 Programmer to upload the HEX file onto the PIC chip.
Links in the video
PIC16F628 product page
www.microchip....
PIC16F628 datasheet
ww1.microchip....
Download MPLAB X
www.microchip....
Download XC8 compiler
www.microchip....
PIC Projects
circuitdigest....
atariamiga.free...
github.com/sea...
K-150 PIC Programmer software
www.kitsrus.com...
K-150 PIC Programmer USB Windows Drivers
buyhere22.com/...
Music used by Jason Shaw:
audionautix.co...

Опубликовано:

20 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@sportsmindfastfurious834 7 месяцев назад

Informative and clear explanation

@j.r.scaryy 5 месяцев назад

Yes, Windows 7 is outdated, but it was and STILL is the best windows yet, in my opinion. Excellent video.

@ezContents 5 месяцев назад

Thanks. Yes, I agree. It was / is my favourite Windows version.

@tyt1638 3 месяца назад

@@ezContents yes. 7 is light and require short time for booting.

@burstfireno1617 2 месяца назад

thank you 👍 subbed

15 дней назад

How to read code from pic16f628a?

@oveschleisner-meyer8139 5 месяцев назад

Good information. How can I make a code for setting an output by a pushbutton as a input...? Do you have any tutorial for this?

@SX1R 10 месяцев назад

I still use my veteran Veleman P8048 board, but I connect a a Pikcit 3 on the ICSP header. right now it has a 4 MHz crystal and a PIC16F84A mcu. The part around the serial port is no longer in use.

@ezContents 10 месяцев назад

That's a nice solution. Maybe I will try that one out. Thanks.

@sharkstars8627 4 месяца назад

Can i used rt809h for that

@jonaswalsch9787 Месяц назад

Hey, the link to the website where you can download the K-150 PIC Programmer USB Windows Drivers software seems not to work, is there another website?

@witchking453 11 месяцев назад

I have K150 programmer too. But as you said that the K150 chip supports only the operating system of Windows 7 SP3 and below. Then i quit trying after that. I didn't check for years. We need a new programmer 😁

@ezContents 11 месяцев назад

I could be mistaken, but I thought that I saw the Prolific drivers for Windows 10 somewhere.

@modorangeorge4991 4 месяца назад

Pl2303 driver works in Windows 11 too. I have few devices based in it, no issues

@magicsmokeescapist4069 2 месяца назад

You cauld sniff the web for a Pickit 2 if you're only prgramming PIC mcu. They work in both Linux (with manditory faul language) and even Win 11 Nte win software are free for the PK2.

@witchking453 2 месяца назад

@@magicsmokeescapist4069 Thanks, I'll try that 👍

@CRP-lr3jm 11 месяцев назад

RA4 GPIO of PortA is an open drain port so, can LED's be interfaced to other PortA pins (which are stated as CMOS) in current sink or current source methods? Also can an Switch be interfaced to RA4 with an 10k resistor pulled up to Vcc and switch connected to ground to read an active low signal when the switch is pressed?

@ezContents 11 месяцев назад

On that pin you have GND or a floating state/high impedance. So you will need a pull up resistor for it to work.