No video :(

How to remove a BMW E83 X3 Transfer case & Transmission

Подписаться 2,7 тыс.

Просмотров 36 тыс.

50% 1

In the following video, I walk the audience through the procedure of removing the transfer case and transmission on a 2007 BMW X3 3.0SI. This process is nearly identical for all E83 models and is similar for the E90 3series and as well as some X5 models.
Thanks for watching. Like & Subscribe

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@MangoPickle Год назад

Nice job showing how it's done. Good lighting. I have same symptoms and need to replace on my '09 X3.

@stuartbear922 Год назад

Good video! Nice to have your own lift.

@MrMagsimus 6 месяцев назад

Excellent job bro very clean and presentation was nice ❤

@lyonkennedy5588 27 дней назад

Thank you for this video. I have a 2008 BMW X5 3.0si and my mechanic told me my Rear Axle transfer case carrier is completely rusted/rotten and is unsafe, and if the carrier brakes the transmission and transfer case will drop/hang causing other damage to the drivetrain and underbody. Unfortunately I did not take a good look at what he showed me, but would you happen to know what exactly is the rear axle transfer case carrier is? I've tried searching images online, but I only see what the transfer case looks like, but have no idea what the case carrier looks like.

@khalidjj2073 5 месяцев назад

Where is the installation vidro...Btw, Great video. You made it look so simple Good work Mine, 2005 x3, slipping, hunting, did pass ca smog test...

@uniquecovering8095 8 месяцев назад

hi i wondering can i removed the transfert case with the jack with the car be up ?

@ytfeverguy8367 Год назад

Big job. Great vid.

@brarautorepairs 8 месяцев назад

The GM transmission was used on various N52, N51 transmissions. I think it is called the GA 6L45 made in France for high end GM products in 2006+ Cadillacs. ZF wasn't able to provide enough transmissions to meet BMW requirements so BMW only used the ZF in high output applications. The GM transmission is actually my favorite because it's easier to maintain and doesn't have issues with the sleeve like the ZF, has a regular filter and pan and takes Dex4. It even shifts better than anything made by GM because BMW has their own in-house software. I've rarely seen them go bad on N52 when the fluid level is maintained and replaced every 100k

@ytfeverguy8367 8 месяцев назад

My GM trans is mated to M54 engine. I have cold start issues (Reverse, D slippage). A partial drain and refill (above fill plug engine running) with Dex6 and Lucas additive has restored normal shifts when warm (cold start issues remain in lower Fall winter temps). @@brarautorepairsCurious what might be causing cold start issues torque converter, valve body, solenoid, worn internal clutches, pump? I am considering a reman or good used GM trans.

@ron8566 Год назад

Will we see a video on the rebuild phase? I hope so. Thank you.

@Rurik_JustCruzn Год назад

Sorry Ron, I was on a time constraint and wasn't able to film the install.

@dr.hassankhalil9963 Год назад

Hi I have a problem in my x3 e83 2009 Transmission Fault code 5658 gearbox position sensor malfunction. I purchased one and after installing the same fault code. Is there a method to test the sensor before installing. And if I want to install a new valve body with sensor, does it need to be programmed or it can be installed directly?

@mtbridingog9083 10 месяцев назад

I wonder if the car will be faster if a new longer driveshaft is installed and if it will get better gas mileage.. I’m thinking about removing it .. I already took out the front prop shaft because the shaft coupling was destroyed so my 2007 3.0 x5 is rwd only .. I wonder if the gearing will be the same if the transfer case is removed and a longer drive shaft is installed from the rear diff to the transmission..

@90octavian Год назад

Hey boy where is the position of the pipe from the top of the case transmision ?

@davebarbieri1380 2 месяца назад

If just removing transfer case, is it necessary to remove exhaust?

@Rurik_JustCruzn 2 месяца назад

It would be near impossible to access the mounting bolts and drive shaft bolts without taking the exhaust off.

@joebenson658 11 месяцев назад

Did you swap this out with another transmission if so did you have to program the egs / tcm to match the vin ?

@yoshixx1238 5 месяцев назад

With the bmw x5 e70 style 2007 to 2013 you need to reset to ceros the ISN numbers, but if you dont want problems remove your original internal valve body and install on the used transmission, i had a problem with isn two times with bmw x5 both not running because of that only in parking gears will not work

@Enduro_Urbano Год назад

hey good video. What were the symptoms of the transmission?

@Rurik_JustCruzn Год назад

Hi Enduro. The transmission was slipping during gear change. The revs would climb while the speed remained constant.

@Enduro_Urbano Год назад

@@Rurik_JustCruzn thats exactly what my transmission is doing on my 07. Did you try changing oil/filter on it first? I am going to try that before replacing the transmission