Тёмный

How to Remove and Replace a Strut Mount - 1998 Audi A6 Quattro 

Ratchets And Wrenches
Подписаться 1,1 млн
Просмотров 49 тыс.
50% 1

Опубликовано:

 

29 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 30   
@josenoriega1994
@josenoriega1994 10 лет назад
Come to PA we have lots of pot holes lol . Roads here are horrible because of salt . I need to get my outer tie rid done soon on my 2001 audi a4 after watching this it helped me understand it more.
@myRatchets
@myRatchets 10 лет назад
Haha I've never been to PA but yea maybe someday I'll pay a visit to PA and all of its potholes lol. Replacing the outer tie rod is pretty easy, I've been really itching to make a video on it too, but havent had a car that needs it yet. GL
@josenoriega1994
@josenoriega1994 10 лет назад
would i need any type of alignment after ?
@myRatchets
@myRatchets 10 лет назад
If you are replacing the outer tie rod yes. You wouldnt have to for the strut mount replacement. GL
@sobyx1
@sobyx1 4 года назад
Awesome attention to detail. Using channel pliers to hold strut didn't work all the way due to blue locktite, kept working the nut tull it came loose.
@brett1234
@brett1234 7 лет назад
I love your channel. I'm thankful that I have an 1998 Audi A6. I'm about to change my brakes soon so, a lot of these videos are helpful. Thank you!
@626nh
@626nh 8 лет назад
Very informative video. Excellent description.
@jmgiron4
@jmgiron4 9 лет назад
Well done!! Excellent video. Now I feel more confident doing mine this weeked.
@myRatchets
@myRatchets 9 лет назад
jmgiron4 hope it went well, cheers.
@torgut9
@torgut9 6 лет назад
Almost 5 years old video but still helping people out! :D I have exactly same pop-sound-issue (supportarms and balljoints are all new and good) with my old Passat B5.... and it appears right after I changed front shock absorbers. I'm 99% sure this will fix my poppings. Thanx for this tip dude (^_^)
@martinboyce4293
@martinboyce4293 7 лет назад
You the man! Wish I had your knowledge and skill set!
@dabid5
@dabid5 3 года назад
that's a lot of tricks you don't see elsewhere!
@99AUDI99
@99AUDI99 10 лет назад
I’m pretty sure it was loose Strut top Nut and not strut mount(on video it looks fine). Also I would check strut - while in there. I had the same popping noise, I tighten strut nut and popping noise disappear.
@kintech4585
@kintech4585 10 лет назад
I might have a similar situation so this is a perfect timing. Do you I can wait this out till summer? What do you think might happen if i ignore this kind of strut mount problem?
@myRatchets
@myRatchets 10 лет назад
I guess if it is indeed the mount a minor noise it should be fine, but you can always just get the strut assembly out, buy the mount and take it like that to a shop and have them put it in their bench spring compressor and replace the mount under 5 minutes.. they usually only ask for a tip or $20 bucks or something. But it cuts down alot on your repair time. GL
@PaulBissekerBushcraft
@PaulBissekerBushcraft 6 лет назад
Thanks ;)
@rubenquiroga300
@rubenquiroga300 8 лет назад
cuando apretas el bastago del amortiguador con una pinsa tenes que cambiar el amortiguador!!
@ryanhutzel7897
@ryanhutzel7897 8 лет назад
how the hell do I do the rear there's no place for a vice grip it's just spinning freely
@DaOneEnOnly
@DaOneEnOnly 10 лет назад
Thanks for the video. You should not use a pry bar on the pinch joint. Instead use a ball joint fork / separator. LOL "...it is likely you'll have to replace your motor..." Sometime that is the painful truth.
@myRatchets
@myRatchets 10 лет назад
Haha yea I was gona say motor mounts..but caught myself halfway. I do have a ball joint fork/separator but it actually does more harm than good..as in it damages the rubber boot that keeps the grease in and that causes premature failure of the ball joints. The pry bar was more for causing vibration than to dig in there.. it did no harm. cheers
@DaOneEnOnly
@DaOneEnOnly 10 лет назад
Good to know. My concern was indeed with deforming the joint with the pry bar.
@MrStroller4u
@MrStroller4u 5 лет назад
where is the 2.7t?
@hllywd964
@hllywd964 10 лет назад
where do you live?
@myRatchets
@myRatchets 10 лет назад
socal :)
@hllywd964
@hllywd964 10 лет назад
oh I wish...I'm on Long Island in NY in snow hell!!...
@myRatchets
@myRatchets 10 лет назад
I lived in Boston for a few years..know how you feel!
@twotimes2099
@twotimes2099 7 лет назад
12:26 Not trying to be rude but putting your hand where you did was about the dumbest thing you could have done. think about losing all four of your fingers and having this video to remind you every time you watch it? Please for the love of God just don't make that mistake again
@nedudki
@nedudki 6 лет назад
dumbest thing to use air gun on the shock...... terrible
@tonymartinez1able
@tonymartinez1able 6 лет назад
Security first always. But, If he had expanded the spring then yes, but he compressed it. in case of failure the gaps will open not close.
@VortechBand
@VortechBand 5 лет назад
@@tonymartinez1able The compression force is enough to launch the spring across the street. Your fingers will fly with it. If you are lucky, it will just break your finger bones.
Далее
How to Tell If Top Mounts Need Replacing
7:06
Просмотров 197 тыс.
This is how Halo felt as a kid 🤣 (phelan.davies)
00:14
Audi TT MK1 Suspension *How To guide*
25:37
Просмотров 40 тыс.
Here's Why You NEVER MESS WITH A SPRING COMPRESSOR!
8:57
How to make coil over struts, affordably
17:02
Просмотров 56 тыс.
This is how Halo felt as a kid 🤣 (phelan.davies)
00:14