@@DiyGuy50 ok, thanks. I just purchased a rental property and the windows are in rough shape. This video makes me STROOONG! 🤣 (like that goofy Drive Time commercial).
Solid Video! This video helped me remove an old window on my 1865 house and properly install my first new vinyl replacement. This was my first time and success thanks to this video!
I searched everywhere trying to determine the issues involved in just leaving the storm windows in place when replacing old windows. I found nothing. Then I watch your video and you just do it without any issues. Thanks.
Thanks for sharing! I did end up taking the old storm windows out, though. They were in bad shape. However, I did leave them in until the new window was installed. The only issue with leaving the storm windows on is it makes it difficult to put silicone caulk around the exterior of the new window which I think should be done even if you do keep the storm windows.
@@DiyGuy50 Appreciate your situation. Mine may be a bit different. I'm in Maine where the "storm" windows also slow down the winter temperatures even with new windows. I get that if I take off the storm windows I will need to then caulk but what I really want to do is replace these windows on a second floor in the middle of winter with snow on the ground. My storm windows are a sort of a double pained version so I think I can actually caulk too without removing the frames. Always looking for a safer and easier way to do things!
Thank you so very much! I am faced with having to replace 60 year old windows on my house and though I'm pretty handy, I was intimidated and considered professional replacement installation instead. You have given me the confidence to tackle this task on my own! Thank you!
Great video! I'm wanting to replace my windows without breaking the bank and you have one of the best videos I've watched since researching how to do it. Thanks!
Great video, thank you for taking the time to show the small but important things like if its square nothing like pulling my window then realizing when I pop the new one its not going in. Awesome thx.
You made this look so easy! Hopefully purchasing a house that needs all windows replaced, unfortunately. I can only hope this can go smoothly doing this myself.
Take good measurements and check the squareness of the window. If the window is square, you can get by with ordering a window that is 1/4 inch shorter in length and width. However, if it’s not, you need to take more than 1/4 inch off or the new window won’t fit! This is very important! Also, I don’t know your experience and skill level when doing these kinds of projects. If you don’t have much experience, it’s probably best to try one window before ordering them all. It could be very costly if you don’t measure correctly and they don’t fit! Thanks for sharing and good luck!
Great video. You did a great job filming the removal of the old window and a fantastic job showing how to install the replacement window. It's so difficult finding videos on how to install window inserts. Most windows are the front screw in kind.
@@DiyGuy50 I will do. Because of your video, I learned that the stop trim isn't a part of the window. I had no idea until you explained and demonstrated it in your video.
Thank you sir for the easy explanation. I just bought a house that has old woodframe windows that I want to change out in the near future. At least now I have an idea of what Iam up against.
You did a great job !!!!!!!!!!! You really explained the process well. If the windows are really old and have weights in the sides, is there a different process? When you are done, can you remove the old storm window outside? And, on the last step of replacing the trim on the sides, can you add a piece of trim at the top? Thank you for posting this video !!!!!!!!!!!!!!!!
Thank you! The only thing different with the windows with weights is you need to either remove the pulleys or hammer them flush with the window jambs so they’re not in the way when you install the replacement window. And, yes, you can install a trim piece at the top to improve the look. The house in this video did not have those pieces but many do. Not shown on this video, I removed the old storm windows and caulked the outside of the window and and installed a bottom piece that came with the new window. You’ll have a gap at the bottom of your window on the outside that you will need to fill and seal. I used something called “Poly Foam Caulk Saver by Frost King”. It’s tubular foam that comes in a roll and various diameters . Cut it to length and stuff it in the gap and cut the plastic strip that comes with the new window to the right size and install it. Then put a bead of caulk around it.
@DiyGuy50 Thank you so much !!!!!!! I only replaced one window, my friend did it for me, but I watched him do it. Your video looked closest to what he did. I am going to try doing one myself. If all goes well, I will replace the others too. I am a Whistleblower, so my life is very difficult. I have not had heat since 2012. And I do not get any assistance. I thought replacing the window would keep the house warmer. Thank you sincerely !!!!!!!!!!!!!!!!!!!
Who needs jobcorp or college with videos like this. You can learn alot of stuff on youtube and make a business from it. I learned how to be a barber by watching youtube and never went to barber school. Sucks that you have to go to school for certain hours in order to get certified. They should give you an option of taking a test without taking the courses and if you pasd you get certified. Alot of people with potential are not doing this because they have to put the hours in school.
Thanks for the detailed video , I am going to give this a try - do all windows have to be ordered ? Or does Lowes & Home Depot keep some standard sizes in stock ?
Hi. I didn't have to cut anything off. The window was plug-and-play. I ordered these Wincore windows from a local builder's supply company and they come ready to install.
Anywhere two different pieces meet there is caulking. Otherwise there would be a very noticeable dark line. Its common practice and should not be surprising. A bit of Caulk & paint makes a carpenter what he aint.
Our contractor removed most of the interior wood trim around the window including the stop/sill, trim up the walls snd below the stop/sill breaking 2 of them. Insulation left on the floor. Was supposed to be a replacement only with same size. Wondering what he did. Left us more repairs and costs.
Hi. I removed the storm windows after I installed the new windows. I took the old windows out to measure for the new ones, so instead of putting the old windows back in while waiting for the new I just left the storm windows on.
@@DiyGuy50 Thanks! did you have any issues removing the storms? Did you just fill any screw holes with caulk? did you need to paint after removing? thanks again. you got a sub from me!
@@dylan1235x No issues removing the storm windows . I only left them in because I took the old windows out to measure for the replacement windows and I knew it was going to take a while to get them. Just take the window panes out first and then it’s easier to remove the frame. Thanks for subscribing!
@@dylan1235x And, yes I filled the holes with wood filler (you can use paintable caulk as well ) and painted the exposed wood. Use silicone caulk around the exterior of the new windows. My replacement windows came with a strip of vinyl about 1” wide and as long as the width of the window. This can be cut to the width of the gap at the bottom of the window. It gives a cleaner look than caulk if that gap is very wide.
Thank you. My old windows have those weights behind the sides.... so basically youre just leaving the frame and weights there, and measuring inside? ...and i thought it all had to go.... this seems way easier, or is my situation different? TIA
Yes. The frame is not removed with replacement windows. The weights in the frame are not removed. The pulleys should be removed or hammered flush with the frames . Thanks for your question!
Your situation is exactly the same as mine except for the weights. And you’re right. A “replacement “ .window is much easier to install than a “new construction “ window .
Where are the screens? The storm window frames also held the screens in old homes I lived. I do not see any screens for the new windows...? Do people like bugs and birds flying in nowadays or does no one open windows anymore. What am I missing? 😊
Hello! I'm hoping you'll be able to tell me where I can get more of these windows and screens with that slide "thingy" at the bottom to raise/unlock & lower/lock. Looks like their in this video on the outer side of the window you just removed. Hope you can help. Thanks.
Good video and explanation of the process. If the old wooden window has a metal track guide along the sides are they removed as well as the sash stops? Thanks
I’m not sure because I’ve never ran into that situation, but I think you would have to in order to put your replacement window in. In the houses I’ve done, the replacement window slides in leaving about an 1/8” gap between the side jams. When there are pulleys in the side jams I just hammer them flush with the side jams but I don’t think that’s what you’re talking about. Hope this helps. Thanks for watching!
I’ve never measured for thickness. I think it’s pretty standard. Occasionally, I have a small gap between the replacement window and the sill, but, normally it’s a perfect fit!
I have to replace all my windows in my new/old house they’re double pane with storm windows. The kitchen and the bathroom have slide ups the kitchen one I definitely want to make bigger. Hopefully I can do this by myself.
If you’re putting a bigger window in, you will be cutting a bigger opening and installing what’s called a “new construction window”. My video shows how to install what are called “replacement windows”. You’ll need to do your homework if you’re not familiar with installing “new construction windows “. Thanks for commenting!
I have my windows made to order by Famous Supply Company in Byesville, Ohio. They’re locally owned and operated. I don’t know if they ship orders or not, but you could look them up and check. If not, there’s probably someone like them nearer to you. Let me know. Thanks for your question and good luck!
buying my first house at 26 yr old it has single pane windows trying to get an idea of if this is within my skill level or not, I've done flooring and small bits of drywall along with numerous other things. still not sure about this though
That’s a good question. I don’t replace windows for a living so my experience is limited. I’ve never had the privilege of replacing windows in a house with marble window stools. Personally, I think the marble sounds like a nice touch, though!
So dumb question. I live in a 200 year old stone house. The window sills are 22 inches deep. The windows are ancient. Basically, i just pull the window out and keep the old frame in?
If the frames are in good shape I don’t see why you couldn’t. I love old houses but they present many challenges. I would talk to the people you plan to order the windows from and make sure that a replacement window is applicable in your situation.
Does anybody knows what's the wood used to make the stool? My biggest fear is to get the old window out ,run to lowes or home depot and the don't have the measurements that i need..it doesn't make sense to take out all windows and measurements then look for replacement
With replacement windows, as opposed to construction windows, You don’t need to replace the entire window if the window frames are in good shape. So the old sill, stool, side jams and head jam (the window frame), does not get removed. Unless, of course, they’re in too bad of shape. If they are, the whole window, frame and all, must be removed and replaced with what’s called a new construction window. Also, it’s not likely that you’ll be able to get replacement windows for an old house at any home improvement store like Lowes. They have to be ordered from a place that makes windows to your size.
Wait, I need to remove the existing window (the glass is oxidized) and add new ones. Did he just place the new window in with out removing the old one (Meaning, I see old glass still there on the outside)?
The old glass and window you’re referring to is the old storm window I had not yet removed. It was still chilly outside when I removed the old windows so I left the old storm windows on until I had the new replacement windows installed then I removed the old storm windows.
@@newroadchurchaustintownohi728 I have always removed both of the window sashes to accurately measure height of the opening. But you can get by with just removing the lower sash.
Yes. Old storm windows that I left in place until I had the new windows installed. Then I removed them and used a good silicone caulk to seal the out side of the new windows.
How important is it to use foam? I have a loud road behind me and I only have dual pane vinyl low-e windows. Contractor says he doesn't use foam in case of any repair or or replacement.
The foam is not necessary. But the gaps should be filled with insulation of some kind. I often stuff fiberglass insulation in the gaps using a paint stir stick or anything that works. If you do use foam, make sure it’s the foam specifically for windows. If not, it expands too much and the window is hard to open and close. Great question! Thanks for commenting!
@@garygoodwin3461 Yes. I left the old storm windows on until I had the new ones installed. I then removed them and used silicone to seal the outside of the new window.
The old storm windows were taken off and any exposed wood on the exterior of the old window frame was painted, and a bead of silicone caulk was put around the new window.
I realized you kept the exterior storm windows. What made you decide to keep them? If I’m going to replace my windows I’m struggling what to use to cover the expose external trim when i remove the storms
Hi. I took the old storm windows off. I left them on until I was ready to apply silicone caulk around the exterior of the replacement windows . This house had aluminum siding and the original exterior trim on the windows had been clad with aluminum and was in good shape.
@@DiyGuy50 so I have the same, aluminum siding and trim. My issue is how do I cover the expose wood trim once I remove the storms? There will be a section probably the same width of the storms. Did you just caulk that?
I own several rentals and have flipped quite a few houses and have always Wincore windows. They’re reasonably priced, ( average sized windows are just less than $300/window. No complaints from me so far. Idk how they are as far as noise reduction, however. Thanks for your comment!
I got told by a contractor that my trim around my window couldnt be reused! He said it would be $65 in labor extra to stain n install new trim, then he said the sill piece at the bottom, would be gone! I see you didnt remove any of the outside trim around the window(casing), why did he tell me that?? Also the trim outside would be gone! And my storm windows outside have to go too!
I’m not sure. It sounds like the contractor was talking about installing what are called “new-construction” windows as opposed to “replacement windows”. With replacement windows, none of the trim needs to be replaced.
Are you being serious?? I’m not sure why you would want to replace new windows but you would replace them the same way you would replace old windows. Watch the video if you’re serious about properly measuring.
Lol, I don’t know! But the house in this video was almost 100 years old, so it had a lot of paint and caulk! Replacing the whole window is usually not necessary and it’s a lot more work! The multi tool cuts right through the years of paint and caulk.
Our house is also almost 100 years old and the windows are caulked shut from the outside.. 😩 I decided to try to open one in the living room today, hoping to have 1 window in each room that opens, but it was also NAILED shut.. why??? 🤦♀️I managed to slide a hacksaw in and cut the (thankfully) small nails. My husband did mention getting a multi-tool like that! It's not safe to climb up from outside and unscrew the storm window to pry open from outside- I did this with my dining room window- because of uneven ground and a stone wall that drops off. Also a crepe myrtle tree doesn't allow for better positioning of a ladder.... so that's why I started looking up videos on how to just replace it. It looks really rough at this point now too, after all the trying to force it open.. 😬
Oh, I misunderstood your first comment! I thought your we’re considering putting in a new “construction “ window, as opposed to just installing “replacement” windows . Replacement windows are not difficult to install once you get the old ones out., but yes, the paint and caulk and nails do make it difficult! Good luck!
The flashing tape should be installed around the entire opening, not just the bottom of the opening. Similarly, the interior casing should have been removed and the foam should have been applied around the entire jam! There’s certainly a 1/2” gap around the entirety of that old rotten jam and it needed replacing more so than a coat of exterior white. Kind of a rush job imo.
Ok, Victor! How are you? First of all, the “jambs” are not rotten at all. There isn’t a half inch gap around it and removing the interior casing is completely unnecessary as is the flashing tape around the entire opening. Thanks for commenting though!
The foam around the window is completely unnecessary, i install windows for a living and i never would have thought about using foam there, i just use high grade caulking and seal up the edge of the window
@@DiyGuy50 He is just pissed at the fact that you showed to everyone how easy is to do the job he taught he is valuable and irreplaceable. Just realized anyone can do what he does without paying people like him ridicules amounts of money…
The facts are, that restoring your windows makes far more sense than replacement windows. A properly restored and weatherstipped window with a storm is as energy efficient as a new window and it doesnt have seals that will fail in 10-12 years. Replacement windows are a scam
@@jamesjoslin7586 Replacing a historic single-pane window also will not save you much money in the long run. While the exact figure will vary depending on the type of window installed and whether or not a storm window is used, studies have found that it could take 100 years or more for a replacement window to pay for itself in energy savings. According to information published in a recent Old House Journal article, it could take 240 years to recoup the cost of replacing a single-pane window-storm window combination with a low-e glass double-pane thermal replacement window. Also, a historic wood window can easily last more than 100 years, while a new window may not last 25.
@@victorianantiquities What about re glazing/ painting a “ historic “ window ? Very high maintenance that could be made even more so for high or hard to reach ones. Also, drafts, sweating would be a concern let alone more energy consumption. Lastly. There are very few improvements that actually “ pay for themselves “
@@jamesjoslin7586 It deos not take that long to reglaze an paint a wood window. Using quality materials, the time before you will ever have to do it again is quite long. Also with a good storm the old windows will not deteriorate. People like yourself have been conned by the window replacement industry to buy these plastic windows with 10-12 year life span. I have 140 year old house with 28 original windows. 3700 Sq. My heating budget is 92.00 a month. I could spend .tens of thousands to replace them but I never recoup that cost in my lifetime. The most efficient way for a home owner to save money, is in attic insulation (not spray foam) and to properlly seal any leaks in your HVAC ductwork.
You don’t have to have a multi-tool. A utility knife will work too. Anything that will cut through paint will work. The trim pieces the hold the old window sashes in place are often very old and have layers of paint and sometimes caulk around them and you just need something that will cut through those layers so that you can get them off easier without damaging them. If you’re planning on replacing them, you can just take them off with a pry bar and hammer.