How to repair Ford and Mazda power steering racks

Подписаться 6 тыс.

Просмотров 90 тыс.

50% 1

Learn more here: servicems.eu
In this video we will consider how to repair hydraulic rack FO 209 for Ford Fiesta V, Ford Fusion, Mazda 2. We use the test bench MS502M and special repair tools in the process of diagnostics and repair.
MS502M - servicems.eu/for-diagnostics-...
Special repair tools - servicems.eu/special-repair-t...
Original numbers:
1336686, 1351310, 1351610, 1352973, 2N113200AF, 2N113200CA, 2S613200KF, 2S6C3200KN, 4329684, 4344071, 4356872, 4358909, 4374700, 4386252, 4387041, 4397223, 4452242, 4472936, 4472938, RF2S6C3550KD, VR256C3550, 1667686, 1352976, 1631754, 2S613200MB
______________________
👍Follow us:
- Instagram: / msg_equipment
- Facebook: / msgequipment
- Twitter: / msg_equipment
- Linkedin: / msg-. .
_______________________
If this video helped you out please don't forget to subscribe, give it a thumbs up. Thank you very much for your support!

Авто/Мото

Опубликовано:

6 май 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 30

@MSGEquipment 6 лет назад

More information you can find on the website servicems.eu/for-diagnostics-of-power-steering-system

@cuttheloop Год назад

I just happen to be shy a few (all) of those tools...

@dougwagner5724 4 года назад

So simple, any home mechanic can do it...

@tiny_toilet 3 года назад

My lathe can only do circles - no triangles, so guess I'm outta luck.

@MSGEquipment 3 года назад

It`s just only a fisrt sight.

@skip741x3 Год назад

LOL yeah we all have those fancy tools and lathes dont we?

@paneerselvan8198 3 года назад

Good informative video

@MSGEquipment 3 года назад

Thank you for the feedback!

@InfiniteGamerGaming 3 года назад

How would I fix a rattling noise in my 2005 mkII Ford Focus 1.6 petrol? Noise is on the steering rack

@munyaradziallan9173 4 года назад

is the Mazda 2 steering rack same as the Mazda Demio steering rack

@ebdcauto-technicsconsultin9862 4 года назад

I didn't see adjusting of the pinion pre-load and the final pre-load (rack against pinion) on the yoke side cap nut. The rest all good.

@MSGEquipment 3 года назад

This part was lost during the video prepearing.

@CHEAPROLLIN 2 года назад

My steering used to bind now it has no powersteering at all. It had a new pump put on. Still no power steering. I pulled the steer shaft but it would move great also the pump will bubble every couple minutes when in the air turning wheels..... I used trans tune in pump now. It has a lot of metal flakes in fluid. the vehicle is an 06 ford freestar with no power steering. WIll this rack unclog if I put a little gas in it( I seen this online) if not what do you think my issues could be and any idea how many hours labor or total cost? Please help sorry for novel

@eddyboh2723 8 месяцев назад

One question: I accidentally polished a small segment of the anti-rust zinc coated surface of my steering rack: How do I recover the area I accidentally polished?

@zexzaidi8291 Месяц назад

I assume No grease is needed there.

@reybexn 4 года назад

Is this the same with focus 08my

@prostmahlzeit 11 месяцев назад

What is the part number of the Piston ring at 3:38?

@CHEAPROLLIN 5 месяцев назад

Whats the tool for 4 pin nut

@user-nh4fo7qs2h 11 месяцев назад

Me gusta

@Anthonythesider Год назад

My pre load is leaking on mine

@mdsaiyadkhan9263 3 года назад

Hii

@mdsaiyadkhan9263 3 года назад

Mere ko bhi steering Banane aata hai kahan per hai garage batao

@MSGEquipment 3 года назад

Thank you for the interesting of MSG Equipment. Please contact us - use this form: servicems.eu/contact-us. Or servicems.eu/content/contacts. Our managers let you know about conditions and sheeping for your region

@MrTravisAl Год назад

“Step 13 get help from machining lathe operator.” I wish i were hyperbolizing / exaggerating…. Damn. well that puts a damper (no pun intended) on the plan to rebuild this steering rack and pinion.

@adematthewsracing Год назад

You can do that step with a dremel or a combination of file/hacksaw. I've done all three methods. Lathe is easiest and quickest but not the only way. Of course you only need to do that step if you have worn seals. Most of the time I'm converting these racks to manual so I just cut the whole thing straight off.

@prostmahlzeit 11 месяцев назад

@@adematthewsracinghow do you put that big metal ring back on without a lathe? In the video it looks like they use a new big metal ring that gets compressed on the edge to get fixated on the rack

@adematthewsracing 11 месяцев назад

@@prostmahlzeit Generally I don't put one back on as I convert the racks from PAS to manual so it's not needed. Looks to me as though they're just pushing it on rather than doing any sort of machining on it. You could do the same with a floor mounted press or a drift and hammer especially with a bit of heat.