Wouldn't charge - wouldn't spin. Took some brake parts spray cleaner and hit the charge port and bottom end of corroded capacitor connector. Now works again. Use provided 'straw' to direct spray in charge port otherwise the base finish will come off
Hi lien chen, my is another model but i believe its the same hardware, i charged it on a 220v and it worked, but 2 days later when i was making some juice it worked but when i tested it it just spins for 5 seconds and stop, its not low battery but i just spins and stop after 5 seconds ( it doesnt have any sensor)
Hi My blender has a constant blue light (never goes off) and won't start. I have checked the battery (ok) and motor (connected directly to battery - ok). So I think my voltage regulator/mosfet is also faulty. I don't have a spare one to take from a computer. I need to buy a voltage regulator/mosfet online but how do I choose which one I need? The faulty one I have has 2060K.AE1621 printed on it. Thanks!
Hi Lien Chen, my board is slightly different! It has two batteries, two small MOSFET regulators, and I see two small flat transistors and other ICs! The batteries are charging normally. the motor is spinning if I connect directly to the battery. But the battery power not reaching the motor! The brand is GOCEO-401, 2 X 2200mAH connected in series, 200mL and 200Watts. When I switch on the blue light stays a few seconds and cuts off! The MOSFET X2 looks like SM3116N and the transistor VZ113! Question: 1. Can I use a switch and connect the motor directly to the batteries and off the switch when charging! 2. Where to buy a replacement board? Thanks, Sir! Maha, Malaysia
trace the voltage output of mosfet or you can bypass using switch if you know the connection, but if you can change the 2 mosfet much better, thanks too.. from Taiwan
Hi, I tried bypassing the battery and connecting it directly to a USB power bank or to a 5V charger, sensor light blinks but motor does not start. Do you know a way to bypass the charger altogether to make it work directly with a 5V power source?
try this 3 steps: 1. try to connect the battery directly to motor just to check the motor good or not 2. need to change the mosfet that control the motor and for charging 3. make sure every time you test sensor must near to the magnet which attach to cover of the blender
Yeah, motor is good. It tries to start when powering it directly, but I think the mosfet or a voltage regulator is preventing it to start with 5V. Will try to find a 3 or 4v source. Thanks for replying!
My idea is to emulate what I've seen here in RU-vid with some Bluetooth speakers: Disconnect the battery, attach a USB cable and plug it to a 5V source. But in this case it did not work as expected.
I has the same problem , but mine is dead . The led goes red on charging and turn off after seconds . Nothing else happens. I tried to connect directly to motor it has no problem and battery okay . What do you think is the problem ? Can it be charging regulator. Or something else in the board ? How to know ?
I have the pro plus portable blender for 2 weeks and now the letters CH keep displaying and only spins for a second then stops again..have to wait until the CH letters disappear and will start for another second..is it junk?
Mine won’t charge, try putting the cord in and the charging port fell inside! Open it and see it’s broken off of the board! Looks like that’s going into the bin😢
I bought the portable blender and I used it for few seconds but it couldn’t blend everything though I have charged it more than 3hrs and it will just blend for few seconds and goes off my urself I have not been able to use it, it’s there anyway you can help tell if the blender is bad or good
O meu não tem os imãs. Usei apenas uma vez. Funcionou perfeitamente. Está a mais de dois meses parado. Carreguei totalmente. Nao esta ligando. Quando clico duas vezes, aparece a luz vermelha, depois a azul. E não liga.
@@lienchen12 Mine doesn't have magnets. I only used it once. Worked perfectly. It's been stopped for more than two months. I fully charged. It's not turning on. When I double click, the red light appears, then the blue light. And it doesn't care.