How to Replace Blower Motor 2000-2005 Buick LeSabre

Просмотров 48 тыс.

% 421

Buy Now!
New Heater Blower Motor with Fan Cage from 1AAuto.com 1aau.to/ic/1AHCX00060
This video shows you how to install a blower motor on your 2000-2005 Buick LeSabre. The blower motor, and typically integrated fan, is responsible for blowing the heated or cooled air from your heat or AC system into the cabin of your vehicle. A fan could become noisy if it is broken, or could stop spinning all together.
This process should be similar on the following vehicles:
2000 Buick LeSabre
2001 Buick LeSabre
2002 Buick LeSabre
2003 Buick LeSabre
2004 Buick LeSabre
2005 Buick LeSabre
Tools you will need:
• Phillips Bit in a Ratchet 1aau.to/oa/1AXAA00149
• Phillips Head Screwdriver 1aau.to/oa/1AXAA00013
• Pocket Screwdriver
• 5.5mm socket
• 7mm Socket 1aau.to/oa/1AXAA00017
• Trim Tool Set 1aau.to/oa/1AXXX00006
• Ratchet 1aau.to/oa/1AXAA00016
Subscribe: ru-vid.com/show-UCWCdsftsTqYMO7cA_5Sc-yA
Check out our playlist:
Buick LeSabre 8th Gen 2000-2005: ru-vid.com/group/PLJVpHWuCEUX-MQnh_mAcbDfC3Ft1lP1yt
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

15 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@TRQ 2 года назад

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@wagil90 Год назад

Even though he got the job done like others have said there is an easier way for sure. Remove the panel under the glove box and remove the actual fan out of the housing. I bought the whole assembly but after fighting with the screws in the assembly i just removed the fan out of the assembly. swapped over the L hose to the new fan. reinstalled it. It helps to have a 3rd hand and my kid came in hands

@kevinwells4888 Год назад

I think 2002 - 2005 have a drop out blower motor and the 2000 -2001 have the motor shroud assembly that's shown in this video. I have a 2000 custom that is like this video.

@jacktipton308 2 года назад

Three screws drop blower motor out of ductwork ,saves a ton of struggles

@markletzo1056 2 года назад

In a 2003 Buick Lesabre Custom the motor is silver not a black plastic cover so don’t remove the 5 or 6 screws just remove the 3 brass ones on the silver motor and it comes out easy I don’t even think I would’ve had to remove the carpet and the plastic door plate.

@hale1j 2 года назад

Are the 3 brass 5.5 as well?

@pauld7863 4 месяца назад

For the 2000 LeSabre OEM replacement, orient the blower motor assembly with the electrical connector for the motor facing the passenger side of the car. Insert the fan portion into the duct. Rotate the assembly about 90 deg so that the electrical connector is facing the rear of the vehicle. Push the assembly upward and insert screws.. Applying soapy water to the perimeter of the blower motor assembly and the rubber mat on the floor pan eases insertion. Also helpful, using a big, long screwdriver to push down the rubber mat while rotating and inserting the assembly.

@ericjones4368 Год назад

You don't need to disconnect the negative on the battery your not really dealing with live wire contact

@stevenanderson4941 Год назад

Outstanding video.

@davezupansic8930 7 месяцев назад

Great video!

@logan1nwo 2 года назад

Thanks for the guidance

@moosenuts0062 11 месяцев назад

There are some people saying these steps are incorrect...they are definitely correct IF you have an OEM blower. If it's aftermarket already then you don't need to do all these steps.

@lamontwatts9398 Год назад

Great job

@babycakes8434 Год назад

Great video, I will intend to do it in my 2002 buick lesabre, if it doesn't work, then I will take it to my mechanic. I wonder what safe tool can I use instead of the plastic pry tool that you have, probably screwdriver.

@reggiehowze1891 Год назад

Just what I was looking. Air or heat coming out of vents. Ordered new blend actuators for both sides. Fan comes on but sounds horrible

@danhough3924 Год назад

Good video for step by step but man I was always told not to pull on the wires when trying to remove the connectors but each their own

@calvinc.2333 Год назад

My skin crawls when he pulls the connectors out by the cord

@chiefalots 2 года назад

On a 2004 Le sabre your not near the carpet and there is no spinning because there are plastic tabs in the holes next to the screws. This was tough wish I would have just bought the motor and drop it with 3 screws if you don't need a new plastic cover.

@redbullwang 10 месяцев назад

How did you get this motor in, it feels impossible

@mikeherrmann8874 2 года назад

Very helpful video guys!!!

@bradypyrah9011 Год назад

PLEASE NOTE THAT THE MOTOR BLOWER MAYBE DIFFERENT! IF THE MOTOR YOU HAVE IS DIFFERNT FROM THE ONE IN THE VIDEO, ONLY TAKE OUT THE MOTOR BLOWER!! DO NOT TAKE OUT THR WHOLE THING!! I HAVE SPENT SO MANY HOURS GETTING THIS WHOLE THING TO GET IN AND ALIGN (still haven't gotten it done). The editor needs to adjust something if this isn't the first comment to say only take the motor blower out. Mine didn't NOT look like the one in the video.

@slabbinonspokezz2375 Год назад

Then it's possible you were given the wrong blower motor. Those things do happen speaking from experience as an auto tech.

@michaelsnow7362 2 месяца назад

This is for 2000 like mine and I think 2001. HERE is video for 2002- 2005 (It Wrongly says 2000- 20005)

@ronalddoyle3158 Год назад

He makes it look easy. IT IS NOT!! I just finished my car putting this in. A tip, for the readers is, my hands and fingers are too fat to put the screws back in, put your screw back in the socket of your tool and use electrical tape to keep it in the socket, then you can screw it back in the hole without losing the screw.

@ks_hunter7327 9 месяцев назад

TRQ you should sell the two part style instead. It is SO MUCH easier to install. The motor unbolts from the housing. It took me 5 minutes to install the new fan, until the OEM style the was clearly repaired friendly.

@TRQ 9 месяцев назад

+@ks_hunter7327 Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

@daytonaboy5832 Год назад

Can u use a different one that fits

@chick5958 Год назад

i for the life of me cant get the little black box with the wiring clips OUT OF THE WAY ive tried everyday for a week what am i doing wrong

@brendacraver4441 Год назад

What if the fan blades disappear when you turn the ac on?

@chrisjohn7395 Год назад

How do you know if your blower motor is bad?

@kennethgarver5791 3 месяца назад

Where is resistor located on a 2003

@JBaldwin2001 3 дня назад

I like how you cut the video three times while putting it back in. Wasn’t very helpful.

@garyvoit5451 Год назад

U must've forgot a step cuz I did what u did and don't see the Blower motor

@Bluelt1 5 месяцев назад

Why in the world a 5.5mm bolt? Come on GM!

@jefflaplante4834 10 месяцев назад

I did this process after removing saw I could of just removed 3 bolts for the blower motor why remove the bracket only thing I can think of is to charge your customers more money shame on you