How To Replace Front Air Suspension Shock on Mercedes | Arnott Struts for CLS-Class W219

Подписаться 328 тыс.

Просмотров 169 тыс.

50% 1

CLS55 Suspension Shock Change | How To Replace Front Air Suspension Shock on CLS55 Mercedes | Arnott Struts for CLS-Class W219 | E-Class W211
#HarjinderSidhu #MercedesAirSuspension #MercedesStruts #SidhuDIY #easystepsdoggies
🙏 Shop online at Amazon - www.amazon.com...
Any Amazon Link in my description is an affiliate link. “As an Amazon Associate, I earn from qualifying purchases.” I would greatly appreciate it if you considered supporting my channel while shopping from the Amazon store by buying anything you needed from Amazon after clicking on one of the links. This gives me a small commission at no additional cost to you and helps me continue producing more videos! Thanks a million for your support!!🙏
Arnott AS-2788 Front Air Struts for the '03-'09 Mercedes-Benz E-Class AMG and '05-'11 CLS-Class AMG - amzn.to/2lptCXC
Metric 1/4 and 3/8 Drive Socket Set, 40 Piece - amzn.to/2kMvJak
TEKTON 13101 3/8-Inch Drive Socket Set, Inch/Metric, 6-Point, 5/16-Inch - 3/4-Inch, 8 mm - 19 mm, 45-Piece - amzn.to/2lmTbrz
Stanley STMT71654 201-Piece Mechanics Tool Set - amzn.to/2kRJDrs
DEWALT DWMT75049 Mechanics Tools Set (192 Piece) - amzn.to/2lpw14y
4 Way Cross Lug Nut Wrench - amzn.to/2lmLD8f
Heavy Duty Wheel Chocks - amzn.to/2qpRegc
Torin T83006 SUV Service Jack - 3 Ton - amzn.to/2kRJQee
Curved Jaw Locking Pliers - amzn.to/2kRAyyP
*********************************************************
desertfrog • Thanks for providing the info. 08/19/2020
Torque specs:
- Top mounting nuts: 30 Nm
- Air pressure line: 2 Nm
- Upper control arm: (stage 1) 20 Nm then (stage 2) 90 degrees
- Strut to spring control arm: 165 Nm
*********************************************************
Thanks for watching, Enjoy, and please don't forget to: LIKE, COMMENT, FAVORITE, SHARE and SUBSCRIBE. ”GIVE THIS VIDEO A THUMBS UP"
Please SUBSCRIBE, If you haven't done so yet, take a look around. If you like what you see be sure to Subscribe to be notified when new content is posted. Thanks again for visiting!
Easy Steps - easysteps.jimdo...
{This video is for educational purposes only, I am NOT a "Professional Licensed/Certified Mechanic" or "Professional Licensed/Certified Technician" and I am not liable/Responsible in any way for damages caused to YOU or your "Vehicle" or "Computer/Phone" due to this video}. Please leave your comments below if you have any questions or concerns. Hope this helps someone out there. Cheers!
*Disclaimer - Background Music "Alan Walker - Fade" (NCS Release)
**Disclaimer: All information is for educational purposes only and is the personal view of the author.

Опубликовано:

12 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 228

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@19lol19 7 лет назад

nice video boss. please keep them coming us Benz drivers need someone like you to help us out..

@brian662901 6 лет назад

Tay Lindsey what you said im about to get my hands dirty

@YouTube.TOM.A 5 лет назад

Easy Steps. To my friends at easy steps. I did my job yesterday and i followed your method. Very happy results; thank you. I have 3 busted shocks in my garage and i waned to cover a few things. If you are buying air shocks from a auto salvage yard, which i sometimes do. Make sure the bottom of the shock is not loose. nothing good will happen if the shock is sloppy in fit below before installation. Once you have installed the shock always remember to keep the right front wheel on asphalt. if you pull of the highway [ road ] on the shoulder pick your spots. In the Mercedes [ CLS S500 E500 and others ] the lower control arm are a bear claw knuckle [ very strong ] but if the bushings are worn a lot of lateral force will be exerted on the base of the shock and that can cause ruptures and / or leaks; i also have to admit that i blew mine out going over a crappy railroad crossing at too high a speed. thank you for shearing.

@EasySteps_Sidhu 5 лет назад

Thank you so much for the like, glad to help. Thank you so much for the like and thanks for watching. Thanks for taking your time and sharing great info. it really makes my day.

@EasySteps_Sidhu 5 лет назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. ru-vid.com

@kittypigeonclueless5566 6 лет назад

Magnificent video!!!!! I cannot fathom why 14 people would not like it. I am thirty minutes away from replacing the air suspension on my cls55 with coil overs and it was great to be able to see you do this for some peace of mind. Congrats and keep up the great videos!! P.S. That's one great car you have there!

@trentdawg2832 2 года назад

Hell yeah this just brought my anxiety level WAY down….earlier today my passenger side front went out…….I already ordered the part from summit so it will be here in 2 days then I can go outside and perform surgery with ease……thank you my friend my cls550 appreciates you!!!!

@EasySteps_Sidhu 2 года назад

Glad I could help! Most welcome 😃 Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

@Loujr2250 Месяц назад

My favorite video yet, my only question is, did you have to depressurize the system before taking out the strut and before installing the new one?

@EasySteps_Sidhu Месяц назад

Thank you for liking my video. I showed in the video that the shock was leaking and flat compared to the other side.

@ersweene 2 года назад

Did this job last night and it took me about 3.5 hours going slow to do it. A couple of tips, I had to smack the upper ball joint very hard 4-5x with a heavy hammer to pop that ball joint out. Also, had a tough time getting the bottom screw back in through the hole of the replacement shock. Had to use a wedge to keep the lower control arm down a bit and really lean hard down on the caliper to line up the hole so the screw would slide in. Probably the hardest part of the job was that. All is good now, thanks a bunch for the video. It was super helpful!!

@EasySteps_Sidhu 2 года назад

Thanks for sharing the info. Glad to help. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

@poppaandpuff 6 лет назад

Great video that gave me the confidence to tackle my W211 wagon front left strut. I just want to add a few notes on top of this. 1) This job took me 3.5 hours with the help of one other person. It may only take an hour for a good backyard mech but for us norms, block off the morning 2) The hammer trick on the ball joint did not work for me. Have a ball joint popper available 3) The dead front strut did not wiggle out as easily as shown here. Maybe it's the W211 chassis vs the W219. Either way, I got around this by compressing the strut with a ratchet strap and then pulling it out 4) Since the replacement comes fully pressurized, you won't be able to reverse the process without deflating it. To do this I got two of the top bolts in and then hooked up the top electrical connection. From there I turned the car on and lifted/lowered the car 10 or so times. You'll hear the air releasing and the bellow will get soft. From there I undid the nuts, compressed with the ratchet strap and then put it back in Thanks again for putting this up. Hopefully my notes help the next person to tackle their dead airstrut

@xkrnxboix 5 лет назад

Does this arnott suspension retain the oem suspension adjustments? so can you still change suspension setting using the button?

@henrylong45 5 лет назад

Best Air Shock to Air Shock replacement video on RU-vid. This one is EXCELLENT!

@henrylong45 5 лет назад

I have a 2006 CLS500. You used an Arnot shock in this video. Why Arnot? Do you know anything about the Dorman brand of shock which is quite a bit less expensive?

@samln5019 Год назад

This video was very helpful with my 2006. Thanks for posting and great tutorial. Saved about $800 bucks.

@EasySteps_Sidhu Год назад

You're welcome! Glad I could help. 🙏 Thanks for the visit. Thanks for the like and thanks for watching.🙏

@samln5019 Год назад

@@EasySteps_Sidhu oh Totally!!, only thing, I had to get the ball joint separator tool, highly recommend it though, $35 bucks auto zone, and can return it, fully refundable.

@EasySteps_Sidhu Год назад

@@samln5019 Good point, Thanks for sharing the info.

@lnkinc6823 Год назад

Thank you so much for the video very informative and detailed I do have a question when one of the besides go bad is it required to get all four or a set of two or can you just fix the one thank you again for the video

@EasySteps_Sidhu 11 месяцев назад

Please don't fix them if they are not broken. Most welcome 😊Glad I could help. 🙏 Thanks for the like and thanks for watching.🙏

@desertfrog 4 года назад

Torque specs: - Top mounting nuts: 30 Nm - Air pressure line: 2 Nm - Upper control arm: (stage 1) 20 Nm then (stage 2) 90 degrees - Strut to spring control arm: 165 Nm

@EasySteps_Sidhu 4 года назад

Thanks for sharing the info. I have added in the description.👍 Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@desertfrog 4 года назад

@@EasySteps_Sidhu I believe the spring control arm has to be tightened to specifications when the car is on the ground. If doing this DIY you want an alignment after the job, you can ask them to loosen and re-tighten the bolt as needed. I am getting ready to do this job this weekend on my E63 wagon. You indicate a mix of metric and imperial units. I would assume that it would be all metric. Is the 13/16 spring control arm really 20 mm?

@pierombon 5 лет назад

Thank you !!! Very clear and extremely helpful learning video. I just took the Strut out . Now fit the new one.

@EasySteps_Sidhu 4 года назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@markkostelic485 Год назад

I think you meant to say "Fender Liner" instead of "Fender Line". Good explanation. thanks

@EasySteps_Sidhu Год назад

You are welcome. Glad it helped. Yes..." Fender Liner". Thanks for the like and thanks for watching.🙏

@theexclusivelegacy 9 месяцев назад

Thank you! 💪🏾 Saving people thousands of dollars 🙏🏾

@EasySteps_Sidhu 9 месяцев назад

You are most welcome. Glad to help, thanks for the like, and thanks for watching. You have a blessed day.🙏

@YouTube.TOM.A 5 лет назад

Very helpful video. Airmatic is a beautiful system. With ABC [ active body control ] you have the advantage of fluid leaks [ PENTOSIN ] indicating the failed components but with air leaks it is not so evident; and one leaking strut can cause a variation of symptoms, sometimes its better to change both fronts at the same time. the rear suspension has a much longer service life.

@EasySteps_Sidhu 5 лет назад

Thank you so much for the like, glad to help. Thanks for taking your time and sharing great info. it really makes my day. Thank you so much for the like and thanks for watching.

@davejohnson3860 5 лет назад

Oh wow, you hit the nail on the head...Mine did the exact same when I jacked it up the air was leaving! Now I'm sold its my air strut! Nice video

@EasySteps_Sidhu 5 лет назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@alphageneration66 7 лет назад

After you install another strut do you need any kind of programming so it makes the psi as on the other struts?

@richarddejarnatt9212 2 года назад

No, there is a level sensor that takes care of adjusting the height.

@ricpri89 3 года назад

Very simple understandable installation video - one of the best I've seen - keep em coming - my 1st w211

@EasySteps_Sidhu 3 года назад

Awesome, thank you!😅, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@lexbrettgen2120 7 лет назад

Brilliant video thank you so much. The tutorial gave me the confidence to tackle the job myself. I bought two airstruts for about $1000 and installed myself (Arnot Remanufactured with Lifetime warranty). The quote at Merchants Tire and Auto was $2500 (for the same struts). I had to chuckle a bit when you said the whole process took about an hour. At least not for me.. Just getting off the locking nut from the upper control arm took a while to figure out, and I ended up buying a special tool, no big deal. Also I noticed that used a 17mm socket, but the locking nut on my vehicle was about a SAE 5/8". Perhaps my w219 is a bit different (cls500, 2006, non-amg)? I also couldn't get the suspension to level until after I raised the vehicle (with the button) and let it go back down again. But finally the car leveled which brought Please consider making a video for the rear air struts!! It's not clear whether or not the rear need STAR reprogramming to level, which would make it a PITA for a DIY..

@JusKeef 5 месяцев назад

Amazing video! Thx so much!

@EasySteps_Sidhu 5 месяцев назад

Glad you liked it! Thanks! 😃

@davidc9985 4 года назад

Thanks for such great detailed videos!!! These videos keep me riding in a beautiful Benz because with them I can do all my own work!!

@EasySteps_Sidhu 4 года назад

You are most welcome, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@samsharif8955 4 года назад

Good job

@superb63amg94 2 года назад

You just saved me thousands of dollars. Thanks bro. Well appreciated!!!👍🏼

@EasySteps_Sidhu 2 года назад

Glad I could help...You are most welcome. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

@lcervantes8505 2 года назад

Great video. Is the electrical connector is one piece from bottom to top, why disconnect from both top and bottom points?

@EasySteps_Sidhu 2 года назад

Great to hear! Glad I could help! please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

@markkostelic485 Год назад

I had no luck hammering the ball joint to free it. Bought the separator tool, but placed it correctly as to not damage the ball joint rubber.

@EasySteps_Sidhu Год назад

Thanks for sharing the info. I know it's hard but can be done as you have seen in the video. 🙏 Glad it helped! 🙏 thanks for the visit. Thanks for the like and thanks for watching.🙏

@damon657 4 года назад

Did you disconnect the battery first? And what did you do about the new pressurized strut to shrink it and get it in? Thank you

@EasySteps_Sidhu 4 года назад

Yes, please disconnect the negative terminal. The strut, please do exactly as I have shown in the video press the rotor assembly down and then it will fit easily. I hope it helps, thanks for watching. Good luck with your DIY project.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@Leightyluiz 4 месяца назад

Thank you

@EasySteps_Sidhu 4 месяца назад

You're welcome. I'm glad I could help. Thanks for watching my video.

@rjack987 5 лет назад

Good tip on NOT using a ball joint remover on the upper control arm. excellent video!

@EasySteps_Sidhu 5 лет назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 5 лет назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. ru-vid.com

@Alan.BigAl. 6 лет назад

Very clear and extremely helpful. Thanks for taking the time to post. Alan

@rh9625 6 лет назад

Great video!! Not sure if you stated this, but the new strut comes under pressure. In order to release the air disconnect the negative connection on your battery and place the new strut in your engine compartment. Connect the electrical connection. Now reconnect and disconnect your battery connection about 16 times. You will will hear the air releasing from the strut. This will allow you to use the crowbar to compress the strut enough to slide it into place over the control arm. I used a small 18 inch crowbar, which worked perfectly. I did both both pair of my front struts.

@paulheiner5347 4 года назад

Thanks mate easy job after watching your video saved me a small fortune your a legend

@EasySteps_Sidhu 4 года назад

Glad it helped. Great to hear!👍👍. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@ahmadtalsaadi 6 лет назад

thanks for this video, really helpful. thumb up! I noticed that you uploaded video for the rear AS for merc, that what I am looking for :) do you have video showing how to replace the rear AC for CLS? thank you in advance.

@MrAnwazi007 6 лет назад

Do you know if the w218 is similar 2012 cls 550 4matic? Also, do you know the torque specs on the bolts. Great video!

@bradbobbitt9244 7 лет назад

-Great video, I found this just as I was about to replace mine on my 2006 IWC edition. Just wanted to add that I always use a jack stand under the car to back up my jack .

@21DannyC 6 лет назад

Hey man great video. I had a few questions I would like to ask you in regards to my 2012 CLS 550. I was told I need to replace the left and right rear air suspension strut. This part is said to be covered under my CPO extended warranty. However, I am being told that it isn’t covered bc it’s not a part not in fact covered. Am I being given the run around or could this be true? Not sure how many parts go in to the suspension. Thought it was the actual air bag and strut. Could use your expertise. Thanks.

@williamcallahanlll2924 5 лет назад

21DannyC lol wow I just had mine done , last week. 2k parts & labor for 2012 cls550, both bags. Have noticed alittle sagging still, not much though. Was told to too winter cold temps. ??

@colinaglae2605 6 лет назад

Brilliant video......very informative. Looking forward to a front lower ball joint replacement one in detail.

@nausherx 6 лет назад

Hi, I have couple of questions with regards to the process. 1. Did you have to disconnect the battery before starting the replacement? 2. With the Arnott strut, as I understand it is already pressurized, did that cause a problem when fitting in? I read some forums where they said to decompress the strut and take the air out (using 5v batteries connected to the upper connection points of the strut) - did you need to do any of that? 3. Once installed did you need to use a STAR system in order for the car to align itself with the correct pressure on all 4 tires? I am planning to do my replacement tomorrow so if you could respond at the earliest I would appreciate it (this is for a W211 E55)

@designcoordinates2981 4 года назад

A couple of things: 1- New or used struts are under pressure, you cannot install them easily unless you release the pressure (connect the top plug lock and unlock car a few times OR use 9v battery and supply that to the top connector. 2- Raising both sides of the car makes it easy to uninstall the old strut you wont have to push the whole wheel hub down 3- Tightening the ball joint of upper control arm, you need to hold the bolt while you tighten the nut (there is a hole in it for hex bit)

@EasySteps_Sidhu 4 года назад

Thanks for sharing the info. and thanks for watching.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@mrmykd 5 лет назад

Thank you for this video I will be doing this job tomorrow

@EasySteps_Sidhu 5 лет назад

You are most welcome, glad to help. Good luck with your DIY project. Thank you so much for the like and thanks for watching.

@harrisonmandell3600 3 года назад

Great video, made this project a breeze. Thank you.

@EasySteps_Sidhu 3 года назад

So nice of you. You are most welcome😅, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@REAL_MPSS 6 лет назад

Well done. I’m going to keep my E500 now! Thanks.

@michaelfinley4433 4 года назад

Same here...

@romeo4002 6 лет назад

This video really helps!!! I have a question, is this same for all MB vehicles? I have a GL550 SUV that probly need too change the air suspension... thanks!!

@frank431 4 года назад

Wow, I did it! And I thank you, Sidhu for your great video showing concise step by step instructions, giving me the confidence I needed. You can imagine my trepidation to do a job like this on my 2008 CLS 550, that I bought new and paid cash for. Especially since I paid my dealer $2,000 to change the other shock a few years ago. This time it was just the cost of the part (and a few Tylenol for my aching muscles). The steps were as straightforward as you said. Great job!

@EasySteps_Sidhu 4 года назад

You are most welcome my friend, thanks for sharing great feedback, thanks again for taking your time and sharing your experience and it really gives me immense pleasure and makes my day. Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@ronbourassa353 6 лет назад

Replaced mine today. Ball joint had me stumped. Video helped and car is good. HOWEVER...I should read about installing the new air line. TIP: Remove old fitting from air line leaving new fitting in NEW strut and just push line in.

@colinaglae2605 6 лет назад

Kindly advise if there is enough space to use a air tool to undo the bolt & nut off the control arm!! It can be quite stubborn.

@superprojb 3 года назад

Best detail video yet. Thanks.

@EasySteps_Sidhu 3 года назад

You are so welcome! Glad you liked it! 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@ceezauto213 3 года назад

Great video, does this also apply to a 2010 Mercedes-Benz E550?

@autotechnik665 3 года назад

Super video. It helped me a lot. Thanks and good luck !

@EasySteps_Sidhu 3 года назад

You're welcome! Glad you liked it! 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@kaleihoopai7332 7 лет назад

Cool Thanks Dude. I got a 211. How long does it take to switch out. Hours wise?

@scartermusictx 7 лет назад

When you do this, do you unplug the electrical on the brakes as well? So as to not tear Those lines?

@YouTube.TOM.A 5 лет назад

Not Needed!! since there is enough room and line length to do the repair comfortably.

@gkelly941 3 года назад

Another way to separate the ball joint is to rent a hinged ball joint separation tool at Auto Zone, and use it to separate the ball joint without damaging the rubber boot. If you don't remove the loosened nut, the suspension won't fly apart when the ball joint separates. If you return the tool within the time limit, you get your money back!

@EasySteps_Sidhu 3 года назад

Glad to hear that! You’re welcome 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@26glockster 7 лет назад

how much of a space is there supposed to be between the control arm and tire? my sister has a cls 550 and says it's normal to be slightly rubbing the tire

@maxowndhard 6 лет назад

can you just lift it up as a normal car? or does the cls have a liftmode or something

@mahandmalcolm3472 5 лет назад

Hey bro are the driver side and passenger side sucks the same? Great Video 📹 BTW

@EasySteps_Sidhu 4 года назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@TruTuning 6 лет назад

You didnt have to disconnect the air compressor relay or deactivate it?

@rickydavis4964 2 года назад

Nice work. I think the bolts are all metric though being from Germany. Don't want to strip anything.

@EasySteps_Sidhu 2 года назад

😊 glad to help. Thank you so much for the like and thanks for watching.🙏

@EasySteps_Sidhu 2 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@evolutionsimplified 4 года назад

Brother bless you for this

@EasySteps_Sidhu 4 года назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 ru-vid.com

@mazharsoufi5270 4 года назад

thanks man so nice of you!!!!!!

@EasySteps_Sidhu 4 года назад

You are most welcome. Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 ru-vid.com

@StarWarNerd 6 лет назад

Is there a way to test the air line to make sure air going through?

@iam_ChrisJHarris 4 года назад

I have a 2009 Cls 550 recently the battery died due to the lights been left on over night. I got the car started but now I have a suspension malfunction light on the dash. And the car is sitting low in the front. Do I need to replace the suspension now?

@EasySteps_Sidhu 4 года назад

Hi Chris, it can be three things. First, did your cls550 used to sit low in the front before the battery issue? If so, then yes you definitely have a bad suspension bag. Two, if it did not use to fall down before, then possibly your ride height sensor has gone bad (these control the height of the suspension) and when the car falls down, sometimes these go bad. Three, it can be that your battery has drained and is not at full capacity anymore, Mercedes are very sensitive to battery voltages and need the most optimal voltage to run correctly.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@aceburly 5 лет назад

Can you make one for the rear left or rear in general

@EasySteps_Sidhu 5 лет назад

Thanks for asking, I have added to my to-do list. Thank you so much for the like and thanks for watching, I always do answer to my viewers for their every question. Unfortunately, my account got hacked and this hacker has deleted all my comments from 1800 + videos. I am posting a thanks message to my viewers/subscribers for their support. My RU-vid channel was hacked/hijacked on (4/24/2019) and I got it back now (5/5/2019). The hacker has deleted the information under the description of my videos as well as all my comments. My RU-vid Account Got Hacked - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1xLEciPJqlk.html

@EasySteps_Sidhu 5 лет назад

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. ru-vid.com/show-UCuifMS69Pmx-ykxCar5XW6Q

@xaviersantiago3214 7 лет назад

did you disconnect the battery or relay?

@michaelpineda4535 4 года назад

I want to install an aftermarket air ride and use accuair management but can't find the suspension unit. Do you know where I can find them?

@EasySteps_Sidhu 4 года назад

I have listed the online Amazon links under the description, please check it out. Good luck with your DIY project, thanks for watching.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@papilat1 7 лет назад

it is very nice video very helpfull

@david_gloria4_pb 3 года назад

Will this work on a 2005 mercedes e500 4matic

@diablocls55 2 года назад

About to do this on my CLS55

@EasySteps_Sidhu 2 года назад

Glad I could help! please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

@steveswell1 5 лет назад

Great video!

@EasySteps_Sidhu 5 лет назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 5 лет назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. ru-vid.com

@Daniel-qc9vw 6 лет назад

do you know how to change the dust cover?

@jayse63amg31 5 лет назад

Thank you!!! This is very helpful...

@jayse63amg31 5 лет назад

you got another subscriber sir 👍🏻

@se46m3an 7 лет назад

Torque specs?

@Themayseffect 5 лет назад

dude he did this in his driveway lmao.

@AKLINTMURT 4 года назад

nice video thanks !

@EasySteps_Sidhu 4 года назад

Glad you liked it! Most welcome👍, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@AKLINTMURT 4 года назад

@@EasySteps_Sidhu + my subscribe !

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@AKLINTMURT 4 года назад

@@EasySteps_Sidhu ok i see this right now

@kaibintech 3 года назад

Thanks. Nice video!

@colinaglae2605 7 лет назад

Thanx buddy. Nice video.

@Mel-eo1xe 5 лет назад

Nice job

@EasySteps_Sidhu 5 лет назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@Chris_Styles 7 лет назад

Amazing! Thanks for sharing

@fristtime4983 2 года назад

Ian replacing the left airstrut I am having a problem getting the shock to move up to get the lower bolt in any help 08mercebes cls550 w219

@tommyestridge9301 7 лет назад

You should give the torque settings for all the bolts.

@ninjamigs1766 4 года назад

M&m in this case means MILLIMETER...

@EasySteps_Sidhu 4 года назад

Yes, sir, it means millimeter. Thanks for watching it.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. ru-vid.com

@xkrnxboix 5 лет назад

Anyone with a w211 e55... Does this arnott suspension retain the oem suspension adjustments? so can you still change suspension setting using the button?

@kaibintech 4 года назад

nice video!

@EasySteps_Sidhu 4 года назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 ru-vid.com

@samuelito1130 7 лет назад

excellent video 👍

@1AEROSOL.1PUFF 4 года назад

Two tips, one, remove bracelet, two, spray all ball joints with silicon, otherwise great job.

@EasySteps_Sidhu 4 года назад

Great point!Happy to help 😊😊 Cheers! Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please like, share and subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@fristtime4983 2 года назад

Look at your video and I'll order both air struts pass and driver ,be here in a week I'll let u know how I made out

@drracer1719 3 года назад

Thank you ...

@Sclassmercedes 6 лет назад

So you’re telling me that the cls Amg doesn’t have active body control ? I thought the cls would have the abc system . I wish my s55 have the airmatic instead of the abc .

@YouTube.TOM.A 5 лет назад

As far a i know [ ABC ] Active body control is a trade name that Mercedes Benz has used for the fluid operated suspension installed in several of their models. sometimes older models [ versions ] of the same car example S55 had ABC

@abensonmpa 7 лет назад

Thank you for this video. I have my part, and I will try this tomorrow

@abensonmpa 7 лет назад

Absolutely! !! At it right now. Ball joint popped. Having issues with the 13/16...should be easy fix once my buddy gets here. Thanks again

@abensonmpa 7 лет назад

All done...thanks to you my w211 is back to normal

@rexhkumanova8921 7 лет назад

hey man was it hard?

@rexhkumanova8921 7 лет назад

thank u man ur saving us money god bless u

@abensonmpa 7 лет назад

Rexh Kumanova, not hard at all...should take you about an hour...and I am not good with cars...

@boyka9115 7 лет назад

Good Job bro 😍

@EricEvolving 5 лет назад

I need to do this to my 2008 CLS...

@EasySteps_Sidhu 5 лет назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 5 лет назад

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. ru-vid.com/show-UCuifMS69Pmx-ykxCar5XW6Q

@ducatilove11 5 лет назад

I spent $350 on labor for the left side only.. good video bro!!

@WicKedwiNd91 5 лет назад

Alden Palencia did they at least lube you up?

@sergeytm4474 4 года назад

big bossss👉💪

@EasySteps_Sidhu 4 года назад

Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@sergeytm4474 4 года назад

@@EasySteps_Sidhu ok thanks!

@EasySteps_Sidhu 4 года назад

🙌 🙏 🙌

@carltoncrowder2717 3 года назад

Watch your video cls 550 right air strut is not going in what else can be done

@EasySteps_Sidhu 3 года назад

do you mean it's hitting the rotor, if it is then press with your feet and ask a second person to slide the strut in? Hope it helps, thanks for watching.

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@tyram3084 9 месяцев назад

Is this the same for a CLS 5550 I'd rather do it myself then take it the shop for 2200 😂

@EasySteps_Sidhu 9 месяцев назад

I do have a video posted for - How To Replace Front Air Suspension Shock on CLS550 Mercedes | Struts for CLS-Class Mercedes W218 - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Hj2xh33lyTQ.html Please share the results, thanks for watching.🙏

@tyram3084 9 месяцев назад

@@EasySteps_Sidhu hell yeah thank u sir🤘

@EasySteps_Sidhu 9 месяцев назад

You are most welcome, good luck with your DIY project.👍

@tyram3084 9 месяцев назад

An one more question cuz Im putting coil overs instead of air bag I just disconnect air ride an should be good to go??

@charlesallen1874 9 месяцев назад

Doesn’t work on cls55. The sway bar has to be disconnected from the control arm.

@rap_freestyles 6 месяцев назад

No it doesn’t, just disconnect the ball joint first before doing the strut bolt and it will drop enough to access the strut bolt.

@nattyp7801 Год назад

My first time replacing the front air strut,👁damaged the axle 😢😢

@EasySteps_Sidhu Год назад

what you do wrong? how it got damaged?

@nattyp7801 Год назад

@@EasySteps_Sidhu 😁😁😁putting too much pressure on it,to remove the air strut,first time 🥴🥴

@EasySteps_Sidhu Год назад

oh no...😢

@antreassolomou8419 4 года назад

hello guys how I know if my w211 if I got front air struts or front air springs?

@EasySteps_Sidhu 4 года назад

Both are the same thing.

@antreassolomou8419 4 года назад

@@EasySteps_Sidhu my w211 is down all four wheels when I start the car I can hear the air compressor turning on but after a few seconds shuts down..any idea?

@EasySteps_Sidhu 4 года назад

your air compressor is most likely going bad.

@EasySteps_Sidhu 4 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 ru-vid.com

@antreassolomou8419 4 года назад

@@EasySteps_Sidhu for sure I know I got a rear leak on the rear air bags isit a chance my compressor stops because of the leak?

@81deaths 6 лет назад

Dope

@laszlogaspar1244 3 года назад

New

@EasySteps_Sidhu 3 года назад

Thanks for watching.

@EasySteps_Sidhu 3 года назад

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 ru-vid.com

@benzzmedia1135 7 лет назад

2:17

@PreetSingh-ji7ey 5 лет назад

Nice paji Benz ripped my bund on this repair

@EasySteps_Sidhu 5 лет назад

hahahaha... Start doing DIY and save money. Thanks, glad to help. Thank you so much for the like and thanks for watching.

@EasySteps_Sidhu 5 лет назад

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. ru-vid.com