No video :(

How to Replace Front CV Axle 96-04 Nissan Pathfinder

Подписаться 498 тыс.

Просмотров 58 тыс.

50% 1

Buy Now!
New CV Axle Shaft Set from 1AAuto.com 1aau.to/ia/1AAC...
This video shows you how to install a new TRQ CV axle on your 96-04 Nissan Pathfinder. Head over to TRQAutoparts.com for more info!
• Check here for more videos on the 1996-2004 Nissan pathfinder: • Nissan Pathfinder 1996...
This process should be similar on the following vehicles:
1996 Nissan Pathfinder
1997 Nissan Pathfinder
1998 Nissan Pathfinder
1999 Nissan Pathfinder
2000 Nissan Pathfinder
2001 Nissan Pathfinder
2002 Nissan Pathfinder
2003 Nissan Pathfinder
2004 Nissan Pathfinder
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 17mm Wrench 1aau.to/oa/1AXA...
• 10mm Socket 1aau.to/oa/1AXA...
• 12mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• 22mm Socket 1aau.to/oa/1AXA...
• Snap Ring Pliers
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Block of Wood
• Brake Grease
• Cloth Rags 1aau.to/oa/1AXS...
• Liquid Thread Locker
• Center Punch 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Nissan Pathfinder 1996-2004 Second Gen: • Nissan Pathfinder 1996...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

22 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 57

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@fritzthecat9451 3 года назад

I didnt know there was any other way?

@davehtown 3 года назад

This is the type of video you dream of when doing a repair you’ve never done before. Great video!

@TRQ 3 года назад

+N20- VQ Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@jasonshaw4820 3 года назад

Mate,one of the best how to's ive even seen.A1.Excellent

@jonathanspecht7671 3 года назад

I wish all auto repair videos could be this clear and concise.

@TRQ 3 года назад

+Jonathan Specht Thanks for watching our video! 1aau.to/m/Shop-TRQ

@w23342 4 года назад

Thanks for taking the time to do the video. It was incredibly helpful

@taberwit 3 года назад

Just did the passenger side tonight. This video was PERFECT! Thank you!

@TRQ 3 года назад

+tbharkerII Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@johndesimone3663 3 года назад

I watched your video and changed my own cv joint after watching your video. I just want to say it really helped you were right on the money brother. Thanks again you saved me lots of cash great video well made.

@TRQ 3 года назад

+John Desimone Thanks for watching our video! 1aau.to/m/Shop-TRQ

@damohart6909 2 года назад

That was a really excellent video. I need to do this soon (just discovered the CV in my Pathy is gone) and I couldn't think of a better instructional for how to do it. Thank you so much!

@dialysistechtipstricks8634 3 года назад

Beautiful work! It's also a perfect time to replace the struts!

@Industrial_Mechanic 4 года назад

Perfect instructions. I think it's the same for my 2002 infiniti Qx4. I am going to do this soon. Thank you for the video.

@saal202 3 года назад

Excellent video, clear explanation, great camera work. Gracias!

@jordanbarnett7247 25 дней назад

Damn I need this for the 1990-95 pathfinders lol. Not one video on RU-vid for the older models

@williamzwit4308 21 день назад

The strut clamp bolts will come out or install easier when the holes are lined up. He shows here all the misalignment is lined up quite easily with the floor Jack manipulating the knuckle this way or that way.

@anthonysanders9211 3 года назад

Was perfect instructions. I replaced mine today. Thank you.

@TRQ 3 года назад

+Anthony Sanders Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@billgregory9560 2 года назад

great video I have a qx4 that Im bringing back to life , I hope i can find more of your videos on the nissan vehicle thank you

@kevineldridge7861 Год назад

Awesome video! Made my project very simple.

@ecuonocustela Год назад

Thanks from Brazil!

@earfman7527 4 года назад

Excellent video

@Ty-tie_FTW 2 месяца назад

Any idea why gear oil would come out at the differential side when I remove the axle from it? That looks like it should all be sealed

@prognozprognoz9145 Месяц назад

How difficult is it to remove the ABS ring on the R50 axles? I accidentally ordered axles without the ring and my R50 has ABS. Hoping I can swap them easily.

@olivi3339 2 года назад

How come nobody ever re-greases the needle bearing inside the knuckle??.. That's what the axle shaft is spinning on... It's so easy to do it , when the axle is out.... It also has 200,000 miles on it...... unless you've installed manual locking hubs, those front shafts are spinning all the time while driving...

@jonathanhankins790 3 месяца назад

Would this application instructions work also on a 95 hardbody v6 ? Cant find any other videos for the trucks.

@Tuker1954 2 месяца назад

Just did this repair as my pathfinder has a slight vibration when driving but only at around 60km/h and it also has a slight knocking sound when you roll forward slowly from a stop and don’t give it any throttle. The new CV axles made it quieter but the noise and vibration is still there. Could I be looking at a potential issue in my front differential? Maybe transfer case? I’ve ordered oil for both of them and I’ll be giving them both fresh oil, hoping that solves my problem but besides wheel bearings I’m not sure where else to look. Any advice?

@cataobo5080 Год назад

Excelent job !

@chrisreyes-ts7yp Год назад

After retightening , the six bolts, when car lift it up in the air at 33ln. would I be required to do it again when full suspension is on the ground.

@laeertejose1913 2 дня назад

Bom tarde você sabe min dizer quando dentis tem o eixo da trizeta da Nissan patfaider 1999 motor V6 3.3

@spartan117613 2 года назад

Hello I own a nissan terrano 1 from 1990 is that the change of gimbal is the same as that of the video? Thank you

@mboytek 3 года назад

Great video! Thanks for making this.

@waterboxer87 3 года назад

Excellent video.

@fritzthecat9451 3 года назад

Wouldn't it be advantageous to replace the bearings also?

@josesolis5616 3 года назад

I have a torn cv boot on a 97 I just bought. New cv axle on passenger side with torn boot less than 10k miles on it. Called Nissan and quoted me 700 just to replace the boot, I know you have to take it all apart anyways. 700 seems way too steep for the amount of labor it takes. I’m not a mechanic but it doesn’t seem like it should cost that much. Am I right or wrong?

@jeffreyganley9776 3 года назад

Excellent video thankyou

@austinmort5300 3 года назад

What size O-ring on the bearing?

@jhruizcal 4 года назад

What is a fair price I should expect for this type of work from a mechanic? How much for parts and how much for labor? Thanks!

@SquadBustersAustralia 4 года назад

I currently have 3 days to pull this off I'm gonna have to do each side and each CV shaft cost $118 if you shop around, labour your looking around just under 300 depending on the mechanic but I might try do this with my dad

@ricksha_r5062 3 года назад

can someone tell me what the 6 bolts are that connect the axle to the diff? One of the 6 broke and I need to replace. Any ideas to where i can buy this bolt?

@johnargue2977 Месяц назад

3:31 axle nut hidden behind cap.

@perfectlyflawed3429 Год назад

Anybody know what size and with of the snap ring

@rdnetwork868 2 года назад

Ok so I have a 02 Nissan pathfinder rear wheel drive. I ordered this same part. But when i took the wheel off it looks nothing like how it looks in the video. There was no cv joint on it at all. Is the pathfinder in the video a 4x4?

@FierceSkatin 2 года назад

dude cv axles are only in the front why did you need to change yours if you dont any?

@dennislilly2818 Год назад

What about the bearing?

@cygnus1965 2 года назад

I just grab that cap With a pair a channel locks and a couple Wiggles and it pops right off.

@petermendoza7668 3 года назад

Is this the same process for a 95 pathfinder?

@TRQ 3 года назад

+Peter Mendoza The part in this video fits your application, and the install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-TRQ

@Mary-ef6jj 2 месяца назад

Anything looks easy when you have an edit button. Don't be fooled people you have to disconnect a lot more than je tells you, I was a fool and now the job is much bigger than it should have been if he would have been up front and honest to what all needs to be disconnected.

@zmyGe 3 года назад

This guy is in 1aauto channel too lol

@TRQ 3 года назад

+Mr. z'd out Thanks for watching our video! Yes, there are several mechanics that do videos for both channels! 1aau.to/m/Shop-TRQ

@jirizary73 3 месяца назад

DIY guys beware!! Its not just these guys, its other videos too. See the way those nuts came loose right away? That is BS. None of them say anything about the problems you can run into performing this repair. Im in the middle of it now. I had no other option and now its a way bigger problem. If you damage any of the bolts or nuts they are potentially hard to get. I'll learn my fate tomorrow. Vehicle or no Vehicle. Till then I'm dead in the water. I wish this was the only challenge I was under. Maybe i wouldn't feel so bad. Be careful out there.

@jirizary73 3 месяца назад

Im sitting here with my car apart. Neither those 12 mm upper bolts nor will the nuts on thos big bolt budge. Ive used lubricant then heat and nothing. plus i rounded one of those big nuts. My life is shit anyhow so im not actually expecting a response